Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Three-Legged Router: A T-Frame on the Table Beside the Work, Its Depth Set by a Knob While Cutting (Willard & Young, 1939)
Forge

Dibuat oleh

Forge

13. November 2026NO
7
0
0
0
0

Three-Legged Router: A T-Frame on the Table Beside the Work, Its Depth Set by a Knob While Cutting (Willard & Young, 1939)

Homer E. Willard and Frederick S. Young of Toledo, Ohio, received US 2,146,458, dated 7 February 1939, for a simple portable router with few moving parts. The motor sits in an open-fronted support in the middle of a T-shaped frame, so the bit and the work are always in view. The frame stands on three legs on the table beside the clamped work: two curved legs at one end, and at the other a screw with a knob. Turning the knob with one hand raises or lowers the bit while it cuts. We print the frame in PETG round a small DC motor. The sizes are ours.
Menengah
About 1 day

Instruksi

1

Depth by the knob

Memuat notebook Jupyter…
2

Read US 2,146,458

"Thus, by turning the wrist in one direction or the other, the bit 19 may be raised or lowered, as required, without stopping the motor and without removing the hands from the tool."
3

Print the frame

The T-shaped frame 10: the motor support 13 with its ledge 14 (an 18 mm hole and two M4 holes 29 mm apart) and curved wall 15, open at the front 16; arm 11 to the cross with two curved legs 21, 22; arm 12 to a boss with an M10 nut trap for the screw leg 24. PETG, 0.2 mm layers, 40 % infill, 5 walls; print it legs up, ledge on the bed.
Berkas desainSTLCC0 - Free
4

Fit the motor

Print the frame. Fit the collet adapter on the motor's shaft, stand the motor in the support with its face on the ledge and the collet through the hole, and screw it down with two M4 screws. Wire it through a toggle switch to the DC supply as for our 1924 router.

Material untuk langkah ini:

Filamen PETGFilamen PETG1 buah
Motor listrikMotor listrik1 buah
Adaptor kolet poros motorAdaptor kolet poros motor1 buah
Sekrup Kepala SoketSekrup Kepala Soket2 buah
Sakelar tuasSakelar tuas1 buah
Kawat hubungKawat hubung1 buah
Selongsong bakarSelongsong bakar1 buah

Alat yang dibutuhkan:

Pencetak 3D filamen (FDM)Pencetak 3D filamen (FDM)
Sumber daya arus searahSumber daya arus searah
Solder ListrikSolder Listrik
Set kunci LSet kunci L
5

The screw leg and knob

Press an M10 nut into the trap under the boss. Cut 100 mm of M10 threaded rod, round its lower end with a file so it slides on the table, and screw it up through the nut. Turn a hardwood knob 25, bore it, and glue it on the rod's top with a nut locked under it.

Material untuk langkah ini:

Mur Segi EnamMur Segi Enam2 buah
Batang berulirBatang berulir1 buah
Papan Kayu KerasPapan Kayu Keras1 buah
Lem KayuLem Kayu1 buah

Alat yang dibutuhkan:

Gergaji BesiGergaji Besi
Set KikirSet Kikir
Mesin bubut kayuMesin bubut kayu
Bor Tanpa KabelBor Tanpa Kabel
Set Mata BorSet Mata Bor
Kunci InggrisKunci Inggris
6

Rout

Clamp the work down on the table between two strips. Fit a bit and stand the router on the table so its legs are beside the work and the bit is over it. Turn the knob until the bit just clears the work, switch on, and turn it down a little while moving the router over the area to be cut, one hand on arm 11 and the other on the knob.

Alat yang dibutuhkan:

Set mata mesin profilSet mata mesin profil
Papan Kayu KerasPapan Kayu Keras
Klem batangKlem batang
Jangka Sorong Digital 6 InciJangka Sorong Digital 6 Inci
Kacamata pengamanKacamata pengaman
7

Troubleshooting

Three-legged router troubleshooting.

Flow

Loading...
8

History and honest limits

**Homer E. Willard** and **Frederick S. Young** of Toledo, Ohio, US 2,146,458, dated 7 February 1939, filed 11 December 1935. They claimed "a portable router comprising a T-shaped frame having a semi-circular recess in the stem of the T, a bit-operating motor mounted in said recess and a leg projecting in the same direction as the bit from each of the ends of the frame", one leg "screw-threaded through the arm and terminating above the arm in an operating knob". Their work was an electrotype clamped on the table; their motor ran on mains. Ours is a small DC motor in a printed frame. They give no sizes; every size here is ours.

Bahan

11

Alat yang Diperlukan

15

Berkas desain

1

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...