SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Potentiometer: Podolsky Roller-Contact Unit in a Moulded Casing
Podolsky's variable resistor (Wirt Company, US 2,060,114, 1936). The carbon strip is bent into a ring inside a moulded casing, and instead of a sliding wiper a small roller runs round it. A coil spring presses the roller out against the strip with even pressure in every position, even over slight irregularities. The patent gives no sizes; the parts are named by what they do.
The picture: the patent's drawing (Figs. 8 and 9).
Menengah
2 hours
Instruksi
1
1
Seat the strip in the casing
Seat the strip in the casing
Bend the resistance strip into a ring against the round inner wall of the moulded casing. A small rib across the wall stops both ends of the strip so it cannot shift; the thick part at the rib has a hole for bolting the casing to a panel. Ours: flat-nose pliers to ease the strip in.
Material untuk langkah ini:
Moulded Insulating Casing1 buah
Elemen Resistansi Karbon1 buahAlat yang dibutuhkan:
Tang Berujung Rata2
2
Bolt the terminals
Bolt the terminals
Put two terminal bolts through the casing wall, one at each end of the strip. Under each bolt head a small contact plate rests on the coated end of the strip.
Material untuk langkah ini:
Baut Terminal2 buah
Contact Plate2 buahAlat yang dibutuhkan:
Tang lancip3
3
Fit shaft, sleeve, collar and yoke
Fit shaft, sleeve, collar and yoke
The shaft turns in a sleeve fixed in the base of the casing. A collar on the shaft rests on the outer end of the sleeve; on the inner end the shaft carries a yoke, with a spring washer between yoke and sleeve so the shaft cannot slide. Ours: pliers to seat the spring washer.
Material untuk langkah ini:
Poros Kendali1 buah
Shaft Sleeve1 buah
Shaft Collar1 buah
Shaft Yoke1 buah
Spring Washer1 buahAlat yang dibutuhkan:
Tang lancip4
4
Fit the sprung roller
Fit the sprung roller
The yoke's slotted ends guide a flat stem. The roller sits in the stem's forked outer end. A washer on shoulders of the stem, pushed out by a coil spring, holds the roller on the strip with even pressure all the way round.
Material untuk langkah ini:
Roller Stem1 buah
Contact Roller1 buah
Ring Rata1 buah
Coil Spring1 buahAlat yang dibutuhkan:
Tang lancipBahan
13- Placeholder
- 1 buahPlaceholder
- 2 buahPlaceholder
- 2 buahPlaceholder
- 1 buahPlaceholder
- 1 buahPlaceholder
- 1 buahPlaceholder
- 1 buahPlaceholder
- 1 buahPlaceholder
- 1 buahPlaceholder
- 1 buahPlaceholder
- 1 buahPlaceholder
- 1 buahPlaceholder
Alat yang Diperlukan
2- Placeholder
- Placeholder
Cetak biru ini membuat
Blueprint terkait
Blueprint ini berbagi pengetahuan — teknik, bahan, atau prinsip
CC0 Domain Publik
Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.
Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.