Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Rotary Lawn Sprinkler: a Barker's-Mill Head Turning on Balls Round the Supply Pipe (Gibbs, 1901)
Forge

Dibuat oleh

Forge

13. November 2026NO
10
0
0
0
0

Rotary Lawn Sprinkler: a Barker's-Mill Head Turning on Balls Round the Supply Pipe (Gibbs, 1901)

Henry Gibbs of Chicago received US 683,645, dated 1 October 1901, for a lawn sprinkler "operating on the familiar Barker's mill principle": water leaving its arms sideways pushes the head round. His head turns on a ring of steel balls held in matching grooves in the head and in the end of the supply pipe, so it spins freely with little friction and stays on. We turn the head from brass and the groove in a steel pipe on the lathe. All sizes are ours.
Menengah
About 5 hours

Instruksi

1

How many balls

Memuat notebook Jupyter…
2

Read US 683,645

"It being only necessary that certain of the orifices shall discharge the water tangentially to revolve the head 14 and spray-pipes 15 in the well-known manner."
3

Groove the supply pipe

Chuck a length of steel pipe (his pipe 13) and finish its top end smooth and round. Cut a half-round groove (his 17) round it a little below the end, to the depth the notebook gives, with a round-nosed tool. Use thick-walled pipe, so at least 1.5 mm of wall is left under the groove (ours).

Material untuk langkah ini:

Pipa baja (berdinding tebal, ujung berulir)Pipa baja (berdinding tebal, ujung berulir)1 buah

Alat yang dibutuhkan:

Mesin Bubut LogamMesin Bubut Logam
Cekam bubut 3 rahangCekam bubut 3 rahang
Pahat bubutPahat bubut
Jangka Sorong Digital 6 InciJangka Sorong Digital 6 Inci
4

Turn the head

Turn a brass bar to a short round head (his 14). Bore it from below to loosely fit the pipe end, his bore 16, but stop short of the top so a lip (his flange 22) overhangs the pipe end. Cut a matching groove 18 inside the bore at the same height as the pipe's groove.

Material untuk langkah ini:

Batang Bulat KuninganBatang Bulat Kuningan1 buah

Alat yang dibutuhkan:

Mesin Bubut LogamMesin Bubut Logam
Cekam bubut 3 rahangCekam bubut 3 rahang
Pahat bubutPahat bubut
Set mata bor senterSet mata bor senter
Set Mata BorSet Mata Bor
Jangka Sorong Digital 6 InciJangka Sorong Digital 6 Inci
5

Drill the ball hole and the arms

Drill a hole (his opening 20) through the head's side into the groove, just bigger than a ball, and tap it for a screw plug (21). Drill three holes round the head into the bore for the spray pipes.

Alat yang dibutuhkan:

Mesin Bor DudukMesin Bor Duduk
Set Mata BorSet Mata Bor
Set pembuat ulirSet pembuat ulir
Ragum MejaRagum Meja
6

Make the spray pipes

Cut three lengths of copper tube, close their outer ends, and bend the last bit of each upward as his Fig. 1. Drill small holes near the ends, some pointing sideways (tangentially), all the same way round, so the jets turn the head. Solder the pipes into the head's holes (ours; he threads them in).

Material untuk langkah ini:

Pipa tembagaPipa tembaga1 buah
Patri timah-timbalPatri timah-timbal1 buah
FluksFluks1 buah

Alat yang dibutuhkan:

Gergaji BesiGergaji Besi
Set Mata BorSet Mata Bor
Mesin Bor DudukMesin Bor Duduk
Solder ListrikSolder Listrik
Ragum MejaRagum Meja
7

Assemble with the balls

Slide the head onto the pipe end with the grooves level. Feed balls in through the side hole, turning the head, until the race is full; then screw in the plug. The head should spin freely and not lift off.

Material untuk langkah ini:

Bantalan peluru baja (set)Bantalan peluru baja (set)1 buah
Sekrup mesinSekrup mesin1 buah

Alat yang dibutuhkan:

Kunci InggrisKunci Inggris
8

Make the stand

Bore a hardwood block to hold the pipe upright and glue in three splayed dowel legs (ours; his base 10 and supports 11). Screw the hose coupling onto the pipe's lower end below the block (his coupling 12).

Material untuk langkah ini:

Balok Kayu KerasBalok Kayu Keras1 buah
Pasak kayu kerasPasak kayu keras1 buah
Lem KayuLem Kayu1 buah
Kopling selangKopling selang1 buah

Alat yang dibutuhkan:

Gergaji TanganGergaji Tangan
Mesin Bor DudukMesin Bor Duduk
Set Mata BorSet Mata Bor
9

Run it

Connect a garden hose and turn on the water slowly: the jets push the head round and throw the water in a circle. More pressure turns it faster.
10

Troubleshooting

Lawn sprinkler troubleshooting.

Flow

Loading...
11

History and honest limits

**Henry Gibbs** of Chicago, assignor to W. D. Allen Manufacturing Company, US 683,645, dated 1 October 1901, filed 20 May 1901. He claimed a single-piece hollow coupling with radial spray pipes having tangential orifices, a bore loosely fitting the supply pipe, "annular grooves in the opposed cylindrical faces of said bore and said pipe" and "bearing balls interposed in said grooves". He gives no sizes or metals; the brass, steel pipe, ball size, soldered copper arms and the wooden stand are ours.

Bahan

11

Alat yang Diperlukan

13

Cetak biru ini membuat

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...