Collaboration
ART
BEAUTÉ ET BIEN-ÊTRE
ARTISANAT
CULTURE ET HISTOIRE
DIVERTISSEMENT
ENVIRONNEMENT
NOURRITURE ET BOISSONS
INGÉNIERIE INVERSE
SCIENCES
SPORTS
TECHNOLOGIE
TECHNOLOGIE PORTABLE

Rotary Lawn Sprinkler: a Barker's-Mill Head Turning on Balls Round the Supply Pipe (Gibbs, 1901)
Henry Gibbs of Chicago received US 683,645, dated 1 October 1901, for a lawn sprinkler "operating on the familiar Barker's mill principle": water leaving its arms sideways pushes the head round. His head turns on a ring of steel balls held in matching grooves in the head and in the end of the supply pipe, so it spins freely with little friction and stays on.
We turn the head from brass and the groove in a steel pipe on the lathe. All sizes are ours.
Intermédiaire
About 5 hours
Consignes
1
1
How many balls
How many balls
Chargement du notebook Jupyter…
2
2
Read US 683,645
Read US 683,645
"It being only necessary that certain of the orifices shall discharge the water tangentially to revolve the head 14 and spray-pipes 15 in the well-known manner."
3
3
Groove the supply pipe
Groove the supply pipe
Chuck a length of steel pipe (his pipe 13) and finish its top end smooth and round. Cut a half-round groove (his 17) round it a little below the end, to the depth the notebook gives, with a round-nosed tool. Use thick-walled pipe, so at least 1.5 mm of wall is left under the groove (ours).
Matériaux pour cette étape :
Tube d'acier (à paroi épaisse, bouts filetés)1 pièceOutils nécessaires :
Tour à métaux
Mandrin de tour à 3 mors
Outil de coupe pour tour
Pied à coulisse numérique 6 pouces4
4
Turn the head
Turn the head
Turn a brass bar to a short round head (his 14). Bore it from below to loosely fit the pipe end, his bore 16, but stop short of the top so a lip (his flange 22) overhangs the pipe end. Cut a matching groove 18 inside the bore at the same height as the pipe's groove.
Matériaux pour cette étape :
Barre ronde de laiton1 pièceOutils nécessaires :
Tour à métaux
Mandrin de tour à 3 mors
Outil de coupe pour tour
Jeu de forets à centrer
Jeu de forets
Pied à coulisse numérique 6 pouces5
5
Drill the ball hole and the arms
Drill the ball hole and the arms
Drill a hole (his opening 20) through the head's side into the groove, just bigger than a ball, and tap it for a screw plug (21). Drill three holes round the head into the bore for the spray pipes.
Outils nécessaires :
Perceuse à colonne
Jeu de forets
Jeu de tarauds et filières
Étau d'établi6
6
Make the spray pipes
Make the spray pipes
Cut three lengths of copper tube, close their outer ends, and bend the last bit of each upward as his Fig. 1. Drill small holes near the ends, some pointing sideways (tangentially), all the same way round, so the jets turn the head. Solder the pipes into the head's holes (ours; he threads them in).
Matériaux pour cette étape :
Tube de cuivre1 pièce
Soudure étain-plomb1 pièce
Flux1 pièceOutils nécessaires :
Scie à métaux
Jeu de forets
Perceuse à colonne
Fer à souder électrique
Étau d'établi7
7
Assemble with the balls
Assemble with the balls
Slide the head onto the pipe end with the grooves level. Feed balls in through the side hole, turning the head, until the race is full; then screw in the plug. The head should spin freely and not lift off.
Matériaux pour cette étape :
Roulements à billes en acier1 pièce
Vis à métaux1 pièceOutils nécessaires :
Clé à molette8
8
Make the stand
Make the stand
Bore a hardwood block to hold the pipe upright and glue in three splayed dowel legs (ours; his base 10 and supports 11). Screw the hose coupling onto the pipe's lower end below the block (his coupling 12).
Matériaux pour cette étape :
Bloc de bois dur1 pièce
Goujons de bois dur1 pièce
Colle à bois1 pièce
Raccord de tuyau1 pièceOutils nécessaires :
Scie égoïne
Perceuse à colonne
Jeu de forets9
9
Run it
Run it
Connect a garden hose and turn on the water slowly: the jets push the head round and throw the water in a circle. More pressure turns it faster.
10
10
Troubleshooting
Troubleshooting
Lawn sprinkler troubleshooting.
Flow
Loading...
11
11
History and honest limits
History and honest limits
**Henry Gibbs** of Chicago, assignor to W. D. Allen Manufacturing Company, US 683,645, dated 1 October 1901, filed 20 May 1901. He claimed a single-piece hollow coupling with radial spray pipes having tangential orifices, a bore loosely fitting the supply pipe, "annular grooves in the opposed cylindrical faces of said bore and said pipe" and "bearing balls interposed in said grooves". He gives no sizes or metals; the brass, steel pipe, ball size, soldered copper arms and the wooden stand are ours.
Matériaux
11- Espace réservé
- 1 pièceEspace réservé
- 1 pièceEspace réservé
- 1 pièceEspace réservé
- 1 pièceEspace réservé
- 1 pièceEspace réservé
- 1 pièceEspace réservé
- 1 pièceEspace réservé
- 1 pièceEspace réservé
- 1 pièceEspace réservé
- 1 pièceEspace réservé
Outils requis
13- Espace réservé
- Espace réservé
- Espace réservé
- Espace réservé
- Espace réservé
- Espace réservé
- Espace réservé
- Espace réservé
- Espace réservé
- Espace réservé
- Espace réservé
- Espace réservé
- Espace réservé
Ce plan fabrique
Blueprints liés
Ces blueprints partagent des connaissances — techniques, matériaux ou principes
CC0 Domaine public
Ce blueprint est publié sous CC0. Vous êtes libre de copier, modifier, distribuer et utiliser ce travail pour tout usage, sans demander la permission.
Soutenez le Maker en achetant des produits via son Blueprint où il perçoit une Commission Maker définie par les Vendeurs, ou créez une nouvelle itération de ce Blueprint et incluez-le comme connexion dans votre propre Blueprint pour partager les revenus.


