Collaboration
ART
BEAUTÉ ET BIEN-ÊTRE
ARTISANAT
CULTURE ET HISTOIRE
DIVERTISSEMENT
ENVIRONNEMENT
NOURRITURE ET BOISSONS
INGÉNIERIE INVERSE
SCIENCES
SPORTS
TECHNOLOGIE
TECHNOLOGIE PORTABLE
Easter Egg Dyeing Stand: a Crank-Turned Rubber Roller Spins the Egg Under the Brush (Young, 1943)
Woody

Créé par

Woody

13. novembre 2026NO
10
0
0
0
0

Easter Egg Dyeing Stand: a Crank-Turned Rubber Roller Spins the Egg Under the Brush (Young, 1943)

Raymond P. Young of Wrightsville, Pennsylvania, received US 2,327,754, dated 24 August 1943, for a little table for dyeing Easter eggs. The egg sits in an oval opening on a rubber roller turned by a crank; hold a dye brush against it and the colour goes on evenly all round. Grooves hold the brushes, a rack holds the dye bottles, and a rabbit stands at one end. We make it from plywood and dowel. All sizes are ours.
Débutant
About 4 hours

Consignes

1

Opening and roll

Chargement du notebook Jupyter…
2

Read US 2,327,754

"If a dye containing brush is held against the object 8, application of the dye to the object 8 will take place uniformly and in a convenient manner."
3

Cut the platform

Cut a platform of 12 mm plywood about 300 x 180 mm (ours). Near one corner cut an oval opening 70 x 40 mm with a coping saw, his opening 6. Glue a strip of thin plywood or a ring of dowel round it to make the rise 7, so the egg cannot roll off.

Matériaux pour cette étape :

Panneau de contreplaquéPanneau de contreplaqué1 pièce
Colle à boisColle à bois1 pièce

Outils nécessaires :

CrayonCrayon
Scie égoïneScie égoïne
Chignole à mainChignole à main
Scie à chantournerScie à chantourner
Papier abrasifPapier abrasif
4

Make the brush grooves

Glue short dowels across the top of the platform beside the opening, a little apart, so the gaps between them (his ribs 10 and grooves 11) hold the brushes.

Matériaux pour cette étape :

Goujons de bois durGoujons de bois dur1 pièce
Colle à boisColle à bois1 pièce

Outils nécessaires :

Scie égoïneScie égoïne
Papier abrasifPapier abrasif
5

Fit the legs

Drill the corners and glue in four dowel legs, his legs 9, long enough to clear the crank below (ours).

Matériaux pour cette étape :

Goujons de bois durGoujons de bois dur1 pièce
Colle à boisColle à bois1 pièce

Outils nécessaires :

Chignole à mainChignole à main
Scie égoïneScie égoïne
6

Make the roller

Slide rubber tubing over a steel rod for the roll 24 (his roll is rubber, "or any other suitable material"). Bend the rod's long end twice at right angles in the vice to make the crank handle 25.

Matériaux pour cette étape :

Tube en caoutchoucTube en caoutchouc1 pièce
Rond en acier douxRond en acier doux1 pièce

Outils nécessaires :

Étau d'établiÉtau d'établi
Scie à métauxScie à métaux
7

Hang the roller

Cut two bearing brackets from flat bar (ours, his bearings 21 and 22), drill each for the rod at the depth the notebook gives, bend them to hang below the platform and screw them on either side of the opening, so the roll sits under the opening as his Fig. 4. The egg should rest on the roll inside the rise and turn when the crank turns.

Matériaux pour cette étape :

Plat en acier douxPlat en acier doux1 pièce
Vis à boisVis à bois1 pièce

Outils nécessaires :

Scie à métauxScie à métaux
Perceuse à colonnePerceuse à colonne
Jeu de foretsJeu de forets
Étau d'établiÉtau d'établi
Jeu de tournevisJeu de tournevis
8

Make the bottle rack

Bend a strip of flat bar (his rack bar 14, "preferably strap iron") down and out at each end, drill a row of holes in it to hold the dye bottles, and screw its ends to the back edge of the platform.

Matériaux pour cette étape :

Plat en acier douxPlat en acier doux1 pièce
Vis à boisVis à bois1 pièce

Outils nécessaires :

Scie à métauxScie à métaux
Perceuse à colonnePerceuse à colonne
Jeu de foretsJeu de forets
Étau d'établiÉtau d'établi
Jeu de tournevisJeu de tournevis
9

Add the rabbit

Cut a rabbit from plywood with the coping saw, sand it and glue it upright at the far end, his figure 13.

Matériaux pour cette étape :

Panneau de contreplaquéPanneau de contreplaqué1 pièce
Colle à boisColle à bois1 pièce

Outils nécessaires :

Scie à chantournerScie à chantourner
Papier abrasifPapier abrasif
10

Dye an egg

Fill the bottles with food colouring (ours) and put them in the rack. Set a hard-boiled egg in the opening on the roll, turn the crank, and hold a dye-filled brush against the egg: the colour goes on in an even band. Move the brush across to stripe it.

Matériaux pour cette étape :

ŒufŒuf1 pièce
Colorant alimentaireColorant alimentaire1 pièce
Bouteilles en verre avec bouchonBouteilles en verre avec bouchon1 pièce

Outils nécessaires :

Jeu de pinceauxJeu de pinceaux
11

Troubleshooting

Egg dyeing stand troubleshooting.

Flow

Loading...
12

History and honest limits

**Raymond P. Young** of Wrightsville, Pennsylvania, US 2,327,754, dated 24 August 1943, filed 27 May 1942. He claimed "dyeing apparatus comprising a platform having an opening therein, a rotatable roller mounted at the underside of the platform and partly protruding into said opening, means for rotating the roller, and an upstanding article confining wall on the platform surrounding said opening". He gives no sizes or dye: the plywood, dowels, all sizes, the bracket bearings, the rubber tube on a rod, and food colouring are ours.

Matériaux

10

Outils requis

11

CC0 Domaine public

Ce blueprint est publié sous CC0. Vous êtes libre de copier, modifier, distribuer et utiliser ce travail pour tout usage, sans demander la permission.

Soutenez le Maker en achetant des produits via son Blueprint où il perçoit une Commission Maker définie par les Vendeurs, ou créez une nouvelle itération de ce Blueprint et incluez-le comme connexion dans votre propre Blueprint pour partager les revenus.

Commentaires

(0)

Se connecter pour participer à la discussion

Chargement des commentaires...