Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
New Year Noisemaker: a Spun Box Whose Wooden Tongues Clack Over a Pinned Bobbin (Folkush, 1921)
Woody

Dibuat oleh

Woody

13. November 2026NO
8
0
0
0
0

New Year Noisemaker: a Spun Box Whose Wooden Tongues Clack Over a Pinned Bobbin (Folkush, 1921)

Martin Folkush of Milwaukee received US 1,374,644, dated 12 April 1921, for a noisemaker "that can be heard for a great distance". Hold the handle and swing the box round it: two thin wooden tongues inside snap over the posts of a fixed bobbin, one in single clacks and one in double, and the box rings like a sounding board. A slider changes the pitch. We make it from plywood, dowel and hardwood strip. All sizes are ours.
Menengah
About 4 hours

Instruksi

1

Posts on the bobbin

Memuat notebook Jupyter…
2

Read US 1,374,644

"Upon rotating the casing 12 upon the shaft 11, the sounding boards 21 and 22 will be brought into violent engagement with the posts 19 and 20 causing loud sounds to be emitted."
3

Make the handle and shaft

Shape a handle from hardwood handle stock with a rasp, his handle 10, and glue a dowel shaft 11 into its end.

Material untuk langkah ini:

Kayu Keras Bahan GagangKayu Keras Bahan Gagang1 buah
Pasak kayu kerasPasak kayu keras1 buah
Lem KayuLem Kayu1 buah

Alat yang dibutuhkan:

Gergaji TanganGergaji Tangan
Kikir kasar kayuKikir kasar kayu
AmplasAmplas
Bor tanganBor tangan
4

Make the bobbin

Cut three plywood disks 60 mm across (ours): two ends and the middle disk 18. Drill all three on the circle from the notebook and glue dowel posts 19 through all of them; then glue the shorter posts 20 between the middle disk and one end disk only, between the long ones. Drill the centre for the shaft and pin the bobbin to it, his pin 17.

Material untuk langkah ini:

Lembaran kayu lapisLembaran kayu lapis1 buah
Pasak kayu kerasPasak kayu keras1 buah
Lem KayuLem Kayu1 buah
PakuPaku1 buah

Alat yang dibutuhkan:

Gergaji CopingGergaji Coping
Jangka tusukJangka tusuk
Bor tanganBor tangan
Gergaji TanganGergaji Tangan
5

Make the casing

Cut two plywood sides 14 with a round head 13 at one end, bored for the shaft. Join them with a closed end 24 and an open frame so the bobbin turns freely between the heads. Glue a cross rib 23 inside the closed end. Cut a slot 28 in each side for the slider.

Material untuk langkah ini:

Lembaran kayu lapisLembaran kayu lapis1 buah
Lem KayuLem Kayu1 buah
PakuPaku1 buah

Alat yang dibutuhkan:

Gergaji TanganGergaji Tangan
Gergaji CopingGergaji Coping
Bor tanganBor tangan
6

Fit the sounding boards

Cut two thin hardwood strips (his sounding boards 21 and 22) long enough to reach from the rib to just inside the circle of posts, and screw their ends to the rib, side by side, one opposite each half of the bobbin.

Material untuk langkah ini:

Lis kayu kerasLis kayu keras1 buah
Sekrup kayuSekrup kayu1 buah

Alat yang dibutuhkan:

Gergaji TanganGergaji Tangan
Bor tanganBor tangan
Set obengSet obeng
7

Fit the slider and close the box

Make a small wooden slider 26 that surrounds both boards, with a length of threaded rod through it whose ends pass out through the slots; put a wing nut on each end (his set nuts 29). Put the casing on the shaft over the bobbin and close the other side with a plywood plate 25, making a resonant box.

Material untuk langkah ini:

Lis kayu kerasLis kayu keras1 buah
Batang berulirBatang berulir1 buah
Mur sayapMur sayap2 buah
Lembaran kayu lapisLembaran kayu lapis1 buah
Lem KayuLem Kayu1 buah

Alat yang dibutuhkan:

Gergaji TanganGergaji Tangan
Bor tanganBor tangan
Gergaji BesiGergaji Besi
8

Play it

Hold the handle and swing the box round the shaft: the boards snap over the posts. Slide the slider toward the bobbin for a higher, sharper sound, away for a deeper one, and lock it with the wing nuts.
9

Troubleshooting

Noisemaker troubleshooting.

Flow

Loading...
10

History and honest limits

**Martin Folkush** of Milwaukee, US 1,374,644, dated 12 April 1921, filed 10 April 1920. He claimed "a noise maker comprising a shaft, a casing journaled thereon, a frame having spaced end supported posts", "one half of said frame being provided with double the number of posts that the other half has", and the pitch-adjusting slider. He names no materials and gives no sizes: the wood, all sizes, wing nuts and threaded rod are ours.

Bahan

9

Alat yang Diperlukan

8

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...