Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Stamp Mill: California Five-Stamp Battery (Richards, Ore Dressing 1903)
Forge

Dibuat oleh

Forge

3. November 2026NO
15
0
0
0
0

Stamp Mill: California Five-Stamp Battery (Richards, Ore Dressing 1903)

The gravity stamp mill: five heavy iron stamps stand in a cast-iron mortar on a timber block. Cams on a turning shaft lift each stamp by its tappet and let it fall by its own weight onto the ore on a die. Water washes the crushed ore out through a screen. Result: a stamp battery that pounds ore to sand, at 80 to 110 drops a minute. Source: R. H. Richards, Ore Dressing, vol. I (1903), Chapter V, Gravity Stamps. Unknown: one complete set of sizes; Richards gives the range found in the mills. Picture: Fig. 90 of the book.
Lanjutan
Unknown

Instruksi

1

Dig and level the foundation

Dig a trench in gravel, or blast one in rock, about 2 feet longer than the mortar block at each end and about 2 feet wider at each side. Level the bottom with tamped concrete, sand or clay. Concrete should be at least 30 inches thick, or it may crumble. Two layers of 2-inch plank spiked together may go on top.

Material untuk langkah ini:

BetonBeton1 levelling layer
Papan kayuPapan kayu1 two layers of 2-inch plank

Alat yang dibutuhkan:

SekopSekop
PaluPalu
2

Stand the mortar block

Stand timbers or planks on end in the trench as the mortar block, sized for one five-stamp mortar. The mills used everything from 30 x 30 inch squared timbers to 2 x 12 inch planks bolted together. Set vertical bolts 3 to 4 feet long into the block to hold the mortar down. Not given: the bolts' metal.

Material untuk langkah ini:

Kayu balok persegiKayu balok persegi1 mortar block
Logam tidak diketahuiLogam tidak diketahui1 hold-down bolts

Alat yang dibutuhkan:

Set kunci pasSet kunci pas
Dimensi tidak diketahuiDimensi tidak diketahui
3

Build the frame

On mud sills and cross sills, stand the posts (end posts 12 x 24 inches in most mills) with buckstaves, a platform, and lower and upper guide timbers. The guides keep the stamp stems vertical. Fit finger bars on a jack shaft between the posts, so each stamp can be propped up under its tappet. The frame carries the cam shaft and the drive.

Material untuk langkah ini:

Kayu balok persegiKayu balok persegi1 sills, posts, guide timbers, platform
Logam tidak diketahuiLogam tidak diketahui1 bolts and jack shaft

Alat yang dibutuhkan:

Set kunci pasSet kunci pas
Dimensi tidak diketahuiDimensi tidak diketahui
4

Set the mortar, dies and screen

Bed the cast-iron mortar on tarred blankets or sheet rubber on the mortar block, for an even bearing, and bolt it down. Put the dies in its bottom: cylinders on square foot plates that fill the floor of the mortar. Mount a screen of punched Russia sheet iron in a wooden frame over the opening in front.

Material untuk langkah ini:

Benda cor besiBenda cor besi1 mortar and five dies
Lembaran karet alamLembaran karet alam1 packing
Lembaran besi RusiaLembaran besi Rusia1 screen

Alat yang dibutuhkan:

Set kunci pasSet kunci pas
5

Make the five stamps

Each stamp has four parts. The shoe is chilled cast iron, its butt cast in heavy chills and its shank in sand. The boss is tough cast iron, the shoe's diameter and often 18 inches long, with sockets for the shoe shank and the stem and two keyways for knock-out wedges. The stem is solid wrought iron or mild steel, turned true and tapered at both ends so it can be reversed. The tappet is cast iron, with a flange above and below, locked on the stem by a gib and keys. Put the extra weight in the boss. Louis designs for 11 to 14 pounds of stamp per square inch of die; the mills used stamps of 650 to 1,100 pounds.

Material untuk langkah ini:

Benda cor besiBenda cor besi1 shoes, bosses, tappets
Batang besi tempaBatang besi tempa1 stems, gibs, keys

Alat yang dibutuhkan:

Mesin Bubut LogamMesin Bubut Logam
Dimensi tidak diketahuiDimensi tidak diketahui
6

Fit the cam shaft and drive

Turn a wrought-iron or steel cam shaft true, with a key seat, and key on five cams. Each cam usually has two arms with spiral lifting faces, cast iron with chilled faces or cast steel. Drive the shaft by a rubber belt from the main shaft, over a pulley of wood built on a cast-iron hub and flanges, with a tightener. Not given: the engine or wheel that turns the main shaft.

Material untuk langkah ini:

Batang besi tempaBatang besi tempa1 cam shaft
Benda cor besiBenda cor besi1 cams, pulley hub and flanges
Papan kayuPapan kayu1 pulley rim
Sabuk penggerakSabuk penggerak1 rubber belt

Alat yang dibutuhkan:

Mesin Bubut LogamMesin Bubut Logam
Set kunci pasSet kunci pas
7

Add the water and the feed

Run one or two 1-inch water pipes into the back of the mortar, each with a plug cock that stays where it is set. Feed ore from the bin by a chute to an automatic feeder. One stamp trips the feeder when the ore layer on its die gets too thin, and a hand screw adjusts the point where it trips. Ore can also be fed by hand with a shovel.

Material untuk langkah ini:

Pipa airPipa air1 water pipes
Katup tak diketahuiKatup tak diketahui1 plug cocks
Logam tidak diketahuiLogam tidak diketahui1 feeder and chute

Alat yang dibutuhkan:

Set kunci pasSet kunci pas
SekopSekop
8

Set up each stamp

Lay a 3-inch plank on the dies and set the bosses on it. Lower the stems into them and tap each stem down with a hammer, a board guarding its top, then drop it a few times at a very low drop. Hoist the stamp, put the shoe in place with wooden staves around its shank, and drop it on the plank to drive the shoe home; the staves swell when wet and hold it. Swap the plank for a block as high as the drop. Slip the tappet on, turn the cam until the tappet rests on its point, drive the keys home and drop the stamp gently a few times.

Material untuk langkah ini:

Baji kayuBaji kayu1 staves

Alat yang dibutuhkan:

Papan kayuPapan kayu
PaluPalu
TakalTakal
9

Run the battery

Drop the stamps in order 1, 3, 5, 2, 4 (numbered from the left, standing behind the battery), so no two neighbours fall one after the other. The California practice is 80 to 110 drops a minute with a 5 to 9 inch drop. The cams turn the stamps as they lift, which evens out wear on shoes and dies. Lubricate the cams; soft soap with graphite is best. As shoes and dies wear, reset the tappets to restore the drop, and keep the height of discharge, from die to screen, the same.

Alat yang dibutuhkan:

Bubuk GrafitBubuk Grafit
Bahan tidak diketahuiBahan tidak diketahui
Set kunci pasSet kunci pas

Bahan

12

Alat yang Diperlukan

10

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...