Collaboration
ART
BEAUTÉ ET BIEN-ÊTRE
ARTISANAT
CULTURE ET HISTOIRE
DIVERTISSEMENT
ENVIRONNEMENT
NOURRITURE ET BOISSONS
INGÉNIERIE INVERSE
SCIENCES
SPORTS
TECHNOLOGIE
TECHNOLOGIE PORTABLE
Plough Back-Band With Hooks: Faced, Flock-Padded Back-Band With a Rein Dee (Hasluck, Harness Making, 1904)
Tex

Créé par

Tex

13. novembre 2026FO
7
0
0
0
0

Plough Back-Band With Hooks: Faced, Flock-Padded Back-Band With a Rein Dee (Hasluck, Harness Making, 1904)

In plough harness the back-band carries the traces over the horse's back. This is the plough back-band with hooks from Paul N. Hasluck's Harness Making (1904): a 4 in band about 4 ft 4 in over all, with leather facings, a flock-stuffed panel to stop the back getting sore, a dee for the plough rein, and a hook sewn into each end. Every size is his; the picture is our diagram with his Fig. 105 inset.
Intermédiaire
About 1 day

Consignes

1

His sizes in centimetres

Chargement du notebook Jupyter…
2

Read Harness Making, ch. IX

"In plough gears the ordinary bridle and collar are employed. The back-band is made in various ways. The method with hooks is taken first. The eye of the hook (Fig. 105) is 4 in. wide."
3

Cut and mark the back-band

Cut the leather 3 ft 9 in long and 4 in wide. Turn down 3 in at each end, beat the bend slightly with the hammer to keep it down, and crease it with the screw race, two rows on each side. Mark the centre from each end and draw a line straight across there, then two lines 5 in each side of the centre, 10 in apart.

Matériaux pour cette étape :

Cuir de harnaisCuir de harnais1 pièce

Outils nécessaires :

Couteau à cuirCouteau à cuir
MarteauMarteau
PlioirPlioir
Chalumeau à propaneChalumeau à propane
CrayonCrayon
Mètre rubanMètre ruban
4

Stitch on the facings

Cut two pieces 10-1/2 in long and 3/4 in wide; cut a small piece out of each corner of the working side, then dye and crease that side. Draw a line along the centre of each with the compasses and mark across the centre. Prick out where they go on the back-band, then place one underneath the back-band, centre to centre, as far as the drawn line, and tack it down; place the other the same way on the other side, so the pieces run a little over both lower lines at each end. Stitch, keeping the line close to the edge of the back-band, with thread of three or four cords of coarse hemp.

Matériaux pour cette étape :

Cuir de harnaisCuir de harnais1 pièce
Teinture pour cuirTeinture pour cuir1 pièce
Semences de montageSemences de montage1 pièce
Ficelle de chanvreFicelle de chanvre1 pièce
Cire d'abeilleCire d'abeille1 pièce

Outils nécessaires :

Couteau à cuirCouteau à cuir
PlioirPlioir
Compas à rainer de sellierCompas à rainer de sellier
Griffe à frapperGriffe à frapper
MarteauMarteau
AlêneAlêne
Deux aiguilles de sellierDeux aiguilles de sellier
Pince de sellierPince de sellier
5

Fit the rein dee

Cut a piece of leather 1-1/2 in by 4 in, shave and point both ends, and crease, black and prick it like the side, eight or ten marks per inch. Put a 1-1/2 in tinned dee in the centre of it, lay it flat on the back-band in the centre (measured from both sides, or from the top line to either line below), tack it and stitch. The plough rein runs through this dee; for a pair of horses put the dee on the opposite side of each back-band, for a single horse one on each side of the same back-band.

Matériaux pour cette étape :

Dé de harnaisDé de harnais1 pièce
Cuir de harnaisCuir de harnais1 pièce
Teinture pour cuirTeinture pour cuir1 pièce
Ficelle de chanvreFicelle de chanvre1 pièce
Cire d'abeilleCire d'abeille1 pièce

Outils nécessaires :

Couteau à cuirCouteau à cuir
Griffe à frapperGriffe à frapper
AlêneAlêne
Deux aiguilles de sellierDeux aiguilles de sellier
Pince de sellierPince de sellier
6

Make the panel

Take linen (or basil) 14 in by 7 in and lay the back-band on it centre to centre, even on both sides. Spot-stitch across the back-band and through the linen along the middle line, like this: // // //. Turn in the linen all round about 1/2 in (basil needs no turning). Make a pleat at each corner at the end of the facing, both exactly the same length, and another opposite each, so the width equals the back-band and facing together (for basil, cut the corner off and stitch the cut instead). Stitch all round, starting about 1-1/2 in from the centre on one side to leave an opening for stuffing, along the cross lines at the bottom, to within 1-1/2 in of the centre on the other side.

Matériaux pour cette étape :

Toile de linToile de lin1 pièce
Ficelle de chanvreFicelle de chanvre1 pièce
Cire d'abeilleCire d'abeille1 pièce

Outils nécessaires :

CiseauxCiseaux
AlêneAlêne
Deux aiguilles de sellierDeux aiguilles de sellier
7

Stuff the panel

Lay the back-band flat on the bench, leather side underneath, openings near the bench edge. Stuff each side rather tightly with flock through the openings, using the stuffing stick; smooth it well towards the sides, flatten with a mallet, and stitch along the openings to the starting point.

Matériaux pour cette étape :

Bourre de laineBourre de laine1 pièce
Ficelle de chanvreFicelle de chanvre1 pièce
Cire d'abeilleCire d'abeille1 pièce

Outils nécessaires :

Bourroir de sellierBourroir de sellier
Maillet en boisMaillet en bois
AlêneAlêne
Deux aiguilles de sellierDeux aiguilles de sellier
8

Sew in the hooks

Cut two saving pieces from a thick, firm face of hide (the face of a gear hide is best), 7 in long and, for a 4 in back-band, 5 in wide. Cut one end slanting to 4 in, the back-band's width, and shave it; round the corners of the other end, leaving it full width; black and crease the edges. Put the hooks in place with the saving pieces under them about 1-1/2 in lower than the end of the hook, and tack them down exactly in the centre. Mark and prick four rows from the hook up to the end of the saving pieces, stitch with four-cord thread, nine or ten stitches per inch, and stitch a line across close to the hook to bind it all together.

Matériaux pour cette étape :

Crochet de dossièreCrochet de dossière2 pièces
Cuir de harnaisCuir de harnais1 pièce
Teinture pour cuirTeinture pour cuir1 pièce
Semences de montageSemences de montage1 pièce
Ficelle de chanvreFicelle de chanvre1 pièce
Cire d'abeilleCire d'abeille1 pièce

Outils nécessaires :

Couteau à cuirCouteau à cuir
PlioirPlioir
Chalumeau à propaneChalumeau à propane
Griffe à frapperGriffe à frapper
MarteauMarteau
AlêneAlêne
Deux aiguilles de sellierDeux aiguilles de sellier
Pince de sellierPince de sellier
9

Troubleshooting

Plough back-band troubleshooting.

Flow

Loading...
10

History and honest limits

From **Harness Making**, edited by Paul N. Hasluck, Cassell, 1904 (Project Gutenberg 70169), chapter IX, "Plough Harness", pp. 107-110, Fig. 105; every fraction was checked on the archive.org scan (harnessmaking00hasl). The back-band with chains instead of hooks and the coupling straps are not made here. Linen for the panel (he allows basil), the tools and metric figures are ours; the picture is our diagram with his Fig. 105 inset.

Matériaux

9

Outils requis

14

CC0 Domaine public

Ce blueprint est publié sous CC0. Vous êtes libre de copier, modifier, distribuer et utiliser ce travail pour tout usage, sans demander la permission.

Soutenez le Maker en achetant des produits via son Blueprint où il perçoit une Commission Maker définie par les Vendeurs, ou créez une nouvelle itération de ce Blueprint et incluez-le comme connexion dans votre propre Blueprint pour partager les revenus.

Commentaires

(0)

Se connecter pour participer à la discussion

Chargement des commentaires...