Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Bulb Pipette Blown at the Lamp: a Closed Tube Drawn, Bulbed, Pierced and Joined to Two Stems (Soward, 1886)
Bubbles

Dibuat oleh

Bubbles

14. November 2026IT
4
0
0
0
0

Bulb Pipette Blown at the Lamp: a Closed Tube Drawn, Bulbed, Pierced and Joined to Two Stems (Soward, 1886)

Alfred Soward's lampwork bulb pipette from Amateur Work (1886), made like his thistle funnel: a 3/8 in. bore tube closed and drawn down onto a 1/8 in. stem, blown into a bulb, a thin second bulb blown and broken off the far side to leave a short neck, and a second stem drawn to a fine capillary tip joined on.
Lanjutan
An hour once the basic operations are mastered

Instruksi

1

Read Soward

"To make a pipette the process is very similar." (to the thistle funnel)
2

Prepare the tubes

Take glass tube of about 1/8 in. (3 mm) bore for the stems and about 3/8 in. (10 mm) bore for the bulb. Close the wide tube at one end in the form of his fig. 41 A, then soften it about an inch from the end and draw it down to the small tube's diameter.

Material untuk langkah ini:

Tabung kacaTabung kaca1 buah

Alat yang dibutuhkan:

Pembakar BunsenPembakar Bunsen
Pipa tiup peniup kacaPipa tiup peniup kaca
3

Join the first stem

Cut the drawn, flask-shaped piece off with a file and fuse it to a length of the narrow tube: soften both ends, press them together, pull gently to reduce the thickened joint, and blow a gentle stream of air in.

Material untuk langkah ini:

Tabung kacaTabung kaca1 buah

Alat yang dibutuhkan:

Kikir (Kikir Tangan)Kikir (Kikir Tangan)
Pembakar BunsenPembakar Bunsen
Pipa tiup peniup kacaPipa tiup peniup kaca
4

Blow the bulb

Soften the flask part and blow it into a bulb through the stem.

Alat yang dibutuhkan:

Pembakar BunsenPembakar Bunsen
Pipa tiup peniup kacaPipa tiup peniup kaca
5

Open the far end

Play the flame on the point opposite the stem (A in fig. 41) and blow a very thin second bulb with a strong blast. Break it away: it leaves a small projecting tube (B).

Alat yang dibutuhkan:

Pembakar BunsenPembakar Bunsen
Pipa tiup peniup kacaPipa tiup peniup kaca
6

Draw and join the tip

Draw a second piece of narrow tube to a capillary end: thicken it in the flame, pull the hands apart, cut with a file and hold the cut end a moment in the flame. Join this stem to the projecting tube as before.

Material untuk langkah ini:

Tabung kacaTabung kaca1 buah

Alat yang dibutuhkan:

Kikir (Kikir Tangan)Kikir (Kikir Tangan)
Pembakar BunsenPembakar Bunsen
Pipa tiup peniup kacaPipa tiup peniup kaca
7

Troubleshooting

Pipette troubleshooting.

Flow

Loading...
8

History and honest limits

From Alfred W. Soward, "Glass-Blowing for Amateurs" IV, **Amateur Work, Illustrated**, vol. V (1886), pp. 173-176, figs. 39-41 (checked on the archive.org scan amateurworkillus05lond). He gives no volume or graduation: calibrate it by weighing water if you need one (see the graduated-pipette blueprint). Metric figures are ours.

Bahan

1

Alat yang Diperlukan

3

Cetak biru ini membuat

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...