Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI

Coasting Toboggan: Four Steamed Hardwood Boards Bent Over a Log Form (Boy Mechanic, 1919)
A. M. Parker's toboggan from The Boy Mechanic, Book 3 (1919), 7-1/2 ft long and 16 in wide: four 5/16 in hardwood boards steamed at one end and bent round a 12 in log on a simple form, held by notched cross cleats, the curl riveted and wired, and a rope run along the sides.
Menengah
About 1 week (four days drying)
Instruksi
1
1
His mill bill in centimetres
His mill bill in centimetres
Memuat notebook Jupyter…
2
2
Read The Boy Mechanic, Book 3
Read The Boy Mechanic, Book 3
"Essentials of a good toboggan, whether for coasting or use in transportation, are strength and lightness." Woods in order of merit: hickory, birch and oak (not quarter-sawed).
3
3
Prepare the boards and cleats
Prepare the boards and cleats
Choose four 5/16 by 4 in by 10 ft boards straight in grain and free from knots. Plane the running side and bevel the edges so that, together, they form a wide V joint half the depth of the boards. Notch the seven 1 by 1 in cross cleats on one side, 1 in from each end, for the side ropes.
Material untuk langkah ini:
Papan Kayu Keras4 buahAlat yang dibutuhkan:
Ketam tangan
Gergaji Tangan
Pahat kayu
Pensil
Meteran Gulung4
4
Build the bending form
Build the bending form
Bore a gimlet hole through the centre of each 1 by 2 by 18 in piece and two more 4-1/4 in each side of it. Nail one 6 ft common board to each end of the 12 in by 18 in log block so their ends run parallel. With 3 in nails fix one bored cleat to the block between them, held out 1/2 in by a temporary spacer.
Material untuk langkah ini:
Papan pinus2 buah
Paku1 buahAlat yang dibutuhkan:
Gergaji Tangan
Bor tangan
Palu5
5
Steam and bend
Steam and bend
Steam about 3 ft of the board ends, or boil them in a tank. Clamp or nail the dry ends together edge to edge between two of the 1 by 2 in pieces, about 1/4 in apart. Push the steamed ends under the cleat on the block (its nails slip between the boards), bear down and nail on another bored cleat as far as the floor allows. Turn it over and bend the boards round the block, nailing on more cleats, until the clamped end lies between the 6 ft boards; hold it with a piece nailed across. The closer the cleats, the less risk of splitting.
Material untuk langkah ini:
Paku1 buahAlat yang dibutuhkan:
Panci Besar
Palu
Klem batang6
6
Fit the cleats and finish
Fit the cleats and finish
Dry at least four days on the form. Clamp the two 1/2 by 1 in pieces on each side of the bow ends, drill through and rivet them. Rivet a 1 by 1 in crossbar inside the bow at the extreme front and another under the end of the curl, and wire them together to hold the bend. Put the tail crossbar not nearer than 2-1/2 in from the board ends and space the rest evenly, notched side down. Trim, scrape and sandpaper the bottom, finish with oil, and run a 3/8 in rope through the notches under the cleat ends.
Material untuk langkah ini:
Papan Kayu Keras1 buah
Paku keling baja1 buah
Kawat besi1 buah
Minyak Biji Rami1 buah
Amplas1 buah
Tambang kapas1 buahAlat yang dibutuhkan:
Bor tangan
Palu
Gergaji Tangan
Kerok baja
Tang Berujung Rata7
7
Troubleshooting
Troubleshooting
Toboggan troubleshooting.
Flow
Loading...
8
8
History and honest limits
History and honest limits
From "Making a Coasting Toboggan" by A. M. Parker, in **The Boy Mechanic, Book 3**, Popular Mechanics, 1919 (Project Gutenberg 71856; checked on the archive.org scan boymechanic0003unse, pp. 11-13). The tools and metric figures are ours.
Bahan
8- 4 buahPlaceholder
- 2 buahPlaceholder
- 2 buahPlaceholder
- 1 buahPlaceholder
- 1 buahPlaceholder
- 1 buahPlaceholder
- 1 buahPlaceholder
- 1 buahPlaceholder
Alat yang Diperlukan
11- Placeholder
- Placeholder
- Placeholder
- 1 vendor sell this, none ship to you yetPlaceholder
- 1 vendor sell this, none ship to you yetPlaceholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
Cetak biru ini membuat
Blueprint terkait
Blueprint ini berbagi pengetahuan — teknik, bahan, atau prinsip
CC0 Domain Publik
Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.
Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.


