Collaboration
ART
BEAUTÉ ET BIEN-ÊTRE
ARTISANAT
CULTURE ET HISTOIRE
DIVERTISSEMENT
ENVIRONNEMENT
NOURRITURE ET BOISSONS
INGÉNIERIE INVERSE
SCIENCES
SPORTS
TECHNOLOGIE
TECHNOLOGIE PORTABLE
Valentine and Sweets Box: a Card Tray Stacked on a Candy Tray, With Wings That Hold the Card (Richter, 1908)
Tex

Créé par

Tex

13. novembre 2026FO
9
0
0
0
0

Valentine and Sweets Box: a Card Tray Stacked on a Candy Tray, With Wings That Hold the Card (Richter, 1908)

Harry Richter of Omaha received US 901,476, dated 20 October 1908, for a box with two trays under one lid: sweets below, and above them a deeper tray for a valentine, held flat by little card wings so it never touches the lid. The trays stack on an inner rim and cannot slide, and come apart easily. We make it from pasteboard and card. All sizes are ours.
Débutant
About 3 hours

Consignes

1

Box sizes

Chargement du notebook Jupyter…
2

Read US 901,476

"The device affords a secure housing for these articles, and by reason of the formation and arrangement of parts, it may be economically constructed."
3

Make the lower tray

Cut the bottom 1 from pasteboard and glue an upturned rim 3 round it from a card strip, scored and folded at the corners. Glue a second strip inside it, his sustaining leaf 4, standing about 6 mm (ours) above the rim all round.

Matériaux pour cette étape :

Carton contrecolléCarton contrecollé1 pièce
Papier cartonnéPapier cartonné1 pièce
ColleColle1 pièce

Outils nécessaires :

CrayonCrayon
RègleRègle
Cutter de précisionCutter de précision
Plioir en osPlioir en os
Pinceau à collePinceau à colle
4

Make the upper tray

Cut the bottom 6 the same size and glue a deeper rim 8 round it. Glue an enclosing strip 9 round the outside of rim 8, a little lower than it at the top and reaching about 6 mm below the bottom (his portion 10), so the upper tray sits on the lower one with the enclosing strip round the lower tray's inner rim.

Matériaux pour cette étape :

Carton contrecolléCarton contrecollé1 pièce
Papier cartonnéPapier cartonné1 pièce
ColleColle1 pièce

Outils nécessaires :

RègleRègle
Cutter de précisionCutter de précision
Plioir en osPlioir en os
Pinceau à collePinceau à colle
5

Make the card wings

Cut two small triangular card wings, each with a folded flange 16. Glue the flanges inside rim 8, midway between the ends, one each side, so the wings can be bent down over the bottom: their lower edges 17 press on the valentine and keep it off the lid.

Matériaux pour cette étape :

Papier cartonnéPapier cartonné1 pièce
ColleColle1 pièce

Outils nécessaires :

Cutter de précisionCutter de précision
Plioir en osPlioir en os
Pinceau à collePinceau à colle
6

Make the lid

Cut the top leaf 11 to fit over the upper tray and glue a rim 13 round it, sized so it rests on the enclosing strip 9, as his Fig. 4.

Matériaux pour cette étape :

Carton contrecolléCarton contrecollé1 pièce
Papier cartonnéPapier cartonné1 pièce
ColleColle1 pièce

Outils nécessaires :

RègleRègle
Cutter de précisionCutter de précision
Plioir en osPlioir en os
Pinceau à collePinceau à colle
7

Fill and close it

Put the sweets in the lower tray, set the upper tray on it, lay the valentine in and bend the wings down over it, and put the lid on. Lift the upper tray off to reach the sweets.
8

Troubleshooting

Valentine box troubleshooting.

Flow

Loading...
9

History and honest limits

**Harry Richter** of Omaha, US 901,476, dated 20 October 1908, filed 29 November 1907. He claimed a box with a lower receptacle with an inner sustaining rim, an upper receptacle with an outer enclosing rim, "flexible holding-wings having flanges secured upon the inner sides of the integral upturned rim", and a cover. He made the wings "preferably of card board" and gives no sizes: the pasteboard, all sizes and glue are ours.

Matériaux

3

Outils requis

5

CC0 Domaine public

Ce blueprint est publié sous CC0. Vous êtes libre de copier, modifier, distribuer et utiliser ce travail pour tout usage, sans demander la permission.

Soutenez le Maker en achetant des produits via son Blueprint où il perçoit une Commission Maker définie par les Vendeurs, ou créez une nouvelle itération de ce Blueprint et incluez-le comme connexion dans votre propre Blueprint pour partager les revenus.

Commentaires

(0)

Se connecter pour participer à la discussion

Chargement des commentaires...