Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Fuller, Pritchel and Hot Setts: Steel Welded into a Split Iron Bar, with Twisted Rod or Withy Handles (Edwinson, 1886)
Forge

Dibuat oleh

Forge

14. November 2026NO
6
0
0
0
0

Fuller, Pritchel and Hot Setts: Steel Welded into a Split Iron Bar, with Twisted Rod or Withy Handles (Edwinson, 1886)

The smith's own top and bottom tools, from George Edwinson's farrier's chapter in Amateur Work (1886): an inch iron bar upset, split into a fork and a steel wedge welded in, then forged into a fuller, pritchel punch, curved or straight hot sett, or a square-tanged bottom sett; the pritchel itself from 1/2 in. square tool steel; handles of twisted iron rod or green withy.
Lanjutan
A day at the forge for the set

Instruksi

1

His proportions

Memuat notebook Jupyter…
2

Read Edwinson

"To make this tool, heat and upset the end of an inch bar of iron; then heat again and split with a sett."
3

Split the iron

Heat and upset the end of a 1 in. (25 mm) iron bar. Heat again and split it with a hot set into a fork 1 to 1 1/4 in. long by 3/4 in. wide (his fig. 108).

Material untuk langkah ini:

Batang besi tempaBatang besi tempa1 buah

Alat yang dibutuhkan:

Perapian pandai besiPerapian pandai besi
Landasan TempaLandasan Tempa
GodamGodam
Pahat panasPahat panas
Tang pandai besiTang pandai besi
4

Weld in the steel

Heat the end of a steel bar of similar size and forge a wedge to fit the fork (fig. 109). Bring both to a welding heat and weld them well together.

Material untuk langkah ini:

Baja krusibelBaja krusibel1 buah
Serbuk boraksSerbuk boraks1 buah

Alat yang dibutuhkan:

Perapian pandai besiPerapian pandai besi
Landasan TempaLandasan Tempa
GodamGodam
Tang pandai besiTang pandai besi
5

Forge the fuller

Cut off 2 in. of steel and 3 in. of iron for the tool. Forge the steel, with the iron behind it, into the fuller's rounded blade (fig. 102). Make the neck while it is still on the bar, then cut it off leaving a piece of iron for the head.

Alat yang dibutuhkan:

Perapian pandai besiPerapian pandai besi
Landasan TempaLandasan Tempa
PaluPalu
Pahat panasPahat panas
6

Same blank, other tools

Pritchel punch: about 2 in. of iron and 1 in. of steel, shaped as fig. 103. Curved set: as the fuller but with a gouge-shaped blade (fig. 105). Top hot set: the same, with a chisel or wedge blade (fig. 106). Bottom set: a wedge of steel and iron, edge up, on a square tang that fits the anvil's square hole (fig. 107).

Material untuk langkah ini:

Batang besi tempaBatang besi tempa1 buah
Baja krusibelBaja krusibel1 buah
Serbuk boraksSerbuk boraks1 buah

Alat yang dibutuhkan:

Perapian pandai besiPerapian pandai besi
Landasan TempaLandasan Tempa
PaluPalu
GodamGodam
Tang pandai besiTang pandai besi
7

Forge the pritchel

Forge 1/2 in. (13 mm) square tool steel into the tapered pritchel (fig. 104), 6 in. (150 mm) long. It punches nail holes in hot iron, so it need not be hardened.

Material untuk langkah ini:

Batang baja perkakasBatang baja perkakas1 buah

Alat yang dibutuhkan:

Perapian pandai besiPerapian pandai besi
Landasan TempaLandasan Tempa
PaluPalu
Tang pandai besiTang pandai besi
8

Fit the handles

Rod handle: twist 3/8 in. iron rod once round the neck and weld the two ends together (fig. 110). Withy handle: take a green or half-green hazel, willow, oak or withy rod about 3 ft long, twist the middle 8-9 in., wrap it once round the neck and bind the two ends with wire or a link (figs. 106, 111).

Material untuk langkah ini:

Batang bulat baja lunakBatang bulat baja lunak1 buah
Ranting gandarusa (lentur)Ranting gandarusa (lentur)1 buah
Kawat besiKawat besi1 buah

Alat yang dibutuhkan:

Perapian pandai besiPerapian pandai besi
Landasan TempaLandasan Tempa
PaluPalu
Tang pandai besiTang pandai besi
9

Harden the cutting tools (ours)

He gives no temper for these. Ours: harden and temper the set edges as for other hot-cutting tools, and cool them often in use.

Alat yang dibutuhkan:

Perapian pandai besiPerapian pandai besi
Ember pendingin tempaEmber pendingin tempa
10

Troubleshooting

Top-tool troubleshooting.

Flow

Loading...
11

History and honest limits

From George Edwinson, "Smithing and Forging" VII, **Amateur Work, Illustrated**, vol. VI (1886-87), pp. 14-16 and figs. 101-111 (checked on the archive.org scan amateurworkillus06lond). He calls the top hot cutter a "sett"; we map it to the Hot Chisel head and the bottom sett to the Hot Cut Hardy head. Temper, metric figures and tools are ours.

Bahan

7

Alat yang Diperlukan

7

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...