Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Swing-Nut Tubing Cutter: Swing the Blade Support Down and the Jaw Slides to the Tube, Up and the Screw Feeds It (Pritchard, 1941)
Forge

Dibuat oleh

Forge

13. November 2026NO
13
0
0
0
0

Swing-Nut Tubing Cutter: Swing the Blade Support Down and the Jaw Slides to the Tube, Up and the Screw Feeds It (Pritchard, 1941)

Frank L. Pritchard of Parker, Arizona, received US 2,231,593, dated 11 February 1941, for a tubing cutter small enough for a mechanic's tool box. The tube sits in a V in a fixed jaw. A movable jaw slides on the adjusting screw and a guide pin, with a spring pushing the jaws apart. The cutting wheel is held by a pivoted support with threads on its inner edge. Swung down, the support lets go of the screw, so the jaw can be pushed straight onto any tube. Swung up, it meshes with the screw again and the screw feeds the wheel in. We make his parts from steel bar and plate. All sizes are ours.
Menengah
About 3 days

Instruksi

1

The swing that lets go

Memuat notebook Jupyter…
2

Read US 2,231,593

"The pivoted blade support 16 may swing downwardly until the threads thereof will be free of the threads of the screw 8. The movable jaw 6 may now be slid downwardly until the pivoted blade support is in its proper cutting position."
3

Print the template

Both jaws, the blade support, the wheel and a 15 mm tube at 1:1, with the screw, pin and pivot holes. print at 100 % (check the 50 mm bar).
Berkas desainPDFCC0 - Free
4

Make the stationary jaw

Saw 64 mm of 16 mm square bar, or of 16 mm plate. File the 90 degree V 8 mm deep in its top face. Drill the 6 mm pin hole and a 10 mm hole for the screw, and counterbore the pin hole 10 mm across, 5 mm deep, for the spring. Drill the 3 mm cross-pin hole across the jaw so it just cuts into the side of the screw hole.

Material untuk langkah ini:

Pelat baja lunakPelat baja lunak1 buah

Alat yang dibutuhkan:

Gergaji BesiGergaji Besi
Set KikirSet Kikir
Mesin Bor DudukMesin Bor Duduk
Ragum MesinRagum Mesin
Set Mata BorSet Mata Bor
PenitikPenitik
PenggoresPenggores
Ragum MejaRagum Meja
Jangka Sorong Digital 6 InciJangka Sorong Digital 6 Inci
5

Make the movable jaw and the support

Saw the movable jaw 50 mm long from the same bar. Drill the 6.2 mm pin hole and its spring counterbore. Saw and file a slot 8.2 mm wide down its middle, from 22 mm to the end. Saw the blade support from 14 mm plate to the template. File its upper part down to 8 mm thick, centred, so it slides into the slot, and file away its lower inner corner. Saw a 7 mm slot up its lower part for the wheel. Drill the pivot and stop-pin holes through the jaw and support together, and file the stop-pin hole in the support into a short slot.

Material untuk langkah ini:

Pelat baja lunakPelat baja lunak1 buah

Alat yang dibutuhkan:

Gergaji BesiGergaji Besi
Set KikirSet Kikir
Set Kikir JarumSet Kikir Jarum
Mesin Bor DudukMesin Bor Duduk
Ragum MesinRagum Mesin
Set Mata BorSet Mata Bor
Ragum MejaRagum Meja
Jangka Sorong Digital 6 InciJangka Sorong Digital 6 Inci
6

Tap the half nut

Pin the support in the jaw, swung up, and clamp it there. Drill 6.8 mm down the screw axis through both, so the drill cuts a shallow groove in the support's inner edge, then tap it M8 through both. Take the support out and open the jaw's own hole to 8.5 mm, so the screw passes freely and only the support's threads hold it.

Alat yang dibutuhkan:

Mesin Bor DudukMesin Bor Duduk
Ragum MesinRagum Mesin
Set Mata BorSet Mata Bor
Set pembuat ulirSet pembuat ulir
Minyak potongMinyak potong
7

Make the screw and the guide pin

Turn the top 62 mm of a 90 mm piece of 10 mm bar to 8 mm and cut an M8 thread on it with the die. Turn a groove 1.5 mm deep and 3.2 mm wide in the plain part, where the cross pin will sit, and drill a 6 mm hole across its bottom end for a T-bar. Cut the guide pin, 80 mm of 6 mm rod, and drill a 3 mm hole across its top for the stop pin.

Material untuk langkah ini:

Batang bulat baja lunakBatang bulat baja lunak1 buah
Batang Baja LunakBatang Baja Lunak1 buah

Alat yang dibutuhkan:

Mesin Bubut LogamMesin Bubut Logam
Cekam bubut 3 rahangCekam bubut 3 rahang
Pahat bubutPahat bubut
Pahat potong bubutPahat potong bubut
Set pembuat ulirSet pembuat ulir
Mesin Bor DudukMesin Bor Duduk
Set Mata BorSet Mata Bor
Gergaji BesiGergaji Besi
Jangka Sorong Digital 6 InciJangka Sorong Digital 6 Inci
8

Turn the cutting wheel

Chuck a tool steel bar and face it. Turn the end to 20 mm across for 10 mm, centre drill and drill a 5 mm hole 10 mm deep, and turn the edge to a 50 degree vee, 25 degrees each side, sharp in the middle of the 6 mm width. Part it off 6 mm long and take the burr off the hole.

Material untuk langkah ini:

Batang baja perkakasBatang baja perkakas1 buah

Alat yang dibutuhkan:

Mesin Bubut LogamMesin Bubut Logam
Cekam bubut 3 rahangCekam bubut 3 rahang
Pahat bubutPahat bubut
Pahat potong bubutPahat potong bubut
Set mata bor senterSet mata bor senter
Set Mata BorSet Mata Bor
Jangka Sorong Digital 6 InciJangka Sorong Digital 6 Inci
Kacamata pengamanKacamata pengaman
9

Harden and temper

Heat the wheel to a cherry red, until a magnet no longer sticks, and quench it in water, moving it about. Rub it bright with a stone, warm it on a piece of steel plate over the fire, and quench again as soon as it turns a light straw colour.

Alat yang dibutuhkan:

Tungku TempaTungku Tempa
Penjepit TempaPenjepit Tempa
Magnet KecilMagnet Kecil
Ember pendingin tempaEmber pendingin tempa
AirAir
Batu AsahBatu Asah
Sarung tangan lasSarung tangan las
Kacamata pengamanKacamata pengaman
10

Assemble

Drive the guide pin into the stationary jaw. Put the screw into its hole from below and drive the cross pin in so it lies in the groove; the screw must still turn. Fit the T-bar. Slip the spring over the guide pin, then the movable jaw over the pin and the screw, and put the stop pin across the top. Fit the wheel in the support on its 5 mm pin, and pin the support into the jaw with its pivot and stop pins. Rivet a 1.5 mm steel strip along the top of the jaw, sticking out past the support as a thumb piece. Oil the threads.

Material untuk langkah ini:

Pin pasak bajaPin pasak baja5 buah
Set Pegas TekanSet Pegas Tekan1 buah
Pita baja pegasPita baja pegas1 buah
Paku keling bajaPaku keling baja2 buah
Batang Baja LunakBatang Baja Lunak1 buah

Alat yang dibutuhkan:

Palu kepala bulatPalu kepala bulat
PenitikPenitik
Ragum MejaRagum Meja
Mesin Bor DudukMesin Bor Duduk
Set Mata BorSet Mata Bor
Minyak potongMinyak potong
11

Cut a copper tube

Mark a copper tube and hold it in a vice with soft jaws, or by hand for small tubes. Swing the support down, push the movable jaw down until the wheel touches the tube in the V, swing it up into the screw, and tighten the screw a little. Turn the cutter once round, give the screw about a quarter turn, and go on until the tube parts. The wheel should run in its own groove; the end should be square and not squeezed oval. Clean the inside of the end with a deburring tool.

Material untuk langkah ini:

Pipa tembagaPipa tembaga1 buah

Alat yang dibutuhkan:

Ragum MejaRagum Meja
Alat penghilang duri sisaAlat penghilang duri sisa
Jangka Sorong Digital 6 InciJangka Sorong Digital 6 Inci
12

Troubleshooting

Swing-nut tubing cutter troubleshooting.

Flow

Loading...
13

History and honest limits

**Frank L. Pritchard** of Parker, Arizona, US 2,231,593, dated 11 February 1941, filed 17 November 1939. He claimed "a pivoted blade support mounted on the movable jaw and having threads on the inner edge thereof adapted to engage the threads of said screw". His movable jaw had a bushing for the guide pin and a looped handle on the screw head; ours has a drilled hole and a T-bar. The patent gives no sizes or materials; all of ours are ours.

Bahan

9

Alat yang Diperlukan

27

Berkas desain

1

Cetak biru ini membuat

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...