ART
BEAUTÉ ET BIEN-ÊTRE
ARTISANAT
CULTURE ET HISTOIRE
DIVERTISSEMENT
ENVIRONNEMENT
NOURRITURE ET BOISSONS
INGÉNIERIE INVERSE
SCIENCES
SPORTS
TECHNOLOGIE
TECHNOLOGIE PORTABLE
Getting the Solid Back: Evaporate, Crystallise, and Dry to Constant Mass
Charlie

Créé par

Charlie

24. septembre 2026DE
23
0
0
0
0

Getting the Solid Back: Evaporate, Crystallise, and Dry to Constant Mass

Boiling a solution dry gives you everything that was dissolved in it, including the impurities. Letting it crystallise slowly gives you the substance you wanted and leaves most of the impurities in the liquid — because a growing crystal is fussy about what it lets in. So evaporating to dryness and crystallising are not two ways of doing the same job. The first is for recovering everything; the second is for purifying. Then there is the question of when it is actually DRY, which cannot be answered by looking. The answer is a measurement loop: dry, weigh, dry again, weigh again, and stop when the mass stops changing.
Intermédiaire
3 hours

Consignes

1

Evaporate gently, and never to the last drop over heat

Use a wide, shallow evaporating dish rather than a beaker: evaporation happens at the surface, so the area is what sets the speed, and a wide dish is faster at a much lower temperature. Stop while a little liquid remains and let the rest go at room temperature. Once the liquid is nearly gone there is nothing left to absorb the heat, the solid overheats in seconds, and it spits, decomposes or bakes onto the dish. A steam bath or a hot plate on a low setting is better than a flame for anything that matters. Direct flame heats one spot far above the boiling point of the solution, and many substances that survive 100 degrees do not survive that.

Matériaux pour cette étape :

Eau distilléeEau distillée1 litre
Chlorure de sodium (sel)Chlorure de sodium (sel)1 pièce

Outils nécessaires :

Capsule d'évaporationCapsule d'évaporation
Plaque chauffantePlaque chauffante
Verre de montreVerre de montre
2

Crystallise slowly, and crystallise on purpose

Dissolve the solid in the smallest volume of hot solvent that will take it, then let it cool UNDISTURBED. Slow cooling grows few, large, pure crystals; rapid cooling or stirring gives a mass of tiny ones that trap the mother liquor and everything dissolved in it. If nothing appears, it is usually because there is too much solvent or because there is no nucleus to start on. Boil a little solvent off, scratch the inside of the glass with a rod at the surface, or add one seed crystal. Then filter the crystals off cold and rinse them with a SMALL amount of ICE-COLD solvent. Rinsing with warm solvent dissolves the product you just spent an hour growing, which is the most disheartening way to lose a yield.

Matériaux pour cette étape :

Eau distilléeEau distillée1 litre
Sulfate de cuivre pentahydraté (CuSO4·5H2O)Sulfate de cuivre pentahydraté (CuSO4·5H2O)1 pièce

Outils nécessaires :

Bécher en verreBécher en verre
Baguette de verreBaguette de verre
Entonnoir de Büchner (en porcelaine)Entonnoir de Büchner (en porcelaine)
Papier filtrePapier filtre
3

Dry to constant mass, which is a measurement not a judgement

Chargement du notebook Jupyter…

Matériaux pour cette étape :

Chlorure de sodium (sel)Chlorure de sodium (sel)1 pièce

Outils nécessaires :

Étuve de séchageÉtuve de séchage
Dessiccateur en verreDessiccateur en verre
Balance de précisionBalance de précision
Ordinateur de bureauOrdinateur de bureau
4

Work out the yield, and be honest about it

Percentage yield is what you got divided by what the equation says you could have got. Both numbers have to be real: the mass actually recovered and dried, and the theoretical mass calculated from the LIMITING reagent. Yields above 100% mean the product is not dry, or it has picked up something. That is worth treating as a fault rather than a bonus, because a wet product weighs more and is worth less. Record where the losses went, in the notebook: left in the mother liquor, stuck to the filter paper, lost in the rinse, spilled. Those lines are what make the next attempt better, and a yield with no explanation attached is a number nobody can improve.

Outils nécessaires :

Balance de précisionBalance de précision
CalculatriceCalculatrice

Matériaux

3

Outils requis

12

CC0 Domaine public

Ce blueprint est publié sous CC0. Vous êtes libre de copier, modifier, distribuer et utiliser ce travail pour tout usage, sans demander la permission.

Soutenez le Maker en achetant des produits via son Blueprint où il perçoit une Commission Maker définie par les Vendeurs, ou créez une nouvelle itération de ce Blueprint et incluez-le comme connexion dans votre propre Blueprint pour partager les revenus.

Commentaires

(0)

Se connecter pour participer à la discussion

Chargement des commentaires...