Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
V-Slide Tubing Cutter: Two Slide Halves Held on the Ways by One Spring Clip, a Reamer on the Frame (Thewes, 1938)
Forge

Dibuat oleh

Forge

13. November 2026NO
13
0
0
0
0

V-Slide Tubing Cutter: Two Slide Halves Held on the Ways by One Spring Clip, a Reamer on the Frame (Thewes, 1938)

William O. Thewes of North Ridgeville, Ohio, received US 2,130,934, dated 20 September 1938 and assigned to The Ridge Tool Company, for a cutter for thin copper and brass tubing. A C-frame carries a cutting wheel at one end and a feed screw at the other. The screw pushes a V-slide that holds the tube against the wheel. The slide is two halves on ways along the frame, held together by one V-shaped spring clip, which is also the face the tube bears on. A triangular reamer on the side of the frame cleans the cut end, and the frame is its handle. We saw the frame from steel plate and pin the reamer in. His parts were die cast. All sizes are ours.
Menengah
About 3 days

Instruksi

1

Where the tube sits

Memuat notebook Jupyter…
2

Read US 2,130,934

"With my improved cutter the ways or guides are integral with the frame and are uninterrupted throughout the length of the frame, and the slide is held in close sliding engagement on the ways without the use of bolts or rivets."
3

Print the template

Frame, slide half, end section, reamer and clip blank at 1:1 on A4, with the 8 and 28 mm tubes drawn in. print at 100 % (check the 50 mm bar).
Berkas desainPDFCC0 - Free
4

Saw out the frame

Glue the frame outline on 16 mm plate. Drill a row of holes inside the C, saw to them, and file to the line. Saw the 7 mm wheel slot down through the wheel post with two cuts, break out the middle and file it flat. Drill the 5 mm wheel pin and 4 mm tie pin holes across the slot. Drill 8.5 mm along the screw axis through the other post and tap it M10.

Material untuk langkah ini:

Pelat baja lunakPelat baja lunak1 buah

Alat yang dibutuhkan:

Gergaji BesiGergaji Besi
Set KikirSet Kikir
Mesin Bor DudukMesin Bor Duduk
Ragum MesinRagum Mesin
Set Mata BorSet Mata Bor
Set pembuat ulirSet pembuat ulir
PenitikPenitik
PenggoresPenggores
Ragum MejaRagum Meja
Minyak potongMinyak potong
5

File the ways

Along the bottom bar, between the posts, file a groove 2 mm deep and 4 mm high in both faces, 3 mm below the top edge. This leaves a T-shaped rib along the top: the ways. Keep it straight and the same all along, so the slide runs smoothly from end to end.

Alat yang dibutuhkan:

Set KikirSet Kikir
Set Kikir JarumSet Kikir Jarum
Ragum MejaRagum Meja
Jangka Sorong Digital 6 InciJangka Sorong Digital 6 Inci
6

Turn the cutting wheel

Chuck a tool steel bar and face it. Turn the end to 20 mm across for 10 mm, centre drill and drill a 5 mm hole 10 mm deep, and turn the edge to a 50 degree vee, 25 degrees each side, sharp in the middle of the 6 mm width. Part it off 6 mm long and take the burr off the hole.

Material untuk langkah ini:

Batang baja perkakasBatang baja perkakas1 buah

Alat yang dibutuhkan:

Mesin Bubut LogamMesin Bubut Logam
Cekam bubut 3 rahangCekam bubut 3 rahang
Pahat bubutPahat bubut
Pahat potong bubutPahat potong bubut
Set mata bor senterSet mata bor senter
Set Mata BorSet Mata Bor
Jangka Sorong Digital 6 InciJangka Sorong Digital 6 Inci
Kacamata pengamanKacamata pengaman
7

Make the reamer

Saw a triangle with 22 mm sides from 3 mm flat tool steel and drill its 4 mm hole. Grind each edge to a 60 degree bevel from both sides, so all three edges cut. Saw a 3 mm wide slot, 22 mm long and 8 mm deep, in the middle of the frame's bottom edge, 50 mm from the wheel end, and drill the 4 mm pin hole across it.

Material untuk langkah ini:

Batang baja perkakas pipihBatang baja perkakas pipih1 buah

Alat yang dibutuhkan:

Gergaji BesiGergaji Besi
Gerinda dudukGerinda duduk
Mesin Bor DudukMesin Bor Duduk
Set Mata BorSet Mata Bor
Set KikirSet Kikir
Kacamata pengamanKacamata pengaman
8

Harden and temper

Heat the wheel and the reamer to a cherry red, until a magnet no longer sticks, and quench it in water, moving it about. Rub it bright with a stone, warm it on a piece of steel plate over the fire, and quench again as soon as it turns a light straw colour.

Alat yang dibutuhkan:

Tungku TempaTungku Tempa
Penjepit TempaPenjepit Tempa
Magnet KecilMagnet Kecil
Ember pendingin tempaEmber pendingin tempa
AirAir
Batu AsahBatu Asah
Sarung tangan lasSarung tangan las
Kacamata pengamanKacamata pengaman
9

Make the slide halves

Saw two pieces of 10 mm plate to the slide outline, one the mirror of the other, and file the V. On the inner face of each, saw and file a pocket for half the screw head and a slot for its neck. Saw and file a step along the bottom edge of each half so its lip fits the groove under the ways (end section on the template). File a shallow notch in the outer face of each half, beside the V, for the clip's tongues.

Material untuk langkah ini:

Pelat baja lunakPelat baja lunak1 buah

Alat yang dibutuhkan:

Gergaji BesiGergaji Besi
Set KikirSet Kikir
Set Kikir JarumSet Kikir Jarum
Ragum MejaRagum Meja
Jangka Sorong Digital 6 InciJangka Sorong Digital 6 Inci
PenggoresPenggores
10

Bend the V clip

Cut the clip blank from 0.5 mm spring steel strip. Bend the four tongues up at right angles, then fold the blank to 90 degrees on the dashed line, over the slide's V.

Material untuk langkah ini:

Pita baja pegasPita baja pegas1 buah

Alat yang dibutuhkan:

Gergaji BesiGergaji Besi
Set KikirSet Kikir
Ragum MejaRagum Meja
Palu kepala bulatPalu kepala bulat
11

Make the feed screw

Cut 120 mm of M10 threaded rod. Chuck it and turn the end to a 9 mm head 4 mm long on a 6 mm neck 3 mm long. Drill a 6 mm hole across the other end and push a 70 mm piece of 6 mm rod through it for the T-handle. Peen it both sides so it stays put.

Material untuk langkah ini:

Batang berulirBatang berulir1 buah
Batang Baja LunakBatang Baja Lunak1 buah

Alat yang dibutuhkan:

Mesin Bubut LogamMesin Bubut Logam
Cekam bubut 3 rahangCekam bubut 3 rahang
Pahat bubutPahat bubut
Pahat potong bubutPahat potong bubut
Mesin Bor DudukMesin Bor Duduk
Set Mata BorSet Mata Bor
Palu kepala bulatPalu kepala bulat
Gergaji BesiGergaji Besi
12

Assemble

Fit the wheel in its slot with the 5 mm pin, and the 4 mm tie pin above it, peened. Tap the reamer into its slot and pin it. Screw the feed screw through the boss. Put the halves on the ways from the sides, closing them round the screw head, and spring the clip over their V so its tongues snap into the notches. Oil the ways and the screw.

Material untuk langkah ini:

Pin pasak bajaPin pasak baja3 buah

Alat yang dibutuhkan:

Palu kepala bulatPalu kepala bulat
PenitikPenitik
Ragum MejaRagum Meja
Minyak potongMinyak potong
13

Cut a copper tube

Mark a copper tube and hold it in a vice with soft jaws, or by hand for small tubes. Open the screw, drop the cutter over the tube, and screw the slide in until the wheel just touches. Turn the cutter once round, give the screw about a quarter turn, and go on until the tube parts. The wheel should run in its own groove; the end should be square and not squeezed oval. Clean the inside of the end with a deburring tool.

Material untuk langkah ini:

Pipa tembagaPipa tembaga1 buah

Alat yang dibutuhkan:

Ragum MejaRagum Meja
Alat penghilang duri sisaAlat penghilang duri sisa
Jangka Sorong Digital 6 InciJangka Sorong Digital 6 Inci
14

Ream the end

Hold the frame like a T-handle, put the reamer's point in the cut end, and turn it a few times to take off the fin the wheel has turned in.

Alat yang dibutuhkan:

Ragum MejaRagum Meja
15

Troubleshooting

Tubing cutter troubleshooting.

Flow

Loading...
16

History and honest limits

**William O. Thewes** of North Ridgeville, Ohio, US 2,130,934, dated 20 September 1938, filed 4 November 1935, assigned to The Ridge Tool Company. Earlier slides needed notched ways, which weaken the frame, or bolts that come loose; he claimed "a V block reciprocable on the guideway and comprising two sections, and a face plate clamping said sections together". A later certificate corrects "same" to "frame" and "base" to "boss". His frame and slide were die cast and the reamer cast into the frame; ours are sawn from plate and the reamer is pinned. The patent gives no sizes; all of ours are ours.

Bahan

8

Alat yang Diperlukan

28

Berkas desain

1

Cetak biru ini membuat

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...