Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Rack-and-Pinion Router With a Zero-Set Knob: Two Knobs on One Hollow Pinion, Set to Zero on the Work (Rees, 1969)
Forge

Dibuat oleh

Forge

13. November 2026NO
7
0
0
0
0

Rack-and-Pinion Router With a Zero-Set Knob: Two Knobs on One Hollow Pinion, Set to Zero on the Work (Rees, 1969)

Spencer C. Rees of Pickens, South Carolina, received US 3,466,973, dated 16 September 1969, for The Singer Company. A rack screwed to the motor housing is moved by a pinion through a window in a box on the base. The pinion is a hollow shaft running in one bore through the box's two side lugs, with a knob at each end. One knob turns it. The other, a zero-set knob with graduations, slips on its sleeve against an O-ring, so it can be set to zero with the bit touching the work. One screw through the middle holds it all together. Only the pinion shaft was metal; the rest was moulded. We print every part in PETG round a small DC motor. The sizes are ours.
Lanjutan
About 3 days

Instruksi

1

What one turn of the knob does

Memuat notebook Jupyter…
2

Read US 3,466,973

"The zero-set knob 40 has a reduced diameter portion 51 which carries circumferentially-spaced graduation marks 52 on its surface." "In the above-described structure it will be noted that the only metallic part required is the pinion shaft 37 which is a relatively simple two-diameter piece."
3

Print the base

The base 10: the split ring with clamp lugs, the box 28 for the rack with its two lugs 50 and stepped bore 33, the window 36, two legs 11 down to the plate 12 with its aperture, and two handle arms. Print it plate down. PETG, 0.2 mm layers, 40 % infill, 5 walls.
Berkas desainSTLCC0 - Free
4

Print the motor housing

The housing 19: a tube for a 42 mm motor, 56 mm outside, a ledge with an 18 mm hole and two M4 holes, and two M3 holes for the rack. Print it ledge down. PETG, 0.2 mm layers, 40 % infill, 5 walls.
Berkas desainSTLCC0 - Free
5

Print the small parts

One plate: the rack 29 (module 1.5), the hollow pinion shaft 37 with its toothed (splined) part, bearing part and end ribs, the adjusting knob 38 with grooves, the flanged sleeve 39, the zero-set knob 40 with 20 graduations and an O-ring groove, and the cover plate 53 with its window 55 and mark 56. PETG, 0.2 mm layers, 40 % infill, 5 walls.
Berkas desainSTLCC0 - Free
6

Motor in the housing

Fit the collet adapter on the motor's shaft, stand the motor in the housing on its ledge and screw it down with two M4 screws; wire it through a toggle switch to the DC supply. Screw the rack to the housing's front with two M3 screws.

Material untuk langkah ini:

Filamen PETGFilamen PETG1 buah
Motor listrikMotor listrik1 buah
Adaptor kolet poros motorAdaptor kolet poros motor1 buah
Sekrup Kepala SoketSekrup Kepala Soket2 buah
Sekrup mesinSekrup mesin2 buah
Sakelar tuasSakelar tuas1 buah
Kawat hubungKawat hubung1 buah
Selongsong bakarSelongsong bakar1 buah

Alat yang dibutuhkan:

Pencetak 3D filamen (FDM)Pencetak 3D filamen (FDM)
Sumber daya arus searahSumber daya arus searah
Solder ListrikSolder Listrik
Set kunci LSet kunci L
Set obengSet obeng
Alat penghilang duri sisaAlat penghilang duri sisa
7

Base and handles

Turn two hardwood handles 17 and bolt one to each arm with an M8 bolt. Slide the housing into the base with the rack in the box's channel, and put an M5 screw with a wing nut through the clamp lugs.

Material untuk langkah ini:

Papan Kayu KerasPapan Kayu Keras1 buah
Aneka baut segi enamAneka baut segi enam2 buah
Mur Segi EnamMur Segi Enam3 buah
Sekrup Kepala SoketSekrup Kepala Soket1 buah
Mur sayapMur sayap1 buah

Alat yang dibutuhkan:

Mesin bubut kayuMesin bubut kayu
Bor Tanpa KabelBor Tanpa Kabel
Set Mata BorSet Mata Bor
Kunci InggrisKunci Inggris
8

Pinion, knobs and cover

Push the pinion shaft through the box's bore from the right, its toothed part through the window meshing with the rack, its bearing part in the right lug. Fit the O-ring in the zero-set knob's groove, push the sleeve into the knob, and slide them onto the shaft's toothed end from the left, the sleeve in the left lug. Fit the adjusting knob on the right end, its grooves on the shaft's ribs. Pass a long M4 screw through knob, shaft and sleeve with a washer, into a nut in the sleeve, and tighten it until the knobs have only a little end play. Screw the cover over the box with two M3 screws.

Material untuk langkah ini:

O-ringO-ring1 buah
Sekrup Kepala SoketSekrup Kepala Soket1 buah
Ring RataRing Rata1 buah
Mur Segi EnamMur Segi Enam1 buah
Sekrup mesinSekrup mesin2 buah

Alat yang dibutuhkan:

Set kunci LSet kunci L
Set obengSet obeng
9

Set zero and rout

Fit a bit. Loosen the clamp, turn the adjusting knob until the bit's tip touches the work, then turn the zero-set knob alone until its zero lines up with the cover's mark. Turn the adjusting knob to the depth wanted, read off the graduations, and clamp. Rout with both hands on the handles.

Alat yang dibutuhkan:

Set mata mesin profilSet mata mesin profil
Papan Kayu KerasPapan Kayu Keras
Klem batangKlem batang
Jangka Sorong Digital 6 InciJangka Sorong Digital 6 Inci
Kacamata pengamanKacamata pengaman
10

Troubleshooting

Rack and pinion router troubleshooting.

Flow

Loading...
11

History and honest limits

**Spencer C. Rees** of Pickens, South Carolina, assignor to The Singer Company, US 3,466,973, dated 16 September 1969, filed 8 January 1968. He claimed a rack on the motor housing, "a pair of lugs formed on the base in fixed spaced relation on opposite sides of the rack and having aligned cylindrical apertures", a hollow pinion shaft, an adjusting knob, a flanged sleeve, "a zero-set knob frictionally coupled to said sleeve", and "single fastening means" through them all. His pinion shaft was metal and the rest moulded; ours is all printed. His motor ran on mains; ours is a small DC motor. He gives no sizes; every size here is ours.

Bahan

14

Alat yang Diperlukan

15

Berkas desain

3

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...