Collaboration
ART
BEAUTÉ ET BIEN-ÊTRE
ARTISANAT
CULTURE ET HISTOIRE
DIVERTISSEMENT
ENVIRONNEMENT
NOURRITURE ET BOISSONS
INGÉNIERIE INVERSE
SCIENCES
SPORTS
TECHNOLOGIE
TECHNOLOGIE PORTABLE
Leader Harness Long Crupper: Folded Dock, Lay, Hip Straps, Carrier Straps and Tugs (Hasluck, Harness Making, 1904)
Tex

Créé par

Tex

13. novembre 2026FO
9
0
0
0
0

Leader Harness Long Crupper: Folded Dock, Lay, Hip Straps, Carrier Straps and Tugs (Hasluck, Harness Making, 1904)

The leader horse's long crupper (F in Fig. 102) runs from the collar straps along the back to the tail, and carries the hip straps (H) that hold up the chain traces and the carrier straps (L) for the stretcher. This is the long crupper from Paul N. Hasluck's Harness Making (1904), with its folded dock, lay, 3 in dee, hip-strap tugs (K) and stretcher strap (M). Every size is his.
Avancé
About 1-2 days

Consignes

1

His sizes in centimetres

Chargement du notebook Jupyter…
2

Read Harness Making, ch. VIII

"Cut the crupper from good leather 3 ft. 8 in. long and 5 in. wide, and make a split 9 in. long at the light end and another, 7 in. long, at the tail end."
3

Cut the body

Cut the crupper 3 ft 8 in by 5 in. Slit the light end 9 in and the tail end 7 in, leaving the points of the slits the full width in front and only cutting a little out of the corners. Narrow the tail-end points gradually to about 1-1/8 in and cut a little from the sides of each slit. Cut a lining for a foot or so of the tail end.

Matériaux pour cette étape :

Cuir de harnaisCuir de harnais1 pièce

Outils nécessaires :

Couteau à cuirCouteau à cuir
Mètre rubanMètre ruban
4

Fold the dock

Cut soft leather 16 in by 3-1/2 in for the dock and shave the ends thin. Damp it well and turn both edges down so they overlap deeply along the centre. Bring both ends together, sides meeting flat but not flat sides together; holding the piece flat in the centre, turn the lower edge inwards and upwards, keeping the points together with the other hand. Nail each point to a board and keep it in shape until dry, when the dock will be firm.

Matériaux pour cette étape :

BasaneBasane1 pièce
ClousClous1 pièce

Outils nécessaires :

Couteau à cuirCouteau à cuir
ÉpongeÉponge
MarteauMarteau
Planche de pinPlanche de pin
5

Finish the body and put in the dock

Edge, crease and black the body, making two rows all round; rub the edges well and hot-crease the lines. At the tail end prick the second line as far as the double runs. When the dock is dry, put it between the lining and body at each end of the slit, tack it down round the lining and stitch. A few egg-shaped stitches inside the outer stitches, through the body and dock points, keep the dock in place. Trim the edges and black, rub and tallow them, and the inside edges of the slits too.

Matériaux pour cette étape :

Teinture pour cuirTeinture pour cuir1 pièce
SuifSuif1 pièce
Semences de montageSemences de montage1 pièce
Fil de cuirFil de cuir1 pièce
Cire d'abeilleCire d'abeille1 pièce

Outils nécessaires :

Abat-carreAbat-carre
PlioirPlioir
Chalumeau à propaneChalumeau à propane
Lissoir à arêtes de cuirLissoir à arêtes de cuir
Griffe à frapperGriffe à frapper
MarteauMarteau
AlêneAlêne
Deux aiguilles de sellierDeux aiguilles de sellier
Pince de sellierPince de sellier
6

Fit the front buckles

Cut two chapes to hold the buckles in front that fasten the crupper to the collar straps; bend them down about 4 in, shave one end and point the other, and cut a hole for the buckle. Tack two loops about 1-1/2 in wide in place, keeping the outside of each buckle exactly level with the end of its slit and the chapes right in the centre. Stitch them down, put a cross stitch on each side of the buckle, and shape and crease the loops.

Matériaux pour cette étape :

Cuir de harnaisCuir de harnais1 pièce
Boucle en fer à ardillonBoucle en fer à ardillon2 pièces
Fil de cuirFil de cuir1 pièce
Cire d'abeilleCire d'abeille1 pièce

Outils nécessaires :

Couteau à cuirCouteau à cuir
Mandrin à passantsMandrin à passants
PlioirPlioir
Chalumeau à propaneChalumeau à propane
AlêneAlêne
Deux aiguilles de sellierDeux aiguilles de sellier
Pince de sellierPince de sellier
7

Make the lay, hip straps and carrier straps

Cut the lay 1 ft 3 in by 3 in, turn it down for about 1 ft at the good end, shave the end of the short turn thin and round the other end; edge, crease and black it. Cut two hip straps 2 ft by 1-1/2 in, turn them down 3 in at the heavy end, shave the turn-down, point the buckle end, and crease and black them. Attach them to a 3 in japanned or tinned dee, one on each side, with four rows of stitching in the double of each; rub and finish the edge. Make two carrier straps the same way, each 2 ft 10 in by 1-1/4 in, and stitch them in the middle round part of the dee between the hip straps.

Matériaux pour cette étape :

Cuir de harnaisCuir de harnais1 pièce
Dé de harnaisDé de harnais1 pièce
Teinture pour cuirTeinture pour cuir1 pièce
Fil de cuirFil de cuir1 pièce
Cire d'abeilleCire d'abeille1 pièce

Outils nécessaires :

Couteau à cuirCouteau à cuir
Abat-carreAbat-carre
PlioirPlioir
Chalumeau à propaneChalumeau à propane
Lissoir à arêtes de cuirLissoir à arêtes de cuir
AlêneAlêne
Deux aiguilles de sellierDeux aiguilles de sellier
Pince de sellierPince de sellier
Mètre rubanMètre ruban
8

Stitch the dee and lay to the body

Put the straight part of the dee in the bend of the lay and place it on the centre of the crupper body, the same distance from each side, with the extreme point of the dee within 8 in of the points of the tail slits. Tack down and stitch two rows 1/4 in apart all round, eight per inch, with three-cord thread; then stitch the lay coarse, or spot it across just to the dee. Some makers put a pad under the crupper, as on the cart-saddle crupper, from the end of the tail slit to 1 in beyond the point of the lay.

Matériaux pour cette étape :

Semences de montageSemences de montage1 pièce
Fil de cuirFil de cuir1 pièce
Cire d'abeilleCire d'abeille1 pièce

Outils nécessaires :

MarteauMarteau
Griffe à frapperGriffe à frapper
AlêneAlêne
Deux aiguilles de sellierDeux aiguilles de sellier
Pince de sellierPince de sellier
9

Make the hip-strap tugs and stretcher strap

With a pair of 1-1/2 in hip-strap chains, cut the tugs 10 in by 1-1/2 in; bend them so the points meet in the centre, cut a hole for the buckle in one end, stitch the points together and put in two narrow loops (one hides the joint) or one broad loop. Stitch a safe underneath. For the stretcher carrier tug, cut a strap 1-1/4 in by 1 ft 2 in, bend a chape in it and cut a hole for the buckle; stitch the buckle on with a loop, and make a running loop and a hole 1 in from the point of the strap.

Matériaux pour cette étape :

Chaîne en ferChaîne en fer2 pièces
Cuir de harnaisCuir de harnais1 pièce
Boucle en fer à ardillonBoucle en fer à ardillon3 pièces
Fil de cuirFil de cuir1 pièce
Cire d'abeilleCire d'abeille1 pièce

Outils nécessaires :

Couteau à cuirCouteau à cuir
Mandrin à passantsMandrin à passants
Emporte-pièce pour cuirEmporte-pièce pour cuir
AlêneAlêne
Deux aiguilles de sellierDeux aiguilles de sellier
Pince de sellierPince de sellier
10

Put the gear together

Fix a loop on each end of the stretcher and nail its ends, leaving room for the strap to pass. Put the runner loop on the strap, run the strap down through the stretcher loop and back through the runner to the buckle; secure the carrier straps to the same buckle, their points down in the loop, and keep the runner down by the stretcher. Buckle the hip straps into the tug buckles, hook the chain traces on, and buckle the collar straps into the front buckles. The dock under the tail is optional: the hip straps fastened in the dee keep the crupper in place.

Matériaux pour cette étape :

Cuir de harnaisCuir de harnais1 pièce
ClousClous1 pièce

Outils nécessaires :

MarteauMarteau
Couteau à cuirCouteau à cuir
11

Troubleshooting

Long crupper troubleshooting.

Flow

Loading...
12

History and honest limits

From **Harness Making**, edited by Paul N. Hasluck, Cassell, 1904 (Project Gutenberg 70169), chapter VIII, "Fore Gear or Leader Harness", pp. 101-104, Figs. 102-104; every fraction was checked on the archive.org scan (harnessmaking00hasl). The stretcher (the bar that keeps the traces apart) is not made here. Basil for the "soft leather" dock, the buckle count in the list, the tools and metric figures are ours.

Matériaux

11

Outils requis

15

CC0 Domaine public

Ce blueprint est publié sous CC0. Vous êtes libre de copier, modifier, distribuer et utiliser ce travail pour tout usage, sans demander la permission.

Soutenez le Maker en achetant des produits via son Blueprint où il perçoit une Commission Maker définie par les Vendeurs, ou créez une nouvelle itération de ce Blueprint et incluez-le comme connexion dans votre propre Blueprint pour partager les revenus.

Commentaires

(0)

Se connecter pour participer à la discussion

Chargement des commentaires...