Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Forged Square-Neck Door Bolt and Nut, Threaded with a Screw-Plate (Moxon, 1677)
Forge

Dibuat oleh

Forge

14. November 2026NO
9
0
0
0
0

Forged Square-Neck Door Bolt and Nut, Threaded with a Screw-Plate (Moxon, 1677)

Joseph Moxon's 1677 way to make the screw bolt for a door: a square iron bar forged down to a square neck and round pin, the head cut off with a chisel, the pin threaded with a screw-plate, and a punched iron nut threaded with a tap. The square neck sits in a square hole so the bolt cannot turn while the nut is tightened.
Menengah
About an hour per bolt

Instruksi

1

Choosing the hole

Memuat notebook Jupyter…
2

Read Mechanick Exercises

"The Shank of the Screw for Doors and many other purposes must be Forged square near the Head, because it must be let into a square hole that it may not twist about when the Nut is turned about hard upon the Screw-Pin."
3

Forge the square neck

Take a square iron bar as near the size of the head as you can. At a flame (white) heat lay the shank length flat on the near side of the anvil and hammer it down to thickness; do not strike over the edge or you cut the iron. Reheat, turn it, and hammer the other two sides close up to the head.

Material untuk langkah ini:

Batang besi tempaBatang besi tempa1 buah

Alat yang dibutuhkan:

Perapian pandai besiPerapian pandai besi
Landasan TempaLandasan Tempa
PaluPalu
Tang pandai besiTang pandai besi
4

Round the pin, cut the head

Hammer down the corners of the part meant for the thread and round it. Set the chisel at the head thickness, strike half through, turn and cut each side half through until it comes off. Square the shoulder: reheat, grip in square-nosed tongs, set the shank in the vice with the shoulder on the jaws, and hammer the head.

Alat yang dibutuhkan:

Perapian pandai besiPerapian pandai besi
Pahat potong landasanPahat potong landasan
Tang pandai besiTang pandai besi
Ragum bangku beratRagum bangku berat
PaluPalu
5

Punch the nut

Forge a nut blank from the bar. Harden the point of a steel punch of the hole's size (no tempering: the hot iron softens it). At a blood-red heat punch from one side until the far side bulges, turn it, set it flat, and punch through over the hole of a bolster. Dip the punch in water whenever it changes colour. Let forged work cool on the floor or hearth; never quench it.

Material untuk langkah ini:

Batang besi tempaBatang besi tempa1 buah

Alat yang dibutuhkan:

Perapian pandai besiPerapian pandai besi
Landasan TempaLandasan Tempa
Pelubang panasPelubang panas
PaluPalu
Ember pendingin tempaEmber pendingin tempa
Tang pandai besiTang pandai besi
6

Thread the pin

File the shank and head, file the pin round, and taper its end by the depth of the screw-plate's threads. Find the screw-plate hole the pin just slides through, turn the pin in it, and file off the marks it cuts: the pin is then true. Set the bolt head down in the vice, press the next smaller hole (groove diameter equal to the pin) hard down on it, and turn the plate evenly.

Alat yang dibutuhkan:

Kikir (Kikir Tangan)Kikir (Kikir Tangan)
Ragum bangku beratRagum bangku berat
Set pembuat ulirSet pembuat ulir
7

Tap the nut

Fit the tap to the round hole of the nut; it must match the pin (try it in the same screw-plate hole). Set the nut flat in the vice and turn the tap hard round by its handle, or by the square hole near the screw-plate handle, until it cuts the thread.

Alat yang dibutuhkan:

Ragum bangku beratRagum bangku berat
Set pembuat ulirSet pembuat ulir
8

Troubleshooting

Screw bolt troubleshooting.

Flow

Loading...
9

History and honest limits

From Joseph Moxon, **Mechanick Exercises, or the Doctrine of Handy-Works** (1677), Smithing, Numb. I pp. 10-11 and Numb. II pp. 29-31 (checked on the archive.org scan mechanickexercis00moxo). He gives no sizes or nut shape; the metric example and the tool heads are ours.

Bahan

1

Alat yang Diperlukan

10

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...