Collaboration
ART
BEAUTÉ ET BIEN-ÊTRE
ARTISANAT
CULTURE ET HISTOIRE
DIVERTISSEMENT
ENVIRONNEMENT
NOURRITURE ET BOISSONS
INGÉNIERIE INVERSE
SCIENCES
SPORTS
TECHNOLOGIE
TECHNOLOGIE PORTABLE

DC Power Supply: SCR-Regulated, Voltage and Current Bridges with Automatic Cross-Over (Kupferberg & Ash, Forbro, US 3,305,763, 1967)
A variable DC supply regulated by controlled rectifiers instead of a series transistor. Two of the four rectifiers in the bridge are silicon controlled rectifiers; how late in each half-cycle they are fired sets the output. A voltage bridge and a current bridge each make an error signal, an analog OR gate passes whichever is larger, and the supply crosses over automatically between holding the voltage and holding the current.
Result: a variable voltage / current regulated DC supply with automatic cross-over.
Source: K. Kupferberg and J. Ash (Forbro Design), US 3,305,763 (1967), Fig. 1. Unknown: component values and the firing-angle circuit. Picture: the patent drawing.
Avancé
Unknown
Consignes
1
1
Build the controlled rectifier bridge
Build the controlled rectifier bridge
In a case, wire the cord through a switch and fuse to a transformer. Feed its secondary into a bridge of two ordinary rectifiers and two silicon controlled rectifiers. Smooth the negative output through a choke and a capacitor, then through a current-sensing resistor (with a second capacitor forming a further filter) to the negative output terminal; the positive goes straight to the positive terminal. Ours: the case, switch and fuse. Not given: the ratings.
Matériaux pour cette étape :
Boîtier en aluminium1 pièce
Cordon souple avec fiche1 pièce
Interrupteur à levier1 pièce
Fusible1 pièce
Transformateur abaisseur1 pièce
Diode2 pièces
Thyristor (SCR)2 pièces
Self de filtrage1 pièce
Condensateur électrolytique2 pièces
Borne de sortie2 output + and -Outils nécessaires :
Chignole à main
Jeu de tournevis2
2
Build the two bridges
Build the two bridges
Current bridge: the sensing resistor, a reference Zener, a fixed resistor and the variable current-control resistor. Voltage bridge: the load across the output, the variable voltage-control resistor, a fixed resistor and a second reference Zener. Feed both Zeners from a small separate supply. Not given: the values, the Zener supply.
Matériaux pour cette étape :
Diode Zener2 pièces
Rhéostat2 voltage and current controls
Résistance1 sensing and bridge resistorsOutils nécessaires :
Fer à souder3
3
Build the control chain and use it
Build the control chain and use it
Invert the current bridge's error in a phase-reversing amplifier and feed it, with the voltage bridge's error, to an analog OR gate that passes the larger. Amplify the result and feed it to a firing-angle control circuit that fires the two controlled rectifiers' gates later or earlier in each half-cycle. In use, set the voltage and the current: for any load larger than the cross-over resistance (voltage setting divided by current setting) the supply holds the voltage, for a smaller one the current. Not given: the amplifier, OR-gate and firing circuits in this form.
Matériaux pour cette étape :
Circuit imprimé1 pièce
Assortiment de transistors1 amplifiers
Matériau inconnu1 OR gate and firing-angle circuit
Fil de soudure1 as neededOutils nécessaires :
Fer à souderMatériaux
17- 1 pièceEspace réservé
- 1 pièceEspace réservé
- Espace réservé
- 1 pièceEspace réservé
- 1 pièceEspace réservé
- 2 piècesEspace réservé
- 2 piècesEspace réservé
- 1 pièceEspace réservé
- 2 piècesEspace réservé
- Espace réservé
- 2 piècesEspace réservé
- 2 voltage and current controlsEspace réservé
- 1 sensing and bridge resistorsEspace réservé
- 1 pièceEspace réservé
- 1 amplifiersEspace réservé
- 1 OR gate and firing-angle circuitEspace réservé
- 1 as neededEspace réservé
Outils requis
3- Espace réservé
- Espace réservé
- 2 vendors sell this, none ship to you yetEspace réservé
Ce plan fabrique
Blueprints liés
Ces blueprints partagent des connaissances — techniques, matériaux ou principes
CC0 Domaine public
Ce blueprint est publié sous CC0. Vous êtes libre de copier, modifier, distribuer et utiliser ce travail pour tout usage, sans demander la permission.
Soutenez le Maker en achetant des produits via son Blueprint où il perçoit une Commission Maker définie par les Vendeurs, ou créez une nouvelle itération de ce Blueprint et incluez-le comme connexion dans votre propre Blueprint pour partager les revenus.

