Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Arc Welder: AC Transformer with a Sliding Shunt Core (Fanger, US 2,248,070)
Forge

Dibuat oleh

Forge

9. November 2026NO
5
0
0
0
0

Arc Welder: AC Transformer with a Sliding Shunt Core (Fanger, US 2,248,070)

An AC arc welder is a step-down transformer whose current can be turned up and down. H. J. Fanger (US 2,248,070, 1941) cuts a gap through one leg of a laminated ring core and slides a laminated iron shunt bar through it: pushed in, it carries flux past the secondary and lowers the welding current; pulled out, the current rises. For arc welding he gives about 60 to 68 volts open circuit, 15 to 200 amps, dropping to 38 or 40 volts at the working arc, with a small coil on the shunt bar in series with the secondary. Source: H. J. Fanger, "Welding Transformer", US Patent 2,248,070 (filed 1938, granted 1941). Picture: its Figs. 1-5.
Lanjutan
Unknown

Instruksi

1

Read Fanger

"With arc welding, infinite control of the volume of the secondary current, between maximum and minimum is obtained by adjustment of the slidable shunt core without altering the welding characteristics of the current, also better ignition of the arc is had at a given voltage, and greater stability of the arc".
2

Stack the core

Build a single rectangular ring core of insulated iron laminations, held together with brass (or insulated) bolts or rivets in insulating tubes (Fig. 4). Cut a gap straight through one leg, accurately machined and finished, and make a circular joint through the opposite leg with the segments staggered to overlap in successive laminations. Core size, lamination iron and thickness are not given (ours: the tools).

Material untuk langkah ini:

Logam tidak diketahuiLogam tidak diketahui1 iron laminations
Aneka baut segi enamAneka baut segi enam1 brass bolts
Bahan isolasi tidak diketahuiBahan isolasi tidak diketahui1 insulating tubes

Alat yang dibutuhkan:

Gunting sengGunting seng
Mesin Bor DudukMesin Bor Duduk
Set Mata BorSet Mata Bor
Kikir (Kikir Tangan)Kikir (Kikir Tangan)
Dimensi tidak diketahuiDimensi tidak diketahui
3

Make the shunt bar

Make the sliding shunt section of the same laminated iron, a snug fit in the gap with its laminations edge-to-edge with the core's, and long enough to fill the gap at every position. Sheath both sides with a slightly wider plate of Bakelite that overlaps the edges of the gap to guide it. Fit a threaded rod on its outer end, working in a nut fixed to the section (or move it by hand, with calibration marks along one edge).

Material untuk langkah ini:

Logam tidak diketahuiLogam tidak diketahui1 shunt laminations
BakelitBakelit2 side plates
Aneka baut segi enamAneka baut segi enam1 brass bolts
Batang berulirBatang berulir1 buah
Mur Segi EnamMur Segi Enam1 buah

Alat yang dibutuhkan:

Mesin Bor DudukMesin Bor Duduk
Set Mata BorSet Mata Bor
Kikir (Kikir Tangan)Kikir (Kikir Tangan)
4

Wind the coils

Wind the primary and secondary windings on both legs of the core (Fig. 2), in series or in parallel to suit the line voltage and the current wanted. Wind a small auxiliary coil round the shunt bar's path, fixed so the bar slides through it, and connect it in series with the secondary through a reversing switch (some jobs weld better with the current through it one way). Turns and wire sizes are not given.

Material untuk langkah ini:

Kawat TembagaKawat Tembaga1 insulation and size not given

Alat yang dibutuhkan:

Dimensi tidak diketahuiDimensi tidak diketahui
5

Spring the joints

On both sides of the gap and of the circular joint fit pairs of confronting angle plates, held by brass bolts in insulating sleeves and drawn together by spring bolts whose heads rest on slightly arched spring plates, so the joints close snugly on the sliding bar. A small lever on the gap-joint nut gives a half turn to release the bar for moving. The angle-plate material is not given.

Material untuk langkah ini:

Bahan tidak diketahuiBahan tidak diketahui4 angle plates
Aneka baut segi enamAneka baut segi enam1 brass and spring bolts
Bahan isolasi tidak diketahuiBahan isolasi tidak diketahui1 sleeves
Pita baja pegasPita baja pegas1 arched spring plates
Mur Segi EnamMur Segi Enam4 buah

Alat yang dibutuhkan:

Mesin Bor DudukMesin Bor Duduk
Set Mata BorSet Mata Bor
Kunci InggrisKunci Inggris
6

Connect and set

Connect the primary to the line through a line switch, and the secondary leads to the electrode holder and the work. Pull the shunt bar out for more current, push it in for less: Fanger gives about 60-68 volts open circuit and 15-200 amps, dropping to 38-40 volts at the arc.

Material untuk langkah ini:

Sakelar hidup/matiSakelar hidup/mati1 line switch

Alat yang dibutuhkan:

Kunci InggrisKunci Inggris

Bahan

10

Alat yang Diperlukan

6

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...