Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Bench Glassblowing Torch: Brass Gas Blowpipe with a Glass Air Jet (Shenstone, 1916)
Penny

Dibuat oleh

Penny

3. November 2026DK
15
0
0
1
0

Bench Glassblowing Torch: Brass Gas Blowpipe with a Glass Air Jet (Shenstone, 1916)

A glassblower's gas blowpipe you can make yourself: a brass tube with a side tube for gas, and a glass air jet down its middle fed from a foot-blower. A fine jet gives the small pointed flame for joints, and a wider jet the big brush flame for heating large tubes. It is pegged into a wooden block on a sheet-iron-covered bench, with taps for gas and air at the bench edge. Result: a bench blowpipe for working glass tube. Make two: one about 11 mm bore for small work, one 15 to 17 mm for large. Source: W. A. Shenstone, The Methods of Glass-Blowing (1916), pp. 3-9. Unknown: the brazing metal and the tap type. Picture: Fig. 1 of the book.
Menengah
Unknown

Instruksi

1

Braze the gas inlet

Take a brass tube for the body: about 11 mm bore for the small blowpipe, 15 to 17 mm for the large one. Braze a side tube for the gas onto it 10 to 12 cm from the back end, according to the tube's size. Fix a spike to it for mounting. Ours: borax as the flux. Not given: the brazing metal.

Material untuk langkah ini:

Tabung kuninganTabung kuningan1 body and side tube
Logam tidak diketahuiLogam tidak diketahui1 brazing metal and spike
Serbuk boraksSerbuk boraks1 brazing flux

Alat yang dibutuhkan:

Gergaji BesiGergaji Besi
Tungku TempaTungku Tempa
2

Fit the glass air jet

Fit a glass tube down the middle of the brass tube, held by a cork at the back end, its tip near the mouth. For the small pointed flame, draw the tip down to the size of a large knitting needle. For a large flame rich in air, the tip may be nearly half the bore of the brass tube. Make several air tubes of different sizes for each blowpipe.

Material untuk langkah ini:

Tabung kacaTabung kaca3 air jets of several sizes
Sumbat gabusSumbat gabus1 jet cork

Alat yang dibutuhkan:

Pembakar BunsenPembakar Bunsen
3

Set up the bench

Cover the bench round the blowpipe with sheet iron. Drill several holes in a block of wood so the spike can be set at different positions. Fix two taps near the bench edge, one for gas and one for air. Connect them by flexible tubes to the supplies on one side and to the blowpipe's gas inlet and air jet on the other. Ours: mild steel sheet, rubber tubing. Not given: the tap type.

Material untuk langkah ini:

Pelat Baja LunakPelat Baja Lunak1 bench cover
Balok Kayu KerasBalok Kayu Keras1 mounting block
Katup tak diketahuiKatup tak diketahui2 gas and air taps
Selang KaretSelang Karet1 flexible tubes

Alat yang dibutuhkan:

Mesin Bor DudukMesin Bor Duduk
4

Light it and blow

Light the gas at the mouth and work a foot-blower to drive air through the glass jet into the burning gas. Little air and a small jet give the pointed flame; plenty of gas and a strong blast give the large, non-luminous brush flame.

Alat yang dibutuhkan:

Ubub (Pengembus)Ubub (Pengembus)

Bahan

9
  • 1 body and side tube
    Placeholder
  • 1 brazing metal and spike
    Placeholder
  • 1 brazing flux
    Placeholder
  • 3 air jets of several sizes
    Placeholder
  • 1 jet cork
    Placeholder
  • 1 bench cover
    Placeholder
  • 1 mounting block
    Placeholder
  • 2 gas and air taps
    Placeholder
  • 1 flexible tubes
    Placeholder

Alat yang Diperlukan

5

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...