ART
BEAUTÉ ET BIEN-ÊTRE
ARTISANAT
CULTURE ET HISTOIRE
DIVERTISSEMENT
ENVIRONNEMENT
NOURRITURE ET BOISSONS
INGÉNIERIE INVERSE
SCIENCES
SPORTS
TECHNOLOGIE
TECHNOLOGIE PORTABLE
Cast Acrylic Sheet
Pixel

Créé par

Pixel

22. septembre 2026FI
2
0
0
0
0

Cast Acrylic Sheet

Otto Röhm had worked on acrylic chemistry since his 1901 doctorate. His firm first used polymethacrylate as the sticky middle layer of laminated safety glass - and noticed that the polymer came away from the glass plates cleanly, leaving a clear sheet as smooth as the glass. Sold from 1933 as Plexiglas, the sheet went into aircraft canopies within the decade. **US 2,154,639**, "Process for the manufacture of polymerization products", Röhm and Bauer, assigned to Röhm & Haas, filed 4. December 1935, granted 18. April 1939: methacrylic esters polymerised between sheets of glass and then separated from them, for "glass substitutes" whose faces are "as highly polished as the surfaces of the glass itself". **You use that polish**: an edge-lit sign whose engraving glows while the smooth faces stay dark, and two heat-bent offcuts that show how tight a bend the light survives.
Débutant
3 hours

Consignes

1

Cut the panel

Keep the protective film on. Score 3 mm cast acrylic 200 x 120 mm with the utility knife against a ruler, 8 to 10 passes, then snap it over the bench edge. Cut two 100 x 30 mm offcuts the same way.

Matériaux pour cette étape :

Plaque acryliquePlaque acrylique1 pièce

Outils nécessaires :

CutterCutter
Règle en acierRègle en acier
Lunettes de sécurité transparentesLunettes de sécurité transparentes
2

Polish the light edge

Sand the 120 mm bottom edge flat, then run the Micro-Mesh grits in order until it is clear. Light enters here; a frosted edge scatters it at the door.

Outils nécessaires :

Kit de ponçage micro-maille (9 grains)Kit de ponçage micro-maille (9 grains)
3

Engrave the back

Peel the back film. Draw your design on paper, tape it under the sheet, and trace it with the engraving point at medium speed, light pressure.

Outils nécessaires :

Outil rotatif (type Dremel)Outil rotatif (type Dremel)
Pointe à graverPointe à graver
Lunettes de sécurité transparentesLunettes de sécurité transparentes
4

Slot the base

Cut a pine block 160 x 60 x 40 mm. Saw two parallel kerfs 3.5 mm apart, 15 mm deep, along its length and chisel out between them. Chisel a channel underneath for the LED strip to shine up into the slot.

Matériaux pour cette étape :

Planche de pinPlanche de pin1 pièce

Outils nécessaires :

Scie égoïneScie égoïne
Jeu de ciseaux à boisJeu de ciseaux à bois
5

Light it

Strip 5V, GND and DIN to the Uno's 5V, GND and D6. Install the Adafruit NeoPixel library and upload. Stand the panel in the slot.
edge_lit_panel.inocpp
// Edge-lit acrylic panel - batch 98, US 2,154,639
// A short WS2812B strip under the panel's bottom edge. Data -> D6 through the strip's own input.
#include <Adafruit_NeoPixel.h>

const int PIN = 6;
const int COUNT = 8;          // LEDs under the 120 mm edge
Adafruit_NeoPixel strip(COUNT, PIN, NEO_GRB + NEO_KHZ800);

void setup() {
  strip.begin();
  strip.setBrightness(60);    // keep well under full power when run from USB
}

void loop() {
  // slow colour wheel: the engraving glows, the polished faces stay dark
  for (long hue = 0; hue < 65536; hue += 256) {
    strip.fill(strip.gamma32(strip.ColorHSV(hue)));
    strip.show();
    delay(30);
  }
}

Matériaux pour cette étape :

Ruban de LED NeopixelRuban de LED Neopixel1 pièce
Jeu de câbles Dupont (mâle-femelle)Jeu de câbles Dupont (mâle-femelle)1 jeu

Outils nécessaires :

Arduino Uno R3Arduino Uno R3
SparkFun Cerberus USB Cable - 1.8 meterSparkFun Cerberus USB Cable - 1.8 meter
6

Bend two offcuts

Heat an offcut along a line on the strip heater, turning it over every 30 seconds, until it flexes. Bend it 90° round a 6 mm dowel and hold until cool. Bend the second round a 20 mm dowel.

Matériaux pour cette étape :

Goujon en boisGoujon en bois1 pièce

Outils nécessaires :

Chauffe-bande pour acryliqueChauffe-bande pour acrylique
Gants de soudeurGants de soudeur
7

Trace the beam

In a dim room shine the laser pointer into the end of each bent strip, never towards anyone's eyes. See where light escapes at the bend, and compare with the notebook.

Outils nécessaires :

Pointeur laserPointeur laser
8

Critical angle and bends

Chargement du notebook Jupyter…
9

History & Context

**What the patent specifies:** methacrylic esters polymerised between glass sheets and separated, giving a glass substitute with glass-polished faces. **Modern build (derived):** commercial cast acrylic sheet, cut and heat-bent. Cast sheet is still made between glass plates; cheaper extruded sheet came later and is softer and more prone to crazing. The limits: acrylic scratches, cracks if drilled carelessly, crazes when solvents or stress meet, and burns.
Étape 9 - Image 1

Matériaux

5

Outils requis

13

Blueprints liés

Ces blueprints partagent des connaissances — techniques, matériaux ou principes

Polycarbonate

Polycarbonate

par PennyDK

Mécanique

0
0
0
0
0
0
Laminated Safety Glass

Laminated Safety Glass

par MaryFI

Chimie

37
0
0
0
0
0

CC0 Domaine public

Ce blueprint est publié sous CC0. Vous êtes libre de copier, modifier, distribuer et utiliser ce travail pour tout usage, sans demander la permission.

Soutenez le Maker en achetant des produits via son Blueprint où il perçoit une Commission Maker définie par les Vendeurs, ou créez une nouvelle itération de ce Blueprint et incluez-le comme connexion dans votre propre Blueprint pour partager les revenus.

Commentaires

(0)

Se connecter pour participer à la discussion

Chargement des commentaires...