Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Cork Borer from Brass Tube: Edge Filed Like Two Gouges Back to Back, Steel Wire Handle (Soward, Amateur Work, 1881)
Forge

Dibuat oleh

Forge

15. November 2026NO
4
0
0
0
0

Cork Borer from Brass Tube: Edge Filed Like Two Gouges Back to Back, Steel Wire Handle (Soward, Amateur Work, 1881)

Alfred Soward's laboratory cork-borer from Amateur Work (1881): about 4 in. of brass tube the size of the hole, one end filed on the outside to a ring-shaped cutting edge, a brass flange on the other end to strengthen it, and a steel wire pushed through a cross hole as a handle. Turned like a gimlet, it cuts a clean, centred hole for a glass tube.
Pemula
An hour

Instruksi

1

Read Soward

"This latter instrument is simply a piece of brass tube about 4 in. long, and of a diameter suited to the hole required."
2

Cut the tube

Cut about 4 in. (100 mm) of brass tube whose outside diameter matches the hole you need (he takes 3/8 in., about 10 mm, for a glass tube). Square both ends.

Material untuk langkah ini:

Tabung kuninganTabung kuningan1 buah

Alat yang dibutuhkan:

Ragum MejaRagum Meja
Gergaji BesiGergaji Besi
Kikir (Kikir Tangan)Kikir (Kikir Tangan)
3

File the cutting edge

File one end on the outside only, all round, to a thin cutting edge: like two gouges put together with their hollow sides facing (B in his fig. 7). Leave the bore untouched.

Alat yang dibutuhkan:

Ragum MejaRagum Meja
Kikir (Kikir Tangan)Kikir (Kikir Tangan)
Kikir jarumKikir jarum
4

Fit the flange

Fit a small brass ring or flange round the other end to strengthen it (D in fig. 7). Ours: cut it from brass sheet and soft-solder it on.

Material untuk langkah ini:

Lembaran KuninganLembaran Kuningan1 buah
Kawat Timah SolderKawat Timah Solder1 buah
FluksFluks1 buah

Alat yang dibutuhkan:

Gunting sengGunting seng
Mesin Bor DudukMesin Bor Duduk
Set Mata BorSet Mata Bor
SolderSolder
5

Cross hole and handle

Below the flange, drill a hole straight across the tube for a piece of steel wire. Push the wire through so it stands at right angles to the tube as a handle (C in fig. 7, drawn with a head on one end).

Material untuk langkah ini:

Kawat bajaKawat baja1 buah

Alat yang dibutuhkan:

Mesin Bor DudukMesin Bor Duduk
Set Mata BorSet Mata Bor
Kikir (Kikir Tangan)Kikir (Kikir Tangan)
6

Troubleshooting

Cork borer troubleshooting.

Flow

Loading...
7

History and honest limits

From Alfred W. Soward, "Filters: Their Construction and Maintenance" I, **Amateur Work, Illustrated**, vol. I (1881), pp. 131-133 and fig. 7 (checked on the archive.org scan amateurworkillus11881lond). To use it, hold the cork's small end against a wall or the bench edge, press on the centre of the large end and turn like a gimlet, giving the cork a quarter turn left after each quarter turn of the borer right. A bought set of four then cost 1s. He does not say how the flange is fixed: soft solder, the metric figures and the tools are ours.

Bahan

5

Alat yang Diperlukan

8

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...