Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Distillation Column Assembly: Flask, "Evaporator" Still-Head, Liebig Condenser and Receivers (Young, 1903)
Charlie

Dibuat oleh

Charlie

3. November 2026DE
10
0
0
0
0

Distillation Column Assembly: Flask, "Evaporator" Still-Head, Liebig Condenser and Receivers (Young, 1903)

A complete fractional distillation set: a globular flask, Young and Thomas's 'evaporator' still-head built of stacked glass sections, a Liebig condenser and a row of receivers. In each section the rising vapour is forced through the liquid running back down, so the mixture separates better at each step. Result: a fractionating apparatus for separating liquids by boiling point, the fractions caught in receivers changed at set temperatures. Source: S. Young, Fractional Distillation (1903), pp. 4-7, 115-116, 166-168. Picture: Figs. 37 and 38 of the book.
Lanjutan
Unknown

Instruksi

1

Choose the still

Use a globular flask, since a flat-bottomed one may crack over a naked flame, no larger than the amount of liquid needs. Fit it with a cork for the still-head. Ours: a round-bottom flask.

Material untuk langkah ini:

Labu alas bulatLabu alas bulat1 still
Sumbat gabusSumbat gabus1 still cork

Alat yang dibutuhkan:

Pembakar BunsenPembakar Bunsen
2

Blow the evaporator still-head

Build the still-head of sections joined end to end. Each outer tube is 22 to 24 mm inside and about 10 to 10.5 cm long, constricted at the bottom. In it stands a thin inner tube, 7.5 to 8 mm inside and 60 mm long, open at both ends, with two large holes near its top. Its lower end widens into a funnel resting on the constriction, with three or four tiny glass beads fused to the rim so it does not fit too tightly. Over it stands an intermediate tube about 14 mm inside and 50 mm long, like a small inverted test tube. A small funnel, slightly wider than the dip in the outer tube above, sits on top of it on three glass legs. Small glass projections centre the tubes. Make the head long enough that the thermometer's bulb and stem both sit in the vapour, with a side delivery tube at the top.

Material untuk langkah ini:

Tabung kacaTabung kaca1 sections, inner and intermediate tubes, delivery tube

Alat yang dibutuhkan:

Obor peniup kaca mejaObor peniup kaca meja
3

Fit the condenser

Use a Liebig condenser, about 7 or 8 mm inside for the inner tube and 15 mm for the outer, cooled by running water. Pass the delivery tube through a cork into it. Draw out the joint where the wide inlet meets the narrow tube so no pool of liquid lies there. Bend the narrow tube so the condenser can stand upright. Above about 170 °C use a long tube cooled by air instead of water.

Material untuk langkah ini:

Kondensor berpendingin airKondensor berpendingin air1 condenser
Sumbat gabusSumbat gabus1 condenser cork

Alat yang dibutuhkan:

Obor peniup kaca mejaObor peniup kaca meja
AirAir
4

Set the heat and the receivers

Heat with a Bunsen burner, its top about 2 mm below the flask so the small flame touches the glass, shielded from draughts. Add a few pieces of porous porcelain (a broken clay pipe will do) or pumice if the liquid bumps. Set a thermometer in the still-head and a row of small flasks as receivers.

Material untuk langkah ini:

TermometerTermometer1 still-head thermometer
Labu pengumpulLabu pengumpul10 receivers

Alat yang dibutuhkan:

Pembakar BunsenPembakar Bunsen
Bahan tidak diketahuiBahan tidak diketahui
5

Distil in fractions

Read the barometer and correct the set temperatures for it. Distil steadily. In each section, condensed liquid seals the narrow passage, so the vapour rises up the inner tube, down between the tubes and up again, while liquid drips from section to section back to the still. Collect the distillate in fractions, changing the receiver each time the temperature reaches one of the values fixed beforehand.

Alat yang dibutuhkan:

Barometer merkuriBarometer merkuri
Pembakar BunsenPembakar Bunsen
AirAir

Bahan

6
  • Placeholder
  • 1 condenser cork
    Placeholder
  • 1 sections, inner and intermediate tubes, delivery tube
    Placeholder
  • Placeholder
  • 1 still-head thermometer
    Placeholder
  • 10 receivers
    Placeholder

Alat yang Diperlukan

5

Blueprint terkait

Blueprint ini berbagi pengetahuan — teknik, bahan, atau prinsip

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...