Collaboration
ART
BEAUTÉ ET BIEN-ÊTRE
ARTISANAT
CULTURE ET HISTOIRE
DIVERTISSEMENT
ENVIRONNEMENT
NOURRITURE ET BOISSONS
INGÉNIERIE INVERSE
SCIENCES
SPORTS
TECHNOLOGIE
TECHNOLOGIE PORTABLE
Homemade Wood Lathe: Hardwood Bed, Sliding Headstock and Tailstock, Steel Spindle With Stepped Pulley (Boy Mechanic, 1915)
Woody

Créé par

Woody

13. novembre 2026NO
11
0
0
0
0

Homemade Wood Lathe: Hardwood Bed, Sliding Headstock and Tailstock, Steel Spindle With Stepped Pulley (Boy Mechanic, 1915)

E. E. Hulgan's lathe from The Boy Mechanic, Book 2 (1915), "in which wood and light metal articles may be turned": a 5 ft bed of two 2 by 4 in hardwood rails, a headstock clamped by bolts with a 3/4 in steel spindle in brass bearings and a three-step pulley, a bolted hardwood tailstock with a screw-fed dead centre, a sliding tool rest, and a screw-on chuck. Driven from a countershaft or by foot.
Avancé
About 1-2 weeks

Consignes

1

His sizes, and the pulley speeds

Chargement du notebook Jupyter…
2

Read The Boy Mechanic, Book 2

"A strong, substantial lathe in which wood and light metal articles may be turned can be made by carefully following the description below and the detailed drawings of the parts."
3

Make the bed

Cut two pieces of straight-grained, smooth 2 by 4 in hardwood, 5 ft long, and hold them apart at each end with blocks of wood 2 in wide (Fig. 9 shows 2 in rails with a 2 in gap). The bed can be longer or shorter.

Matériaux pour cette étape :

Planche de bois durPlanche de bois dur2 pièces
Vis à boisVis à bois1 pièce

Outils nécessaires :

Scie égoïneScie égoïne
RabotRabot
Chignole à mainChignole à main
Mètre rubanMètre ruban
4

Build the headstock frame

Make the two hardwood end pieces to the shape of Figs. 1 and 2 (2 in thick, 2 in apart on an 8 in base, 7-1/2 in high, 6 in wide at the bottom) and screw them to the base. Nail a slider 1 in thick and 10 in long, just wide enough to slide between the bed rails, under the base, 2 in from its rear end. Bore two 1/2 in holes through base and slider and put two 1/2 in bolts through them and through another slide and board under the bed, so tightening the nuts clamps the headstock. Screw a half-round wedge-shaped brace inside the frame against the front end.

Matériaux pour cette étape :

Planche de bois durPlanche de bois dur1 pièce
Boulon de carrosserieBoulon de carrosserie2 pièces
Écrou hexagonalÉcrou hexagonal2 pièces
Vis à boisVis à bois1 pièce
ClousClous1 pièce

Outils nécessaires :

Scie égoïneScie égoïne
Ciseaux à boisCiseaux à bois
Vilebrequin et mècheVilebrequin et mèche
Chignole à mainChignole à main
5

Make the spindle and bearings

Make the spindle of tool steel or steel tubing, 3/4 in in diameter and 14 in long, and cut a thread on one end. Rivet on a hardened steel collar, 1/4 by 1-1/2 in, to turn against another collar of the same size on the headstock; screw a third collar to the rear end piece and fix a collar with a removable pin on the spindle, fitted to turn easily with no end play. Drill brass tubing for the spindle as bearings and wedge them into the headstock 6 in above the bed, in line; drill small oil holes from the top.

Matériaux pour cette étape :

Barre d'acier à outilsBarre d'acier à outils1 pièce
Tube d'acierTube d'acier1 pièce
Shaft CollarShaft Collar4 pièces
Rivets en acierRivets en acier1 pièce
Tube en laitonTube en laiton1 pièce

Outils nécessaires :

Scie à métauxScie à métaux
Jeu de tarauds et filièresJeu de tarauds et filières
Chignole à mainChignole à main
Limes (lime à main)Limes (lime à main)
Étau d'établiÉtau d'établi
MarteauMarteau
6

Fit the stepped pulley

Make the pulleys 2 in wide, with the diameters on the drawing: 6, 4-1/2 and 3 in. Fasten them to the spindle with a removable pin. (Turned hardwood is our choice of material; he does not say.)

Matériaux pour cette étape :

Planche de bois durPlanche de bois dur1 pièce

Outils nécessaires :

Scie égoïneScie égoïne
Vilebrequin et mècheVilebrequin et mèche
Chignole à mainChignole à main
7

Make the chuck and centres

For the chuck (Fig. 3), take shafting 1-1/2 in in diameter and 2-1/2 in long, drill a 1/2 in hole through its centre, ream and thread one end to fit the spindle, and fit a setscrew over the 1/2 in hole. Make a wood-turning centre, and other centres and drills, from 1/2 in tool steel.

Matériaux pour cette étape :

Barre ronde en acier douxBarre ronde en acier doux1 pièce
Barre d'acier à outilsBarre d'acier à outils1 pièce
Vis sans tête à bout cuvetteVis sans tête à bout cuvette1 pièce

Outils nécessaires :

Scie à métauxScie à métaux
Chignole à mainChignole à main
AlésoirAlésoir
Jeu de tarauds et filièresJeu de tarauds et filières
Limes (lime à main)Limes (lime à main)
Étau d'établiÉtau d'établi
8

Build the tailstock

Build the tailstock (Figs. 4-6) of three pieces of hardwood 2 in thick and one 1 in thick, shaped as drawn, held together with four bolts 7-1/2 in long. Give it sliders and clamp it to the bed like the headstock, but with one bolt, and weld a handle to its nut for easy clamping. Drill a piece of tubing 2 in long for a 1/2 in dead centre and set it 1-1/2 in into the joint between the two upper pieces. Bore for a 1/2 in bolt to slide in the tube; chisel a recess behind the tube for a 1/2 in nut; turn a bolt 7 in long, threaded for 2 in, into nut and tube, and rivet a handle or wheel on its end. Make the centre of 1/2 in tool steel with a tapered point.

Matériaux pour cette étape :

Planche de bois durPlanche de bois dur2 pièces
Boulon de carrosserieBoulon de carrosserie5 pièces
Écrou hexagonalÉcrou hexagonal2 pièces
Tube d'acierTube d'acier1 pièce
Barre d'acier à outilsBarre d'acier à outils1 pièce
Rivets en acierRivets en acier1 pièce

Outils nécessaires :

Scie égoïneScie égoïne
Ciseaux à boisCiseaux à bois
Vilebrequin et mècheVilebrequin et mèche
Chignole à mainChignole à main
Forge à charbonForge à charbon
EnclumeEnclume
Marteau de forgeronMarteau de forgeron
Limes (lime à main)Limes (lime à main)
9

Make the tool rest

The tool rest (Figs. 7-9) has a slide 3/4 by 3 by 13 in with a slot 1/2 by 6 in. Bolt the rest base on the slide so it can be adjusted, and screw the rest to the base. Raise or lower it with wedges between slide and base, and clamp it to the bed like the tailstock.

Matériaux pour cette étape :

Planche de bois durPlanche de bois dur1 pièce
Boulon de carrosserieBoulon de carrosserie1 pièce
Écrou hexagonalÉcrou hexagonal1 pièce
Vis à boisVis à bois1 pièce

Outils nécessaires :

Scie égoïneScie égoïne
Ciseaux à boisCiseaux à bois
Vilebrequin et mècheVilebrequin et mèche
10

Troubleshooting

Wood lathe troubleshooting.

Flow

Loading...
11

History and honest limits

From "How to Make a Wood Lathe" by E. E. Hulgan, Marion, Ind., in **The Boy Mechanic, Book 2**, Popular Mechanics, 1915 (Project Gutenberg 44585; checked on the archive.org scan boymechanicbook200chic2, pp. 434-436). Part shapes come from his Figs. 1-9; he gives no pulley material and no countershaft or foot-drive details. The pulley material, tools and metric figures are ours.

Matériaux

12

Outils requis

15

CC0 Domaine public

Ce blueprint est publié sous CC0. Vous êtes libre de copier, modifier, distribuer et utiliser ce travail pour tout usage, sans demander la permission.

Soutenez le Maker en achetant des produits via son Blueprint où il perçoit une Commission Maker définie par les Vendeurs, ou créez une nouvelle itération de ce Blueprint et incluez-le comme connexion dans votre propre Blueprint pour partager les revenus.

Commentaires

(0)

Se connecter pour participer à la discussion

Chargement des commentaires...