Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Foot-Fed Carriage Saw Table: The Saw Rides on Balls Under the Table, a Foot Lever Pulls It Through the Work (Hall, 1933)
Forge

Dibuat oleh

Forge

13. November 2026NO
7
0
0
0
0

Foot-Fed Carriage Saw Table: The Saw Rides on Balls Under the Table, a Foot Lever Pulls It Through the Work (Hall, 1933)

Harry O. Hall of Murray, Utah, received US 1,930,168, dated 10 October 1933, for a portable saw table where the saw moves and the work stays still. The saw and its motor hang from a carriage under the top. The carriage rolls on balls in V-shaped tracks in a straight line. A foot lever pulls it back through a board held against the fence, and springs bring it forward again. Nuts on a hanging stem set the depth, and a spring under the motor keeps the belts tight. The table rolls on wheels and its back legs fold. The patent gives no sizes; every size here is ours, and our top is plywood where his is folded sheet metal.
Lanjutan
About 1 week

Instruksi

1

The foot lever, the travel and the cut

Memuat notebook Jupyter…
2

Read US 1,930,168

"The movable saw carriage is mounted to freely move longitudinally of the table in a straight line and is moved into engagement with the piece of work held in position by the work fence, when the lever 29' is depressed by the foot."
3

Table and legs

Make the top 5 of 18 mm plywood 1000 x 600 mm with pine aprons 6, 7 round it, and cut a slot 47 12 mm wide and 500 mm long down its middle. Fix four pine legs 9, 10 splayed outwards at the corners with braces 11 and plywood gussets 12, the top 850 mm high; bolt the rear legs' gussets with one bolt each as a pivot and a second removable bolt, so they fold. Put an axle 15 between the front legs with a wheel 14 on each end.

Material untuk langkah ini:

Lembaran kayu lapisLembaran kayu lapis1 buah
Kayu pinusKayu pinus6 buah
Batang bulat baja lunakBatang bulat baja lunak1 buah
Set roda karetSet roda karet1 buah
Baut kepala bulat leher persegiBaut kepala bulat leher persegi8 buah
Sekrup kayuSekrup kayu40 buah
Lem KayuLem Kayu1 buah

Alat yang dibutuhkan:

Gergaji Ukir ListrikGergaji Ukir Listrik
Bor Tanpa KabelBor Tanpa Kabel
Set Mata BorSet Mata Bor
Klem batangKlem batang
Siku KombinasiSiku Kombinasi
Meteran GulungMeteran Gulung
4

Tracks and carriage

Screw a pine rail 22 along each side under the top and bolt a length of steel angle on it, V upwards, as the track 21. Make the carriage of two more angles 16, V downwards over the tracks, joined near each end by a cross bolt 17 with nuts 19 either side of each angle, so their spacing can be set. Under each end of each carriage angle, between the bolt and a small steel lug 23 bolted inside the angle, put a 10 mm steel ball 20 to roll in the track. Hook two springs 24 from the front wall of the top to the front cross bolt.

Material untuk langkah ini:

Kayu pinusKayu pinus1 buah
Besi siku baja lunakBesi siku baja lunak2 buah
Aneka baut segi enamAneka baut segi enam12 buah
Batang berulirBatang berulir1 buah
Mur Segi EnamMur Segi Enam8 buah
Besi Strip Baja LunakBesi Strip Baja Lunak1 buah
Bantalan peluruBantalan peluru1 buah
Pegas tarikPegas tarik2 buah
Sekrup kayuSekrup kayu16 buah

Alat yang dibutuhkan:

Gergaji BesiGergaji Besi
Gerinda sudutGerinda sudut
Mesin Bor DudukMesin Bor Duduk
Set Mata BorSet Mata Bor
Set KikirSet Kikir
Ragum MejaRagum Meja
Kunci InggrisKunci Inggris
Kacamata pengamanKacamata pengaman
5

Foot lever and chain

Pivot a hardwood foot lever 29' on the front axle, reaching back along the floor, with a pedal 31 on its free end. Fix a pulley 28 on a shaft 29 between the rear legs. Run a chain 27 from the rear cross bolt of the carriage over the pulley and down to the lever, fixed 450 mm from its pivot. Pressing the pedal pulls the carriage back; letting go, the springs return it.

Material untuk langkah ini:

Papan Kayu KerasPapan Kayu Keras1 buah
KatrolKatrol1 buah
Batang bulat baja lunakBatang bulat baja lunak1 buah
Rantai rolRantai rol1 buah
Aneka baut segi enamAneka baut segi enam3 buah

Alat yang dibutuhkan:

Gergaji Ukir ListrikGergaji Ukir Listrik
Bor Tanpa KabelBor Tanpa Kabel
Set Mata BorSet Mata Bor
Gergaji BesiGergaji Besi
Kunci InggrisKunci Inggris
6

Saw frame, arbor and shield

Bolt a rectangle of steel angle as the saw frame 32. Hang one end on the rear cross bolt between two collars 33 with set screws 34, so it can be slid sideways. On the front cross bolt put a sleeve 35 between collars 36 with a threaded stem 38 hanging from it, through a hole 39 in the frame's end, with a clamping nut 40 above and below: these set the saw's height. Bolt two flange bearings 42 across the frame and fit a 30 mm arbor 43 turned with a collar, a loose flange and an M20 thread; put the 250 mm blade on one end, centred under the slot, and a V-belt pulley 49 on the other. Bend a sheet steel shield 48 round the lower half of the blade and bolt it to the frame.

Material untuk langkah ini:

Besi siku baja lunakBesi siku baja lunak1 buah
Batang bulat baja lunakBatang bulat baja lunak2 buah
Baut tanam ujung cekungBaut tanam ujung cekung4 buah
Batang berulirBatang berulir1 buah
Mur Segi EnamMur Segi Enam4 buah
Bantalan flensBantalan flens2 buah
Circular Saw Blade SetCircular Saw Blade Set1 buah
Puli sabuk-V (penampang A)Puli sabuk-V (penampang A)1 buah
Pelat Baja LunakPelat Baja Lunak1 buah
Aneka baut segi enamAneka baut segi enam10 buah

Alat yang dibutuhkan:

Gergaji BesiGergaji Besi
Gerinda sudutGerinda sudut
Mesin Bor DudukMesin Bor Duduk
Set Mata BorSet Mata Bor
Set pembuat ulirSet pembuat ulir
Pemutar tap ulirPemutar tap ulir
Mesin Bubut LogamMesin Bubut Logam
Cekam bubut 3 rahangCekam bubut 3 rahang
Pahat bubutPahat bubut
Jangka Sorong Digital 6 InciJangka Sorong Digital 6 Inci
Gunting sengGunting seng
Ragum MejaRagum Meja
Kunci InggrisKunci Inggris
Set kunci LSet kunci L
7

Motor frame

Bolt a shorter angle frame 53 inside the saw frame, pivoted on the same rear cross bolt, and bolt the motor 51 under it with a V-belt pulley 50 in line with the arbor's. Hang its free end from a bolt 55 off a sleeve 56 on a rod 57 across the saw frame, with a spring 61 and washer 62 on the bolt above the motor frame and a nut 59 below. Fit the belt 52 and set its tension with the nut. Have the motor wired to a switch at the front.

Material untuk langkah ini:

Besi siku baja lunakBesi siku baja lunak1 buah
Motor listrikMotor listrik1 buah
Puli sabuk-V (penampang A)Puli sabuk-V (penampang A)1 buah
Sabuk V (penampang A)Sabuk V (penampang A)1 buah
Batang bulat baja lunakBatang bulat baja lunak1 buah
Batang berulirBatang berulir1 buah
Coil SpringCoil Spring1 buah
Ring RataRing Rata2 buah
Mur Segi EnamMur Segi Enam2 buah
Aneka baut segi enamAneka baut segi enam6 buah
Sakelar hidup/matiSakelar hidup/mati1 buah

Alat yang dibutuhkan:

Gergaji BesiGergaji Besi
Mesin Bor DudukMesin Bor Duduk
Set Mata BorSet Mata Bor
Kunci InggrisKunci Inggris
Set kunci LSet kunci L
8

Fence and first cut

Fix a hardwood fence 63 across the top near its rear end, standing past both sides, held by hook bolts 64 that hook under steel flanges 66 screwed to the gussets, with nuts 67. Set the blade 10 mm above the board's thickness with the stem's nuts. Hold a board against the fence, start the motor and press the pedal: the saw comes back through the board. Let the pedal up and it returns.

Material untuk langkah ini:

Papan Kayu KerasPapan Kayu Keras1 buah
Batang berulirBatang berulir1 buah
Mur Segi EnamMur Segi Enam2 buah
Besi Strip Baja LunakBesi Strip Baja Lunak1 buah
Sekrup kayuSekrup kayu8 buah

Alat yang dibutuhkan:

Gergaji Ukir ListrikGergaji Ukir Listrik
Bor Tanpa KabelBor Tanpa Kabel
Set Mata BorSet Mata Bor
Siku KombinasiSiku Kombinasi
Kacamata pengamanKacamata pengaman
Pelindung telinga (penutup telinga, SNR 30 dB)Pelindung telinga (penutup telinga, SNR 30 dB)
9

Troubleshooting

Carriage saw troubleshooting.

Flow

Loading...
10

History and honest limits

**Harry O. Hall** of Murray, Utah, US 1,930,168, dated 10 October 1933, filed 21 March 1933. He claimed a top with a longitudinal slot, "a traveling carriage mounted beneath said top and movable longitudinally thereof", a saw frame pivoted on one cross bar and hung from the other on a stem with nuts above and below, and a motor frame hung from the saw frame on a bolt with a spring. His top is folded sheet metal on splayed legs; ours is plywood on pine. His balls are confined between the cross bolts and lugs; ours the same, in steel angle. He gives no sizes; every size here is ours.

Bahan

27

Alat yang Diperlukan

22

Cetak biru ini membuat

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...