Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI

Instant-Read Thermometer: Digital, with a Stainless Probe That Pivots on the Case (Cook, US 5,018,875, 1991)
A pocket digital thermometer. A thin stainless steel probe with a thermistor in its tip pivots on a small, flat-sided case, so you can push the probe into food and turn the display to face you. A button cell runs a chip and a liquid crystal display, and a push button updates the reading at once. The angled case will not roll off a table.
Result: a thin-probe digital thermometer for food and air.
Source: T. A. Cook (PSG Industries), US 5,018,875 (1991). Unknown: the circuit, the range, the case size. Picture: the patent drawing.
Menengah
Unknown
Instruksi
1
1
Make the probe
Make the probe
Cut a type 304 stainless steel tube about 0.166 in (4.0 mm) across and 5 in (120 mm) long, and close one end. Set a thermistor inside the closed tip and run its two wires up the tube. Aluminium or titanium would also serve.
Material untuk langkah ini:
Pipa baja nirkarat1 probe
Set termistor NTC1 thermistor
Kawat Tembaga1 interconnecting wiresAlat yang dibutuhkan:
Gergaji Besi
Solder2
2
Mould the pivot boss and case
Mould the pivot boss and case
Mould from ABS a cylindrical pivot boss with a recess for the probe's open end and a channel right through it for the wires. Mould the case in an upper and a lower half that snap together, wider at the display end and tapering to the probe end so it cannot roll, with two projecting supports at the probe end, each with a pivot hole. Not given: the sizes.
Material untuk langkah ini:
Pelet ABS1 boss and caseAlat yang dibutuhkan:
Mesin cetak injeksi
Dimensi tidak diketahui3
3
Fit the electronics and assemble
Fit the electronics and assemble
In the case, fit an integrated circuit that turns the thermistor's resistance into a reading on a liquid crystal display at the wide end, with a push button beside it that updates the reading at once. Add a compartment for a 1.5 V button cell (Eveready E675, IEC R07) under a cover that locks with a quarter turn. Push the probe into the boss, lead the wires through the channel to the circuit, and clamp the boss ends in the pivot holes as the halves snap together; friction holds whatever angle you set. In use, push the probe in, turn the display to face you and press the button. Not given: the circuit (the patent points to US 4,536,851).
Material untuk langkah ini:
Papan sirkuit cetak1 buah
Sirkuit terpadu1 buah
Panel LCD segmen1 buah
Tombol tekan1 buah
Baterai kancing 1,5 V1 buah
Kawat Timah Solder1 as neededAlat yang dibutuhkan:
SolderBahan
10- 1 probePlaceholder
- 1 thermistorPlaceholder
- 1 interconnecting wiresPlaceholder
- 1 boss and casePlaceholder
- 1 buahPlaceholder
- 1 buahPlaceholder
- 1 buahPlaceholder
- Placeholder
- 1 buahPlaceholder
- 1 as neededPlaceholder
Alat yang Diperlukan
4- Placeholder
- 2 vendors sell this, none ship to you yetPlaceholder
- Placeholder
- Placeholder
Bahan cetak biru terhubung
Cetak biru ini membuat
Blueprint terkait
Blueprint ini berbagi pengetahuan — teknik, bahan, atau prinsip
CC0 Domain Publik
Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.
Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.



