SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Battery Holder: Four C Cells in Two Sprung Compartments with a Z-Shaped Retainer (Lund 1979)
Ed

Dibuat oleh

Ed

28. Oktober 2026FI
1
0
0
0
0

Battery Holder: Four C Cells in Two Sprung Compartments with a Z-Shaped Retainer (Lund 1979)

A tray for four C cells in series, made for an instrument that gets knocked about. Each compartment holds two cells end to end, pressed together by a cone-shaped coil spring. The cells can shift a little under a blow and spring back without losing contact. A small Z-shaped retainer holds down one cell in each row and still lets every cell be taken out. Source: John Lund, US 4,161,568 (Schonstedt Instrument Co., 1979), with all sizes. Unknown: the plastic, the metals and the spring wire size. Lund names none of them, and nothing makes a self-tapping screw yet, so these are linked to unknown heads. The tools are ours. Picture: the patent's Fig. 1.
Menengah
1 day

Instruksi

1

Mould the tray

Mould a tray 4.325 × 2.500 × 0.875 in (109.9 × 63.5 × 22.2 mm) with two parallel open-top compartments, each 4.125 in long, 1.025 in wide and 0.800 in deep inside (104.8 × 26.0 × 20.3 mm). The middle wall is 0.300 in (7.6 mm) thick, with a notch at one end. Mould two small abutments on the middle wall, 1.000 in (25.4 mm) apart. Unknown: the plastic.

Material untuk langkah ini:

Bahan isolasi tidak diketahuiBahan isolasi tidak diketahui1 as required

Alat yang dibutuhkan:

Cetakan kompresiCetakan kompresi
Jangka Sorong VernierJangka Sorong Vernier
2

Wind the two spring contacts

Wind two cone-shaped coil springs: 0.562 in (14.3 mm) outside diameter at the large end, 0.312 in (7.9 mm) inside at the small end, 1/2 in (12.7 mm) long free, closing to 1/8 in (3.2 mm). Each has three active turns, and the end turns are wound flat. Leave one spring with a long straight tail. Unknown: the metal and the wire size.

Material untuk langkah ini:

Logam tidak diketahuiLogam tidak diketahui1 as required

Alat yang dibutuhkan:

Tang berujung bulatTang berujung bulat
Tang Berujung RataTang Berujung Rata
Jangka Sorong VernierJangka Sorong Vernier
3

Fit the contacts and terminals

Put one spring at the far end of the first compartment, with its straight tail, and the other at the near end of the second. Set an eyelet contact in the end wall opposite each spring. Run the tail through the notch in the middle wall to the eyelet contact at the far end of the second compartment. Fix two terminals to the near end wall with eyelets, each holding its contact.

Material untuk langkah ini:

Logam tidak diketahuiLogam tidak diketahui1 as required

Alat yang dibutuhkan:

Gunting sengGunting seng
Tang Berujung RataTang Berujung Rata
Kikir tanganKikir tangan
4

Make and fix the retainer

Cut a flat Z-shaped retainer of plastic, 0.062 in (1.6 mm) thick and 0.980 in (24.9 mm) long. It is 0.430 in (10.9 mm) wide at each branched end. Each branch sticks out 0.130 in (3.3 mm) from the stem and runs 0.365 in (9.3 mm) along it. Screw it with a single self-tapping screw through the middle of the stem onto the top of the middle wall, between the abutments, so it cannot turn. Each branch reaches over one compartment.

Material untuk langkah ini:

Bahan isolasi tidak diketahuiBahan isolasi tidak diketahui1 as required
Sekrup tappingSekrup tapping1 pc

Alat yang dibutuhkan:

Gunting sengGunting seng
Kikir tanganKikir tangan
Set obengSet obeng
Jangka Sorong VernierJangka Sorong Vernier
5

Wire it

Solder lead wires to the two terminals. With the cells in, the four make one series supply between these terminals.

Material untuk langkah ini:

Kabel penghubungKabel penghubung1 as required
Kawat Timah SolderKawat Timah Solder1 as required

Alat yang dibutuhkan:

SolderSolder
6

Load the cells

Put cell 1 into the free end of the first compartment, slide it along under the retainer until it meets the spring, then drop cell 2 in behind it, pressing the spring a little. Load the second compartment from its other end the same way. To unload, lift out the two free cells, then slide the held cells along into their places and lift them out. Ours: check the voltage across the terminals with a meter.

Alat yang dibutuhkan:

MultimeterMultimeter

Bahan

5

Alat yang Diperlukan

9

Cetak biru ini membuat

Thumbnail
Placeholder

Dudukan baterai

Free

264
0

Blueprint terkait

Blueprint ini berbagi pengetahuan — teknik, bahan, atau prinsip

Push Button: Normally Open Momentary Switch with a Cushioned Contact (De Reamer, GE 1939)

Push Button: Normally Open Momentary Switch with a Cushioned Contact (De Reamer, GE 1939)

oleh EdFI

Elektronik

1
0
0
0
0
0
Extension Spring Wound by Hand with Hooked Ends

Extension Spring Wound by Hand with Hooked Ends

oleh ForgeNO

Pengerjaan Logam

16
0
0
0
0
0

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...