Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Platform Scale: Four Knife-Edge Hinges and Two Levers to a Steelyard (Fairbanks, 1831)
Mark

Dibuat oleh

Mark

2. November 2026FI
9
0
0
0
0

Platform Scale: Four Knife-Edge Hinges and Two Levers to a Steelyard (Fairbanks, 1831)

A scale for wagons and carts, reading the same wherever the load stands. Erastus and Thaddeus Fairbanks of St. Johnsbury, Vermont, patented it in 1831. A plank platform nine by twelve feet rests on four knife-edge hinges, one at each corner, and two levers gather the load from all four onto one rod. The rod pulls on an ordinary steelyard, which then reads only a tenth or a twentieth of the load. Result: a platform scale reading ten times (or twenty times) what the steelyard shows, the same wherever the load stands on the platform. Source: E. & T. Fairbanks, US Patent No. 118 (1837), restating their patent of 13 June 1831. Unknown: the material and sizes of the hinges, knife-edges, fulcra and levers. Picture: patent drawing.
Lanjutan
1 week

Instruksi

1

Build the frame

Lay two timber bed-sills, about 10 inches square and 16 feet long, parallel and about 7 feet apart. Bolt two end timbers, 8 by 14 inches and 12 feet long, across them near their ends. Just inside the end timbers, lay the two rockers, 8 inches square and 9 feet long, with their tops flush with the end timbers. Ours: carriage bolts.

Material untuk langkah ini:

Kayu balok persegiKayu balok persegi6 2 sills, 2 end timbers, 2 rockers
Baut kepala bulat leher persegiBaut kepala bulat leher persegi1 set

Alat yang dibutuhkan:

Gergaji lintang dua orangGergaji lintang dua orang
Bor tanahBor tanah
PaluPalu
2

Fit the four knife-edge hinges

Bolt a hinge firmly under each end of each rocker, one at every corner of the machine. Each hinge carries two knife-edges. One rests on a fulcrum standing on the bed-sill; the other reaches out to carry the platform. Set every knife-edge parallel to the others: knife-edges at an angle cramp and bind. Not given: the material and size of the hinges, knife-edges and fulcra.

Material untuk langkah ini:

Bahan tidak diketahuiBahan tidak diketahui1 4 hinges, 8 knife-edges, 4 fulcra
Baut kepala bulat leher persegiBaut kepala bulat leher persegi1 set

Alat yang dibutuhkan:

Bor tanahBor tanah
Dimensi tidak diketahuiDimensi tidak diketahui
3

Join the levers

Run a horizontal lever from each rocker. The longer lever reaches across nearly to the opposite rocker. The shorter one ends at a point equally far from the axes of both, and hangs there from the longer lever by a chain, rod or stirrup, so the two act as one. From the end of the longer lever a rod rises straight up to a steelyard hung from a fixed support. With the two knife-edges of each hinge 6 inches apart and the rod hung 60 inches from the lever's axis, the load is ten times the steelyard reading; at 120 inches it is twenty times. Not given: the lever material. Ours: an iron chain and a wrought iron rod.

Material untuk langkah ini:

Bahan tidak diketahuiBahan tidak diketahui1 2 levers
Rantai besiRantai besi1 lever link
Tongkat besi tempaTongkat besi tempa1 rod to the steelyard
DacinDacin1 buah

Alat yang dibutuhkan:

Dimensi tidak diketahuiDimensi tidak diketahui
4

Lay the platform

Lay two timbers, short enough to pass freely between the rockers, parallel over the bed-sills. Spike stout planks 9 feet long across them, making a platform of about 9 by 12 feet. Under these timbers fasten iron plates that rest on the inner knife-edges of the hinges. Ours: nails as the spikes.

Material untuk langkah ini:

Kayu balok persegiKayu balok persegi2 platform timbers
Papan kayuPapan kayu1 for 9 x 12 ft
Pelat besiPelat besi4 buah
PakuPaku1 as needed

Alat yang dibutuhkan:

Gergaji lintang dua orangGergaji lintang dua orang
PaluPalu

Bahan

9

Alat yang Diperlukan

4

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...