Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Roberval Balance: a Parallelogram Frame That Keeps Both Pans Level (Roberval, 1669)
Penny

Dibuat oleh

Penny

2. November 2026DK
10
0
0
3
0

Roberval Balance: a Parallelogram Frame That Keeps Both Pans Level (Roberval, 1669)

The equal-arm balance rebuilt as a hinged frame. Gilles Personne de Roberval showed it to the Académie Royale des Sciences in 1669. Two bars pivot on a post, joined at their ends by two upright bars into a hinged rectangle; each pan is fixed to an upright, so it stays level as the frame tilts. Result: a balance on which a weight weighs the same wherever it sits on its pan, even when both loads are on the same side of the post. Later shop scales of the Roberval type keep this frame. Source: the 1670 Journal des savants account as given by J. F. Hall, Two Hundred Years of Analyzing Roberval's Balance, Caltech Report 2024-01. Unknown: materials and sizes. Picture: Wikimedia Commons.
Menengah
1 day

Instruksi

1

Make the six frame pieces and the post

Make a post standing on a pedestal, a top bar and a bottom bar of the same length, and two upright bars of the same length as each other. Mark each horizontal bar at its exact middle: its two arms must be equal. Make two flat platforms (the pans). Not given: the material and the sizes.

Material untuk langkah ini:

Bahan tidak diketahuiBahan tidak diketahui1 bars, post, pedestal, platforms

Alat yang dibutuhkan:

Dimensi tidak diketahuiDimensi tidak diketahui
2

Pin the frame to the post

Pin the top bar to the post at its middle, and the bottom bar to the post at its middle, directly below, so both can turn. Pin the left upright to the left ends of both bars, and the right upright to the right ends. The four bars now form a rectangle that can lean into a parallelogram; the uprights always stay upright. Tight pins bind unless every length is exact, so Hall advises slotting the lower hole in the post upright: it may slide up and down but not sideways. Ours: drill the pin holes by hand.

Material untuk langkah ini:

Bahan tidak diketahuiBahan tidak diketahui1 six pins

Alat yang dibutuhkan:

Bor tanganBor tangan
3

Fix the pans to the uprights

Fix one platform rigidly to each upright, so it cannot turn. The weights sit on the platforms or hang from them. As the frame tilts, the uprights move straight up and down and the platforms stay level.

Material untuk langkah ini:

Bahan tidak diketahuiBahan tidak diketahui1 fixings
4

Test it

With the pans empty the frame should rest level. Put equal weights on the two pans: they balance. Now slide one weight to the edge of its pan, or to the far side of the post: they still balance. With unequal arms, weights balance when their ratio is the inverse of the arm lengths.

Alat yang dibutuhkan:

PemberatPemberat

Bahan

1

Alat yang Diperlukan

3

Blueprint terkait

Blueprint ini berbagi pengetahuan — teknik, bahan, atau prinsip

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...