Collaboration
ART
BEAUTÉ ET BIEN-ÊTRE
ARTISANAT
CULTURE ET HISTOIRE
DIVERTISSEMENT
ENVIRONNEMENT
NOURRITURE ET BOISSONS
INGÉNIERIE INVERSE
SCIENCES
SPORTS
TECHNOLOGIE
TECHNOLOGIE PORTABLE
New Year Noisemaker: a Spun Box Whose Wooden Tongues Clack Over a Pinned Bobbin (Folkush, 1921)
Woody

Créé par

Woody

13. novembre 2026NO
8
0
0
0
0

New Year Noisemaker: a Spun Box Whose Wooden Tongues Clack Over a Pinned Bobbin (Folkush, 1921)

Martin Folkush of Milwaukee received US 1,374,644, dated 12 April 1921, for a noisemaker "that can be heard for a great distance". Hold the handle and swing the box round it: two thin wooden tongues inside snap over the posts of a fixed bobbin, one in single clacks and one in double, and the box rings like a sounding board. A slider changes the pitch. We make it from plywood, dowel and hardwood strip. All sizes are ours.
Intermédiaire
About 4 hours

Consignes

1

Posts on the bobbin

Chargement du notebook Jupyter…
2

Read US 1,374,644

"Upon rotating the casing 12 upon the shaft 11, the sounding boards 21 and 22 will be brought into violent engagement with the posts 19 and 20 causing loud sounds to be emitted."
3

Make the handle and shaft

Shape a handle from hardwood handle stock with a rasp, his handle 10, and glue a dowel shaft 11 into its end.

Matériaux pour cette étape :

Barreau de bois dur pour manchesBarreau de bois dur pour manches1 pièce
Goujons de bois durGoujons de bois dur1 pièce
Colle à boisColle à bois1 pièce

Outils nécessaires :

Scie égoïneScie égoïne
Râpe à boisRâpe à bois
Papier abrasifPapier abrasif
Chignole à mainChignole à main
4

Make the bobbin

Cut three plywood disks 60 mm across (ours): two ends and the middle disk 18. Drill all three on the circle from the notebook and glue dowel posts 19 through all of them; then glue the shorter posts 20 between the middle disk and one end disk only, between the long ones. Drill the centre for the shaft and pin the bobbin to it, his pin 17.

Matériaux pour cette étape :

Panneau de contreplaquéPanneau de contreplaqué1 pièce
Goujons de bois durGoujons de bois dur1 pièce
Colle à boisColle à bois1 pièce
ClousClous1 pièce

Outils nécessaires :

Scie à chantournerScie à chantourner
Compas à pointes sèchesCompas à pointes sèches
Chignole à mainChignole à main
Scie égoïneScie égoïne
5

Make the casing

Cut two plywood sides 14 with a round head 13 at one end, bored for the shaft. Join them with a closed end 24 and an open frame so the bobbin turns freely between the heads. Glue a cross rib 23 inside the closed end. Cut a slot 28 in each side for the slider.

Matériaux pour cette étape :

Panneau de contreplaquéPanneau de contreplaqué1 pièce
Colle à boisColle à bois1 pièce
ClousClous1 pièce

Outils nécessaires :

Scie égoïneScie égoïne
Scie à chantournerScie à chantourner
Chignole à mainChignole à main
6

Fit the sounding boards

Cut two thin hardwood strips (his sounding boards 21 and 22) long enough to reach from the rib to just inside the circle of posts, and screw their ends to the rib, side by side, one opposite each half of the bobbin.

Matériaux pour cette étape :

Baguette de bois durBaguette de bois dur1 pièce
Vis à boisVis à bois1 pièce

Outils nécessaires :

Scie égoïneScie égoïne
Chignole à mainChignole à main
Jeu de tournevisJeu de tournevis
7

Fit the slider and close the box

Make a small wooden slider 26 that surrounds both boards, with a length of threaded rod through it whose ends pass out through the slots; put a wing nut on each end (his set nuts 29). Put the casing on the shaft over the bobbin and close the other side with a plywood plate 25, making a resonant box.

Matériaux pour cette étape :

Baguette de bois durBaguette de bois dur1 pièce
Tige filetéeTige filetée1 pièce
Écrou papillonÉcrou papillon2 pièces
Panneau de contreplaquéPanneau de contreplaqué1 pièce
Colle à boisColle à bois1 pièce

Outils nécessaires :

Scie égoïneScie égoïne
Chignole à mainChignole à main
Scie à métauxScie à métaux
8

Play it

Hold the handle and swing the box round the shaft: the boards snap over the posts. Slide the slider toward the bobbin for a higher, sharper sound, away for a deeper one, and lock it with the wing nuts.
9

Troubleshooting

Noisemaker troubleshooting.

Flow

Loading...
10

History and honest limits

**Martin Folkush** of Milwaukee, US 1,374,644, dated 12 April 1921, filed 10 April 1920. He claimed "a noise maker comprising a shaft, a casing journaled thereon, a frame having spaced end supported posts", "one half of said frame being provided with double the number of posts that the other half has", and the pitch-adjusting slider. He names no materials and gives no sizes: the wood, all sizes, wing nuts and threaded rod are ours.

Matériaux

9

Outils requis

8

CC0 Domaine public

Ce blueprint est publié sous CC0. Vous êtes libre de copier, modifier, distribuer et utiliser ce travail pour tout usage, sans demander la permission.

Soutenez le Maker en achetant des produits via son Blueprint où il perçoit une Commission Maker définie par les Vendeurs, ou créez une nouvelle itération de ce Blueprint et incluez-le comme connexion dans votre propre Blueprint pour partager les revenus.

Commentaires

(0)

Se connecter pour participer à la discussion

Chargement des commentaires...