ART
BEAUTÉ ET BIEN-ÊTRE
ARTISANAT
CULTURE ET HISTOIRE
DIVERTISSEMENT
ENVIRONNEMENT
NOURRITURE ET BOISSONS
AVENIR VERT
INGÉNIERIE INVERSE
SCHOOL PROJECTS
SCIENCES
SPORTS
TECHNOLOGIE
TECHNOLOGIE PORTABLE
Building Leonardo da Vinci's Self-Propelled Cart — The First Programmable Robot
Around 1478 Leonardo da Vinci designed a cart that drives itself: no ox, no push, no rider. Coiled springs store the power, wooden gears carry it to the wheels, an escapement doles it out evenly, and pegs set into a control wheel steer the cart along a route decided in advance. It is spring power, gear reduction, escapement timing and programmable control in one machine — an ancestor of both the automobile and the robot. In 2004 a museum in Florence built it to his drawings and it ran exactly as designed. This blueprint reconstructs that remarkable machine.
Avancé
30
Consignes
1
1
Understand the machine
Understand the machine
Leonardo's cart carries its own power source and steers itself. Wound springs drive it, gears set the speed, an escapement keeps it steady, and pegs on a control wheel turn it left or right on cue. Often called the first robot, it was reconstructed in Florence in 2004 and ran just as he drew it.
2
2
Build the frame and wheels
Build the frame and wheels
Build a low, sturdy wooden frame carrying an axle front and rear. Cut round wheels and mount them so they turn freely, and bore the axle bearings cleanly so there is little friction to waste the spring's energy.
Matériaux pour cette étape :
Beech Lumber3 piècesOutils nécessaires :
Hand Saw
Hand Auger3
3
Make the coiled springs
Make the coiled springs
The power comes from two coiled leaf springs set in drums beneath the frame. Winding them stores energy; as they slowly unwind they turn the drive. This clockwork-style spring drive — not a falling weight — is Leonardo's key idea.
Matériaux pour cette étape :
Leaf Spring2 piècesOutils nécessaires :
Wooden Mallet4
4
Cut and fit the wooden gears
Cut and fit the wooden gears
Cut cogged wooden gearwheels that take the drive from the spring drums and gear it down to the road wheels, so the stored energy is delivered at a slow, steady, useful speed instead of one violent burst.
Matériaux pour cette étape :
Wooden Gear4 piècesOutils nécessaires :
Gouge
Knife5
5
Add the escapement
Add the escapement
Fit an escapement — the same regulating trick used in clocks — between the springs and the gears. It releases the spring's energy in small, even steps, keeping the cart's speed controlled rather than letting it bolt and stop.
Matériaux pour cette étape :
Wooden Gear1 pièceOutils nécessaires :
Knife6
6
Build the programmable steering
Build the programmable steering
Set removable pegs into a horizontal control wheel geared to the drive. As that wheel turns, each peg nudges the steering to a preset angle, so the cart follows a path you program in advance by where you place the pegs — turn the pegs, change the route.
Matériaux pour cette étape :
Beech Lumber1 pièce
Binding Rope5 mètresOutils nécessaires :
Hand Auger7
7
Wind, set down, release
Wind, set down, release
Wind the springs to store energy, place the cart on the floor, and release the catch. It rolls away under its own power and steers itself left and right exactly as the pegs command, with no one touching it.
8
8
See why it was centuries ahead
See why it was centuries ahead
Spring power, gear reduction, escapement regulation and programmable control together in one device — roughly 400 years before the automobile and the programmable machine. The 2004 Florence reconstruction proved these were not fantasies: Leonardo's cart genuinely works.
Matériaux
4- 4 piècesEspace réservé
- 2 piècesEspace réservé
- 5 piècesEspace réservé
- 5 mètresEspace réservé
Matériaux des Blueprints connectés
You can swap these in
Can't get one of the materials? Swap it for an equivalent — these work just as well.
- Instead of Beech Lumber, try:
Yellow Birch Lumber
Western Hemlock Lumber - Instead of Knife, try:
Gilder's Knife
Blunt Collection Knife
Sharp Cinnamon Knife - Instead of Hand Saw, try:
Portable Band Saw
Band Saw (9-inch, Benchtop)
Miter Box with Saw
Small Hand Saw - Instead of Binding Rope, try:
Lowering Rope
Heavy-Duty Rope - Instead of Wooden Mallet, try:
Rubber Mallet
Blueprints liés
Ces blueprints partagent des connaissances — techniques, matériaux ou principes
Related blueprints
Other builds that share materials, tools, or techniques with this one.
Building Leonardo da Vinci's Armored Car — The Ancestor of the Tank
Building Leonardo da Vinci's Aerial Screw — The Ancestor of the Helicopter
Building Leonardo da Vinci's Parachute — The Sealed Linen Pyramid of 1485
Building Leonardo da Vinci's Revolving Bridge — The Swing Bridge for a Marching Army
Building Leonardo da Vinci's Ornithopter — The Flapping-Wing Flying Machine
Building a Roman Ballista — The Torsion-Powered Bolt Throwerengineering
CC0 Domaine public
Ce blueprint est publié sous CC0. Vous êtes libre de copier, modifier, distribuer et utiliser ce travail pour tout usage, sans demander la permission.
Soutenez le Maker en achetant des produits via son Blueprint où il perçoit une Commission Maker définie par les Vendeurs, ou créez une nouvelle itération de ce Blueprint et incluez-le comme connexion dans votre propre Blueprint pour partager les revenus.