Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Electromagnet: Horseshoe Holding Magnet Sized by Its Pull (Underhill, 1903)
Volt

Dibuat oleh

Volt

3. November 2026SE
10
0
0
0
0

Electromagnet: Horseshoe Holding Magnet Sized by Its Pull (Underhill, 1903)

A holding electromagnet in its practical horseshoe form: two iron cores, each wound with wire, fastened to an iron yoke, and an iron armature across the poles. You size it from the pull you need: the pull sets the pole area, and the supply voltage sets the wire. Variable: the pull. Each pound needs a set area of pole, depending on the iron. Source: C. R. Underhill, The Electromagnet (1903), pp. 92, 106-118, 150. Unknown: sizes and the ampere-turns. Picture: Fig. 51 of the book.
Menengah
Unknown

Instruksi

1

Size the poles from the pull

Pull P (pounds) = B² × A / 72,134,000, where B is the flux density in lines per square inch and A the pole area in square inches. Working densities: wrought iron 90,000, cast steel 85,000, Mitis iron 80,000, ordinary cast iron 50,000, which give 112.3, 100.1, 88.72 and 34.66 lb per square inch of pole. Divide the pull you need by that figure to get the pole area. Underhill's example, for cast steel taken at 90,000: 10 lb needs 0.089 square inch, a core 0.336 inch across. A two-pole magnet holds twice the weight of a single pole at the same induction.

Alat yang dibutuhkan:

Dimensi tidak diketahuiDimensi tidak diketahui
2

Make the cores, yoke and armature

Make the practical horseshoe magnet in three pieces besides the armature: two round cores and a yoke (back iron) to join them. Make an armature to lie across the two pole ends. Face the poles and the armature accurately; an uneven contact spreads the lines unevenly and weakens the pull. Ours: wrought iron. Not given: sizes, how the cores are fastened.

Material untuk langkah ini:

Batang besi tempaBatang besi tempa1 two cores, yoke, armature

Alat yang dibutuhkan:

Mesin Bubut LogamMesin Bubut Logam
Dimensi tidak diketahuiDimensi tidak diketahui
3

Choose the wire for the supply

Design the coil to stand the full supply voltage without overheating; never put a resistor in series with the magnet, as that wastes power and makes the magnet weaker. Pick the wire size that makes the coil's resistance equal to that of the line and the source, then try the next larger size, and keep the one giving more ampere-turns. A coil rises about 100 °F at about 0.9 watt per square inch of surface for a thin telephone-ringer coil, or 0.33 for a thick one (4 1/8 in across, 7 in long, 1 7/16 in thick), and the rise grows in proportion to the watts. Ours: the supply, e.g. 12 V.

Alat yang dibutuhkan:

Sumber daya arus searahSumber daya arus searah
Dimensi tidak diketahuiDimensi tidak diketahui
4

Wind the cores and fasten them to the yoke

Wind the wire directly onto each core between insulating end heads, and fasten the wound cores to the yoke. The joints between cores and yoke lose a little pull. Ours: enamelled copper wire. Not given: the winding method, the insulation.

Material untuk langkah ini:

Kawat Tembaga Berlapis EmailKawat Tembaga Berlapis Email1 two coils
Bahan isolasi tidak diketahuiBahan isolasi tidak diketahui1 end heads and core insulation
Logam tidak diketahuiLogam tidak diketahui1 core fastenings

Alat yang dibutuhkan:

Metode lilitan tak diketahuiMetode lilitan tak diketahui
Mesin Bubut LogamMesin Bubut Logam
5

Switch on and hold

Connect the coils to the supply and put the armature against the faced poles: the magnet holds it with the pull it was sized for. When the armature touches the poles there is practically no leakage between them.

Alat yang dibutuhkan:

Sumber daya arus searahSumber daya arus searah

Bahan

4

Alat yang Diperlukan

4

Cetak biru ini membuat

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...