Collaboration
ART
BEAUTÉ ET BIEN-ÊTRE
ARTISANAT
CULTURE ET HISTOIRE
DIVERTISSEMENT
ENVIRONNEMENT
NOURRITURE ET BOISSONS
INGÉNIERIE INVERSE
SCIENCES
SPORTS
TECHNOLOGIE
TECHNOLOGIE PORTABLE
Hand-Sewn Welted Boot: Last, Welt, Sole, Heel and Finish (Hasluck, Boot Making and Mending, 1898)
Tex

Créé par

Tex

13. novembre 2026FO
12
0
0
0
0

Hand-Sewn Welted Boot: Last, Welt, Sole, Heel and Finish (Hasluck, Boot Making and Mending, 1898)

How a closed boot upper becomes a hand-sewn welted boot, from Paul N. Hasluck's Boot Making and Mending (1898): measure the foot and fit up the last, block and feather the insole, last the upper tight, sew in the welt and the seat, fill and lay the sole, round it, channel and stitch it to the welt, build and sew the heel, then knife, iron, ink and heel-ball the edges. All sizes are his. The upper here is the Wellington leg from Leno's book (the previous blueprint).
Avancé
About 1 week

Consignes

1

Sizes, lasts and heel

Chargement du notebook Jupyter…
2

Read Boot Making and Mending, ch. IV

"In choosing the materials, it should be remembered that a boot, like a house, depends upon the foundation, for which reason the leather should be good of its class, and every care exercised to fit it properly."
3

Measure the foot

Have the person stand full weight on a sheet of paper and draw round the foot with the pencil quite upright, then the lines of the waist. Take the length on the drawing. With a tape take, in inches and only just tight: the joint (under the foot, over the great-toe joint and little-toe knuckle), the second joint round the ball, the instep, the heel measure (round the heel, under the ankle bone, across the throat) and the leg about 1½ in above the ankle bone. Mark each on the drawing.

Matériaux pour cette étape :

Feuille de papier carréeFeuille de papier carrée1 pièce

Outils nécessaires :

CrayonCrayon
Mètre rubanMètre ruban
PointureurPointureur
4

Fit up the last

Choose a last whose toe is nearest the shape wanted; set it on the drawing and check the lines and girths. Rasp off any surplus so the bottom is shaped as his Fig. 69, leaving room for the great toe. If it is too small, make fittings from wetted, stretched flank leather (long leather, joint, toe-pin, heel-pin), skive them thin to the edge, tack them on wet and let each dry before blocking and trimming. Peg bunion pieces with fine ½ in pegs in holes made with the peg awl. An old shoe worn to the foot is "the safest guide": put the last in it to see where it is short.

Matériaux pour cette étape :

Cuir de harnaisCuir de harnais1 pièce
Chevilles en boisChevilles en bois1 pièce
Semences de montageSemences de montage1 pièce

Outils nécessaires :

Forme de cordonnierForme de cordonnier
RâpeRâpe
Couteau à parer le cuirCouteau à parer le cuir
Alène à chevillesAlène à chevilles
Marteau à panne fendueMarteau à panne fendue
5

Prepare the stuff

Soak insoles, outer soles, stiffeners, lifts and top-pieces in clean water. Mark the welts down the centre with compasses, cut them to equal widths and put them in the water too; they are used wet. Dry the rest in a draught, not near a fire. When the soles are just mellow, buff off the grain lightly and skive the flesh off the back; do the same to lifts and top-pieces. Hammer them evenly all over on the lap iron, grain down, from the centre; the lifts less hard than soles and top-pieces.

Matériaux pour cette étape :

Cuir à semellesCuir à semelles1 pièce
Trépointe de cuirTrépointe de cuir1 pièce
EauEau1 pièce

Outils nécessaires :

Compas à pointes sèchesCompas à pointes sèches
Couteau à cuirCouteau à cuir
Racloir de cordonnierRacloir de cordonnier
Fer à genouxFer à genoux
Marteau à panne fendueMarteau à panne fendue
6

Block, feather and hole the insole

Mark the insole to the last, cut it out, buff the grain and tack it grain down with four tacks in the middle; stretch the sides with pincers and tack it tight till nearly dry (blocking). Round it to the last, narrower in the waist. Rub with soap, draw a margin ¼ to ⅓ in from the edge with compasses, wider at the waist, cut it about one-third through with the knife upright, open it with the prick-stitch and cut away the strip to leave the feather. Gauge a second line the same distance in and pass the sewing awl from it to the edge of the feather. Take the sharp edge off the grain side.

Matériaux pour cette étape :

Cuir à semellesCuir à semelles1 pièce
Semences de montageSemences de montage1 pièce
Pain de savonPain de savon1 pièce

Outils nécessaires :

Forme de cordonnierForme de cordonnier
Couteau à cuirCouteau à cuir
Pince à monterPince à monter
Compas à pointes sèchesCompas à pointes sèches
Pique-pointsPique-points
Alène à coudreAlène à coudre
7

Stiffeners and side linings

Cut the stiffeners from good leather, used wet; a gentleman's 1¾ in high at the back. Skive them all round on both sides, little on the grain side, the top to a feather edge, the bottom to half its substance. Cut side linings, best of oil-dressed calf.

Matériaux pour cette étape :

Cuir à semellesCuir à semelles1 pièce
Cuir de veauCuir de veau1 pièce

Outils nécessaires :

Couteau à parer le cuirCouteau à parer le cuir
8

Last the upper

Paste the stiffener on both sides and put it between lining and leather at the back seam. With the last on your knees, pull the upper down at the toe and set the back seam on the centre of the last, covering about two-thirds of it at the back ("horsing"). Draw the toe tight with the pincers and tack at A, then B and B, then the draft tacks C and C, pulling hard to put a draft in. Put the side linings in unpasted and tack D and D, lasting the lining tight. Last the sides till all fulness is gone, knock the heel of the last in, and last waist and seat, less hard. Last the toe last, drawing stuff to the toe and tapping out every pipe and wrinkle with the hammer; never cut V-pieces out of the pipes.

Matériaux pour cette étape :

Tige de botteTige de botte1 pièce
Colle de pâte de bléColle de pâte de blé1 pièce
Semences de montageSemences de montage1 pièce

Outils nécessaires :

Forme de cordonnierForme de cordonnier
Pince à monterPince à monter
Marteau à panne fendueMarteau à panne fendue
Alène à coudreAlène à coudre
9

Prepare the welts

Take a fine shaving off the grain side of the wet welts and, if needed, reduce them from the flesh side. Cut an angular piece about ³⁄₁₆ in wide, about two-thirds through, along one corner of the grain side, by pulling the welt past a knife dug into the cutting-board. Choose the width from the notebook.

Matériaux pour cette étape :

Trépointe de cuirTrépointe de cuir1 pièce

Outils nécessaires :

Couteau à cuirCouteau à cuir
Planche de pinPlanche de pin
10

Make the threads and sew in the welt

Make waxed threads of hemp with cobbler's wax and a bristle at each end, nicely twisted and smooth. Damp the boot over the holes. Starting at the left corner of the seat, toe toward you, held with a strap under your foot over the waist, skive the welt to half its substance for the waist length. Pass the sewing awl through the insole hole and the welt, put both bristles through from opposite sides, pull the stitch through in quick strokes and set it with a hard tightening pull, the thread round the hand leather and the awl handle. Hammer the seam every five or six stitches; wax the ends as you go. Draw each lasting tack as you reach it. Skive the welt again at the other joint, sew to F and cut it off under the last stitch. Trim the surplus upper close to the stitch and hammer the seam down.

Matériaux pour cette étape :

Trépointe de cuirTrépointe de cuir1 pièce
Fibre de chanvreFibre de chanvre1 pièce
Poix de cordonnierPoix de cordonnier1 pièce
Soies de sanglierSoies de sanglier1 pièce

Outils nécessaires :

Alène à coudreAlène à coudre
ManicleManicle
Lanière de cuirLanière de cuir
Marteau à panne fendueMarteau à panne fendue
Couteau à cuirCouteau à cuir
11

Sew the seat

Wax the ends well; use one thread long enough to go right round. Sew the heel seat the same way but with no welt, the stitch lying on the insole one side and on the upper the other. Make very solid stitches, pull the last end through to the insole and tie the two ends in a good knot. Take out the four tacks.

Matériaux pour cette étape :

Fibre de chanvreFibre de chanvre1 pièce
Poix de cordonnierPoix de cordonnier1 pièce
Soies de sanglierSoies de sanglier1 pièce

Outils nécessaires :

Alène à coudreAlène à coudre
ManicleManicle
12

Fill the bottom

Rub chalk on the stitches and tap a piece of felt on the insole to mark its size; paste the insole, lay the felt on, hammer it and trim it level with the welt when dry. Peg a piece of good solid leather in the waist with about four pegs, skived thin at the ends and sides, paste it and cover it with thin split felt; add another layer if the bottom is hollow, until it is level with the welt. Rub in powdered French chalk.

Matériaux pour cette étape :

Feutre de laineFeutre de laine1 pièce
Colle de pâte de bléColle de pâte de blé1 pièce
Cuir de harnaisCuir de harnais1 pièce
Chevilles en boisChevilles en bois1 pièce
Craie de Briançon (talc)Craie de Briançon (talc)1 pièce

Outils nécessaires :

Alène à chevillesAlène à chevilles
Marteau à panne fendueMarteau à panne fendue
Couteau à cuirCouteau à cuir
13

Lay the sole

Wet the sole leather, dry it till just mellow, scrape the grain, flesh the back and hammer it from the centre out. Mark it round to the boot and cut off the spare toe piece. Paste the sole's flesh side and the bottom of the boot, chalk the felt, and fix the sole with sole tacks at the toe, at B and two at C. Tap it all over; for an ordinary waist skive the sole's flesh side at the waist, leaving it thicker next the welt; for riding boots it may be left full (a square waist). Run a blunt bone round between upper and welt to set the welt flat.

Matériaux pour cette étape :

Cuir à semellesCuir à semelles1 pièce
Colle de pâte de bléColle de pâte de blé1 pièce
Craie de Briançon (talc)Craie de Briançon (talc)1 pièce
Semences de montageSemences de montage1 pièce

Outils nécessaires :

Couteau à cuirCouteau à cuir
Marteau à panne fendueMarteau à panne fendue
Fer à genouxFer à genoux
Plioir en osPlioir en os
14

Round up and channel the sole

Hold the boot on its side on the knees and pare the sole round to shape with a very sharp knife, the point overhanging the guiding finger only by the sole's thickness, little by little, closer at the toe and wider toward the waist, leaving stuff at the seat; keep the edge even and square. Mark the channel about ¹⁄₁₆ in from the edge in the fore part and about ¼ in in the waist; cut it with the knife at about 50 degrees to the welt, nearly half-way through, and open it with the prick-stitch, throwing the grain back.

Outils nécessaires :

Couteau à cuirCouteau à cuir
Compas à pointes sèchesCompas à pointes sèches
Pique-pointsPique-points
15

Stitch the sole

Make the stitching thread of yellow flax waxed with white wax or beeswax, twisted lighter and wiry. Run the fudge wheel round the welt to mark the stitches. With the strap over the waist, thrust the stitching awl through welt and sole into the channel in one quick, straight jerk, never wriggled, and set each stitch the same way. Rub the stitches down with the bone, paste the channel thinly and lay it down with the smooth side of an old file, trim the burr level, damp the sole and rub it down with the long-stick; hammer it all over.

Matériaux pour cette étape :

Fil de linFil de lin1 pièce
Cire d'abeilleCire d'abeille1 pièce
Soies de sanglierSoies de sanglier1 pièce
Colle de pâte de bléColle de pâte de blé1 pièce
EauEau1 pièce

Outils nécessaires :

Roulette à marquerRoulette à marquer
Alène à piquerAlène à piquer
Lanière de cuirLanière de cuir
Plioir en osPlioir en os
Jeu de limesJeu de limes
Couteau à cuirCouteau à cuir
Lissoir à couturesLissoir à coutures
Marteau à panne fendueMarteau à panne fendue
16

Fit the seat-piece

Cut the seat-piece straight on one edge, file it, paste both pieces, butt the edges, nail at A and peg about five pegs in the seat-piece and two in the sole, about ½ in from the edge. Pare it to shape, overhanging the stitches ¼ in, and take the angle off round for a third or bare half of the thickness. Draw the nail, cut off the peg tops, cut the grain away round them and rasp the top rough.

Matériaux pour cette étape :

Cuir à semellesCuir à semelles1 pièce
Colle de pâte de bléColle de pâte de blé1 pièce
Chevilles en boisChevilles en bois1 pièce

Outils nécessaires :

Jeu de limesJeu de limes
Alène à chevillesAlène à chevilles
Marteau à panne fendueMarteau à panne fendue
Couteau à cuirCouteau à cuir
RâpeRâpe
17

Make the split-lift and first lifts

Cut a piece of first-cut butt leather about 7 in x 1 in and, wet, split it on the slant into two wedge-shaped strips; bend each round on the lap iron and hammer the puckers flat. Rasp and paste the seat and the split-lift, lay it flush at the back of the seat and peg it, the pegs toward the centre; pare it round. Rough and paste the first whole lift, peg it on with about five pegs, rasp it and trim it; lay the second lift with two ¾ in rivets.

Matériaux pour cette étape :

Cuir à semellesCuir à semelles1 pièce
Colle de pâte de bléColle de pâte de blé1 pièce
Chevilles en boisChevilles en bois1 pièce
Rivets de cordonnierRivets de cordonnier1 pièce

Outils nécessaires :

Couteau à cuirCouteau à cuir
Fer à genouxFer à genoux
RâpeRâpe
Alène à chevillesAlène à chevilles
Marteau à panne fendueMarteau à panne fendue
18

Sew down the heel

Cut a V-groove channel in the top lift. Rub the seat with the bone. With a thread four to six strands stouter than sewing thread and the heel awl dipped in soap, sew the heel down from corner to corner, each stitch passing through the loop of the seat stitch, hammering every few stitches, and knot the last. Pene the heel all round with the pene of the hammer to drive the leather over the stitches, trim the seat with the knife and a metal guard, sweep the seat-breaker round, and smooth the edge with a welt file.

Matériaux pour cette étape :

Fibre de chanvreFibre de chanvre1 pièce
Poix de cordonnierPoix de cordonnier1 pièce
Soies de sanglierSoies de sanglier1 pièce
Pain de savonPain de savon1 pièce

Outils nécessaires :

Alène à talonAlène à talon
ManicleManicle
Marteau à panne fendueMarteau à panne fendue
Plioir en osPlioir en os
Couteau à cuirCouteau à cuir
Rogne-emboîtageRogne-emboîtage
Jeu de limesJeu de limes
19

Finish the heel

For a 1¼ in heel add two more lifts and the top piece: rough and paste each, rivet the third lift nearly in the centre, then the last lift, and hold the top piece with headless rivets so it can be rounded. Round it up, longer and squarer on the outside corner; put the remaining rivets in, slanting outward, not near the edge. Check with a straight-edge that the top piece is level with the flat of the sole.

Matériaux pour cette étape :

Cuir à semellesCuir à semelles1 pièce
Colle de pâte de bléColle de pâte de blé1 pièce
Rivets de cordonnierRivets de cordonnier1 pièce

Outils nécessaires :

RâpeRâpe
Marteau à panne fendueMarteau à panne fendue
Couteau à cuirCouteau à cuir
20

Knife up, rasp and buff

Round the top piece, then pare the heel all round with the knife, dropping the hand and raising the knife, going round again and again until no bumps can be felt; a piece of horn or bone between upper and seat guards the upper. Knife up the sole edge, rasp it, damp it and scrape it with the buffing knife, keeping it hollow, and sandpaper.

Matériaux pour cette étape :

Papier abrasifPapier abrasif1 pièce
EauEau1 pièce

Outils nécessaires :

Couteau à cuirCouteau à cuir
RâpeRâpe
Racloir de cordonnierRacloir de cordonnier
Pierre à aiguiserPierre à aiguiser
21

Iron, ink and heel-ball

Warm the irons over a spirit lamp, only just warm, wiping each on a rag. Damp the edges and run the forepart, welt, waist and top-piece irons and the seat wheel round, holding each upright and firm. Rub weak ammonia-and-water on the parts to be blacked, then ink them with shoemaker's ink diluted with an equal part of water; when just dry, iron again. Melt heel-ball over the lamp, dab it on the ironed parts and iron it in with the irons a degree cooler, then rub it off with a cloth to a smooth, even gloss. Fudge or prick up the welt.

Matériaux pour cette étape :

Teinture pour cuirTeinture pour cuir1 pièce
Solution d'ammoniac diluéeSolution d'ammoniac diluée1 pièce
Cire à talons (heel ball)Cire à talons (heel ball)1 pièce
EauEau1 pièce

Outils nécessaires :

Brûleur à alcool (lampe à esprit-de-vin)Brûleur à alcool (lampe à esprit-de-vin)
Fer à lisser les lisièresFer à lisser les lisières
Roulette d'emboîtageRoulette d'emboîtage
Roulette à marquerRoulette à marquer
22

Take out the last and finish inside

Take out the block screw, hook the last hook into its hole over the heel, put your feet on the handle and pull the boot off. Paste a seat-sock on its wrong side to within ⅛ in of the edge and put it in. Tap the insole feather down lightly on either side with a smooth-headed hammer. A thin coat of weak paste and a first blacking, sleeked with bone while on the last, save trouble in cleaning calf.

Matériaux pour cette étape :

Cuir de veauCuir de veau1 pièce
Colle de pâte de bléColle de pâte de blé1 pièce

Outils nécessaires :

Crochet à formeCrochet à forme
Marteau à panne fendueMarteau à panne fendue
Plioir en osPlioir en os
23

Troubleshooting

Welted boot troubleshooting.

Flow

Loading...
24

History and honest limits

From **Boot Making and Mending**, edited by Paul N. Hasluck, Cassell and Company, London, 1898 (Project Gutenberg #78854), chapters IV-VIII. His lasting chapter describes a laced boot; here the upper is the Wellington leg of the previous blueprint. Not made here: the pegged seat and waist, the flexura steel waist spring, riveted work, and the black, buff and white bottom finishes beyond the edges. All sizes are his; the metric figures are ours.

Matériaux

23

Outils requis

30

CC0 Domaine public

Ce blueprint est publié sous CC0. Vous êtes libre de copier, modifier, distribuer et utiliser ce travail pour tout usage, sans demander la permission.

Soutenez le Maker en achetant des produits via son Blueprint où il perçoit une Commission Maker définie par les Vendeurs, ou créez une nouvelle itération de ce Blueprint et incluez-le comme connexion dans votre propre Blueprint pour partager les revenus.

Commentaires

(0)

Se connecter pour participer à la discussion

Chargement des commentaires...