Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Blake Jaw Breaker: Eccentric, Pitman and Two Toggles Swing a Steel Jaw Against a Fixed Chilled Plate (Richards, Ore Dressing, 1903)
Forge

Dibuat oleh

Forge

15. November 2026NO
6
0
0
0
0

Blake Jaw Breaker: Eccentric, Pitman and Two Toggles Swing a Steel Jaw Against a Fixed Chilled Plate (Richards, Ore Dressing, 1903)

Eli Whitney Blake's jaw breaker (patented 1858), the standard first crusher of the ore mill, as Robert Richards described it: a ribbed cast frame on four legs, a fixed jaw bedded in zinc, a steel swing jaw hung from a shaft at the top, and an eccentric that lifts a pitman to straighten two toggles and push the jaw shut; rubber springs pull it back. A wedge sets the gap; a heavy flywheel carries it through each half-turn of crushing.
Lanjutan
Weeks (castings and machining)

Instruksi

1

Sizes and power

Memuat notebook Jupyter…
2

Read Richards

"As the eccentric lifts the pitman, it straightens out the toggles, lengthening the distance between their outer ends. This forces the swing jaw to approach the fixed jaw, crushing the rock."
3

Frame and fixed jaw

Cast the frame of strong, ribbed cast iron or cast steel, with four legs bolted down, bearing boxes on top for the swing-jaw shaft and the eccentric shaft, and a horizontal web at the rear for the toggle block and wedge. Bed the fixed jaw against the frame end with 1/4 in. (6 mm) of zinc, and hold its jaw plate with two wedge-shaped cheek plates driven into recesses in the frame.

Material untuk langkah ini:

Benda cor besiBenda cor besi1 buah
Batangan SengBatangan Seng1 buah
Aneka baut segi enamAneka baut segi enam1 buah

Alat yang dibutuhkan:

Gayung tuang logamGayung tuang logam
TakalTakal
PaluPalu
4

Swing jaw

Make the swing jaw of steel, fixed to its shaft by a gib and key bolt, with its jaw plate held by dovetails, a steel toggle bearing at the back and an eye near the bottom for the spring rod. Jaw plates: chilled cast iron with lengthwise 90° corrugations.

Material untuk langkah ini:

Benda cor besiBenda cor besi1 buah
Poros bajaPoros baja1 buah

Alat yang dibutuhkan:

Mesin Bubut LogamMesin Bubut Logam
Set kunci pasSet kunci pas
5

Pitman, toggles and wedge

Hang a strong steel pitman from the eccentric shaft on babbitt bearings taken up by a key. Fit two toggles: one between the toggle block and the pitman, one between the pitman and the swing jaw, all four toggle bearings steel, held by set screws. Set the toggle block on its bolt against the wedge, which an adjusting bolt raises or lowers.

Material untuk langkah ini:

Poros bajaPoros baja1 buah
Logam tidak diketahuiLogam tidak diketahui1 buah
Benda cor besiBenda cor besi1 buah

Alat yang dibutuhkan:

Mesin Bubut LogamMesin Bubut Logam
Set kunci pasSet kunci pas
6

Springs, flywheel and drive

Fit two spring rods from the swing jaw through rubber springs held in compression against a spring bar. Key a heavy flywheel to the eccentric shaft and bolt the drive pulley to it; plug all oil holes against grit and shield the boxes and toggles with the half hopper. Drive it by belt (Table 5: 275 rev./min).

Material untuk langkah ini:

Lembaran karet alamLembaran karet alam1 buah
Benda cor besiBenda cor besi1 buah
KatrolKatrol1 buah
Sabuk penggerakSabuk penggerak1 buah
Aneka baut segi enamAneka baut segi enam1 buah

Alat yang dibutuhkan:

Set kunci pasSet kunci pas
Mesin Bubut LogamMesin Bubut Logam
7

Run and adjust

Feed rock by hand, shovel or chute into the mouth. As the jaw plates wear and the product gets coarse, raise the wedge by its nut; when that is used up, fit longer toggles that keep the pitman vertical; then turn the jaw plates end for end; last, fit new plates.

Alat yang dibutuhkan:

Set kunci pasSet kunci pas
8

Troubleshooting

Jaw breaker troubleshooting.

Flow

Loading...
9

History and honest limits

From Robert H. Richards, *Ore Dressing* vol. I (1903), Chapter II, §§ 11-14, pp. 13-17, Figs. 5-8 and Table 5 (checked on the archive.org scan oredressing01richuoft; p. 15 from its text layer). Blake's first 1858 form gave the most movement at the mouth; he soon reversed it so the bottom of the jaw moves most. Richards describes a bought Farrel or Fraser & Chalmers machine: building it from castings and metric figures are ours, and the babbitt alloy has no head yet.

Bahan

8

Alat yang Diperlukan

5

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...