Collaboration
ART
BEAUTÉ ET BIEN-ÊTRE
ARTISANAT
CULTURE ET HISTOIRE
DIVERTISSEMENT
ENVIRONNEMENT
NOURRITURE ET BOISSONS
INGÉNIERIE INVERSE
SCIENCES
SPORTS
TECHNOLOGIE
TECHNOLOGIE PORTABLE
Cam-Arm Tubing Cutter: Two Swinging Arms Keep the Wheel and Rollers Evenly Round Any Tube (Lutsker, 1959)
Forge

Créé par

Forge

13. novembre 2026NO
9
0
0
0
0

Cam-Arm Tubing Cutter: Two Swinging Arms Keep the Wheel and Rollers Evenly Round Any Tube (Lutsker, 1959)

Simon Lutsker of Shaker Heights, Ohio, received US 2,870,536, dated 27 January 1959, for a tubing cutter that grips small and large tubes equally well. The wheel turns under a housing at the foot of a guide. A block slides up the guide on a screw. Two arms hang from the block, each with a roller at its lower end. Springs press the arms' curved cam edges against rollers on the housing. As the screw draws the block up, the arms swing inwards or outwards, so the wheel and the two rollers stay about evenly spaced round the tube, whatever its size. We worked out the cam so the three contacts are exactly 120 degrees apart. The curve comes out as an arc, as in his patent. All sizes are ours.
Avancé
About 4 days

Consignes

1

Three points evenly round

Chargement du notebook Jupyter…
2

Read US 2,870,536

"Irrespective of the size of the tubing which is being cut, the points of engagement of the cutter wheel 21 and support rollers 32 with the tubing will always be substantially equidistant from each other circumferentially of the tubing."
3

Print the template

The arm plate with its cam edge, the housing and the guide block at 1:1, with holes, slots and sizes. print at 100 % (check the 50 mm bar).
Fichier de designPDFCC0 - Free
4

Cut the arm plates

Glue four copies of the arm outline on 3 mm steel plate. Saw and file them to the line, taking the cam edge slowly and checking it against the template. Clamp them in a stack and drill the 4 mm pivot and roller-pin holes and the two 3 mm holes through all four together.

Matériaux pour cette étape :

Plaque d'acier douxPlaque d'acier doux1 pièce

Outils nécessaires :

Scie à métauxScie à métaux
Jeu de limesJeu de limes
Jeu de limes aiguillesJeu de limes aiguilles
Perceuse à colonnePerceuse à colonne
Étau de machineÉtau de machine
Jeu de foretsJeu de forets
PointeauPointeau
Étau d'établiÉtau d'établi
Pied à coulisse numérique 6 poucesPied à coulisse numérique 6 pouces
5

Make the housing

From 30 x 20 flat bar, saw a block 64 mm long and file it to 28 x 18 mm, leaving the two ears below its middle. Saw the forked ends: two cuts 14.4 mm apart, 20 mm in from each end, and break out the middle. Saw and file a 7 mm slot up between the ears for the wheel. Drill the 5 mm shaft hole across the ears, the 4 mm housing-roller pins across the forks, and the 4 mm rivet hole. File a groove 20 mm wide and 3 mm deep down each face for the guide's legs.

Matériaux pour cette étape :

Plat en acier douxPlat en acier doux1 pièce

Outils nécessaires :

Scie à métauxScie à métaux
Jeu de limesJeu de limes
Perceuse à colonnePerceuse à colonne
Étau de machineÉtau de machine
Jeu de foretsJeu de forets
Étau d'établiÉtau d'établi
Pied à coulisse numérique 6 poucesPied à coulisse numérique 6 pouces
Pointe à tracerPointe à tracer
6

Make the block and the guide

Saw the guide block from the same bar, 60 x 18 x 28 mm, with forked ends from 14 mm out, the 4 mm pivot holes, the 3 mm spring-pin holes and the leg grooves. Drill 8.5 mm up its middle and tap M10. Bend a 20 x 3 mm flat bar into an inverted U with its legs 22 mm apart inside and 69 mm high, and drill a 10.5 mm hole in its top.

Matériaux pour cette étape :

Plat en acier douxPlat en acier doux2 pièces

Outils nécessaires :

Scie à métauxScie à métaux
Jeu de limesJeu de limes
Perceuse à colonnePerceuse à colonne
Étau de machineÉtau de machine
Jeu de foretsJeu de forets
Jeu de tarauds et filièresJeu de tarauds et filières
Étau d'établiÉtau d'établi
Marteau à panne bombéeMarteau à panne bombée
Pied à coulisse numérique 6 poucesPied à coulisse numérique 6 pouces
7

Turn the rollers and the wheel shaft

Turn two housing rollers 10 mm across and 14 mm long, and two lower rollers 12 mm across and 7.6 mm long, from mild steel bar, all bored 4.2 mm. For the wheel shaft, turn a 6 mm rod to 5 mm, leaving a 6 mm head, file a flat on the head, and turn a groove near the other end.

Matériaux pour cette étape :

Barre ronde en acier douxBarre ronde en acier doux1 pièce
Rond en acier douxRond en acier doux1 pièce

Outils nécessaires :

Tour à métauxTour à métaux
Mandrin de tour à 3 morsMandrin de tour à 3 mors
Outil de coupe pour tourOutil de coupe pour tour
Bédane de tronçonnageBédane de tronçonnage
Jeu de foretsJeu de forets
Jeu de limesJeu de limes
Pied à coulisse numérique 6 poucesPied à coulisse numérique 6 pouces
8

Turn the cutting wheel

Chuck a tool steel bar and face it. Turn the end to 20 mm across for 10 mm, centre drill and drill a 5 mm hole 10 mm deep, and turn the edge to a 50 degree vee, 25 degrees each side, sharp in the middle of the 6 mm width. Part it off 6 mm long and take the burr off the hole.

Matériaux pour cette étape :

Barre d'acier à outilsBarre d'acier à outils1 pièce

Outils nécessaires :

Tour à métauxTour à métaux
Mandrin de tour à 3 morsMandrin de tour à 3 mors
Outil de coupe pour tourOutil de coupe pour tour
Bédane de tronçonnageBédane de tronçonnage
Jeu de forets à centrerJeu de forets à centrer
Jeu de foretsJeu de forets
Pied à coulisse numérique 6 poucesPied à coulisse numérique 6 pouces
Lunettes de sécuritéLunettes de sécurité
9

Harden and temper

Heat the wheel to a cherry red, until a magnet no longer sticks, and quench it in water, moving it about. Rub it bright with a stone, warm it on a piece of steel plate over the fire, and quench again as soon as it turns a light straw colour.

Outils nécessaires :

ForgeForge
Tenailles de forgeTenailles de forge
Petit aimantPetit aimant
Baquet de trempeBaquet de trempe
EauEau
Pierre à aiguiserPierre à aiguiser
Gants de soudeurGants de soudeur
Lunettes de sécuritéLunettes de sécurité
10

Make the springs

From spring steel strip, cut two strips 8 mm wide and 30 mm long for the arm springs, and one 6 mm wide and 25 mm long to hold the wheel shaft. Bend each arm spring so it presses on its arm's spring pin and pushes the arm outwards. Drill a hole in the end of each for its pin or screw.

Matériaux pour cette étape :

Feuillard d'acier à ressortFeuillard d'acier à ressort1 pièce

Outils nécessaires :

Scie à métauxScie à métaux
Jeu de limesJeu de limes
Perceuse à colonnePerceuse à colonne
Jeu de foretsJeu de forets
Étau d'établiÉtau d'établi
11

Make the screw

Cut 90 mm of M10 threaded rod. Lock two nuts together 25 mm from its top as the flange. Put it up through the guide's top hole, add two washers as the spacer, then a nut locked with a second one. Drill a 6 mm hole across the top end and fit a 70 mm piece of 6 mm rod as the T-handle.

Matériaux pour cette étape :

Tige filetéeTige filetée1 pièce
Écrou hexagonalÉcrou hexagonal4 pièces
Rondelle plateRondelle plate2 pièces
Rond en acier douxRond en acier doux1 pièce

Outils nécessaires :

Clé à moletteClé à molette
Perceuse à colonnePerceuse à colonne
Jeu de foretsJeu de forets
Scie à métauxScie à métaux
Marteau à panne bombéeMarteau à panne bombée
12

Assemble

Pin each arm pair together with its lower roller between the plates, and with short tubes as spacers on the pivot and spacer pins. Pin the arms into the block's forked ends. Fit the housing rollers in the housing's forks and the wheel on its shaft, with the flat spring screwed to the housing and sitting in the shaft's groove. Screw the block onto the screw, feed the arms down through the housing's forks inside its rollers, and rivet the guide's legs into the housing's grooves. Pin the arm springs to the block. Oil every pin and the screw.

Matériaux pour cette étape :

Goupille cylindrique en acierGoupille cylindrique en acier8 pièces
Rivets en acierRivets en acier1 pièce
Vis à tête cylindrique à six pans creuxVis à tête cylindrique à six pans creux1 pièce

Outils nécessaires :

Marteau à panne bombéeMarteau à panne bombée
PointeauPointeau
Étau d'établiÉtau d'établi
Jeu de clés AllenJeu de clés Allen
Huile de coupeHuile de coupe
13

Cut a copper tube

Mark a copper tube and hold it in a vice with soft jaws, or by hand for small tubes. Turn the handle to open the arms, put the cutter over the tube, and turn it back until the rollers lift the tube against the wheel. Check by eye that the wheel and rollers look evenly spaced. Turn the cutter once round, give the screw about a quarter turn, and go on until the tube parts. The wheel should run in its own groove; the end should be square and not squeezed oval. Clean the inside of the end with a deburring tool.

Matériaux pour cette étape :

Tube de cuivreTube de cuivre1 pièce

Outils nécessaires :

Étau d'établiÉtau d'établi
ÉbavureurÉbavureur
Pied à coulisse numérique 6 poucesPied à coulisse numérique 6 pouces
14

Troubleshooting

Cam-arm tubing cutter troubleshooting.

Flow

Loading...
15

History and honest limits

**Simon Lutsker** of Shaker Heights, Ohio, US 2,870,536, dated 27 January 1959, filed 26 August 1957. He claimed "a guide block mounted for movement along said guide member and movable by said screw means, a pair of cammable members pivotally secured to said guide block" and the springs pressing their "arcuate cam surfaces" against the housing rollers. He said the contacts stay "substantially" equidistant; ours are set exactly 120 degrees apart. The patent gives no sizes or cam radius; all of ours are ours.

Matériaux

13

Outils requis

29

Fichiers de conception

1

CC0 Domaine public

Ce blueprint est publié sous CC0. Vous êtes libre de copier, modifier, distribuer et utiliser ce travail pour tout usage, sans demander la permission.

Soutenez le Maker en achetant des produits via son Blueprint où il perçoit une Commission Maker définie par les Vendeurs, ou créez une nouvelle itération de ce Blueprint et incluez-le comme connexion dans votre propre Blueprint pour partager les revenus.

Commentaires

(0)

Se connecter pour participer à la discussion

Chargement des commentaires...