Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI

Jack-o'-Lantern Light: a Dry Cell in a Tin Clip and a Hinged Bulb Holder Instead of a Candle (Root, 1953)
Howard S. Root of Spokane received US 2,631,224, dated 10 March 1953, for a safe light for jack-o'-lanterns: "The most common device is an ordinary candle. That, however, is very dangerous." A springy tin clip holds a dry cell; a bulb screwed into a hinged tin support rests on the top of the cell, and the clip itself carries the current back from the bottom. A wire handle through the lid lifts the bulb to switch it off.
We bend it from tinplate and fit it in a carved pumpkin. All sizes are ours.
Pemula
About 2 hours
Instruksi
1
1
Bracket blank
Bracket blank
Memuat notebook Jupyter…
2
2
Read US 2,631,224
Read US 2,631,224
"I provide an operating means for the light bulb support 18 of such a nature that the child can turn the light on and off at will, yet if the entire toy is carried by the operating handle, no harm is done to the device."
3
3
Bend the cell clip
Bend the cell clip
Cut the tinplate strip from the notebook. Bend it into a U round the cell, his container 10: the bottom is the cross bar 10c, the sides are legs 10a and 10b. Curve the legs a little across their width so the cell cannot slide out sideways, and snip and press in a small tongue on each leg (his 15) to grip it. Snip two pointed fingers at the bottom (his 13).
Material untuk langkah ini:
Lembaran pelat timah1 buahAlat yang dibutuhkan:
Gunting seng
Tang Berujung Rata4
4
Make the bulb support
Make the bulb support
Cut a tin plate a little longer than the cell is wide, his support 18. Punch a hole in the middle just big enough for the bulb's screw base to screw into (his threaded aperture 19; ours). Bend two small ears at the top of leg 10a (his 21) and roll the support's end round a wire pin (22) between them, so it hinges.
Material untuk langkah ini:
Lembaran pelat timah1 buah
Kawat baja pegas1 buahAlat yang dibutuhkan:
Gunting seng
Penitik
Tang berujung bulat
Tang Berujung Rata5
5
Fit the spring and handle
Fit the spring and handle
Wind a few turns of spring wire on the hinge pin, one end hooked over the top of leg 10a and the other over the support, so it presses the support down (his spring 25). Bend a wire handle (his 20) long enough to come out of the top opening; pivot its lower end in a turned-over tab on leg 10b (26) and bend a short arm (27) under the free end of the support, so raising the handle lifts the bulb.
Material untuk langkah ini:
Kawat baja pegas1 buahAlat yang dibutuhkan:
Tang berujung bulat
Tang Berujung Rata
Tang potong6
6
Put in the cell and bulb
Put in the cell and bulb
Seat the cell with its centre terminal down on the cross bar, put a tin band (his 16) round the legs if they are loose, and screw the bulb into the support. Let the support down: the bulb's end terminal should touch the top of the cell and light, the current returning through the support, the hinge and the clip.
Material untuk langkah ini:
Baterai kering1 buah
Bohlam senter1 buah
Lembaran pelat timah1 buahAlat yang dibutuhkan:
Gunting seng
Tang Berujung Rata7
7
Fit it in the pumpkin
Fit it in the pumpkin
Carve the pumpkin's face and cut the top opening (ours; his toys are hollow figures). Push the clip's fingers through the bottom of the pumpkin, put a washer over them outside, and bend them over it (his washer 8), so the light stands in the middle. Pass the handle up through the top opening.
Material untuk langkah ini:
Labu kuning1 buah
Ring Rata1 buahAlat yang dibutuhkan:
Pisau Kerajinan
Tang Berujung Rata8
8
Use it
Use it
Lower the handle and the bulb lights; raise it and the light goes off. To change the cell, lift the support and take the cell out.
9
9
Troubleshooting
Troubleshooting
Jack-o'-lantern light troubleshooting.
Flow
Loading...
10
10
History and honest limits
History and honest limits
**Howard S. Root** of Spokane, Washington, US 2,631,224, dated 10 March 1953, filed 21 December 1948. He claimed "an illuminated figure toy comprising a hollow body having an opening in the top thereof", a conductive container for a dry cell, a hinged conductive bulb support, and spring means pressing the bulb's end terminal against the cell. He also shows other hinges, a magnet latch and a side handle (Figs. 6-13), not built here. He gives no sizes or materials: the tinplate, all sizes, the pumpkin and the cell and bulb are ours.
Bahan
6- 3 buahPlaceholder
- 2 buahPlaceholder
- 1 buahPlaceholder
- 1 buahPlaceholder
- 1 buahPlaceholder
- 1 buahPlaceholder
Cetak biru ini membuat
Blueprint terkait
Blueprint ini berbagi pengetahuan — teknik, bahan, atau prinsip
CC0 Domain Publik
Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.
Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.


