Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Stovetop Kettle: a Square Copper Kettle (Hasluck, 1907)
Forge

Dibuat oleh

Forge

4. November 2026NO
10
0
0
0
0

Stovetop Kettle: a Square Copper Kettle (Hasluck, 1907)

A tinsmith's square kettle in sheet copper, 9 x 9 in and 3 5/8 in deep: a box body with folded corner seams, a hollowed top pened on, a brazed and bent spout, a small cover, and a wooden handle on brass uprights. Hasluck prefers copper; tinplate also works and is a separate route. Source: Paul N. Hasluck, Tinplate Work (1907), pp. 91-98. Unknown: copper gauge, solder. Picture: Figs. 188-189 of the book.
Lanjutan
Unknown

Instruksi

1

Cut the patterns

For a body 9 x 9 x 3 5/8 in, cut two ends 9 1/2 x 4 in and two sides 9 1/4 x 4 in, notched for box seams at the corners (Figs. 190-191), with allowances to fold at top and bottom. Punch the spout hole in the front. Cut the bottom 9 1/2 in square, notched for a 1/4 in edge. Set out the top as a 10 1/2 in square with curved allowances for hollowing and a 4 in circle for the cover hole (Fig. 193); set out the spout from the elevation (Fig. 192), the cover and its cone-shaped rim (Figs. 194-195).

Material untuk langkah ini:

Lembaran TembagaLembaran Tembaga1 body, bottom, top, spout, cover

Alat yang dibutuhkan:

Jangka tusukJangka tusuk
PenggoresPenggores
Gunting sengGunting seng
2

Braze and shape the spout

Thin the long edges by hammering. Set in the throat with a stretching hammer on a beak iron, bend the spout round until the edges overlap, bind it with wire, lay spelter and borax along the inside of the seam and braze it; then close and braze the under seam. Fill it with lead and bend the neck with a round-faced hammer on the hollowing block; file off spare spelter and smooth it. Run out the lead, throw off a seating round the large end, trim the top with snips and tin the inside.

Material untuk langkah ini:

Logam tidak diketahuiLogam tidak diketahui1 spelter
TimahTimah1 tinning

Alat yang dibutuhkan:

Palu perataPalu perata
PasakPasak
Kawat besiKawat besi
Serbuk boraksSerbuk boraks
Obor patri kerasObor patri keras
TimbalTimbal
Serok berlubangSerok berlubang
Balok Kayu KerasBalok Kayu Keras
Kikir LogamKikir Logam
Gunting sengGunting seng
3

Fold and seam the body

Fold the top edges square, the front and back outwards and the sides likewise; fold the bottom edges right over inwards to take the bottom (Fig. 188). Hook each side's end over the front's and work the corner seam on a straight-edged tool (Figs. 198-199). Turn up the bottom's 1/4 in edge, push it edge-down into the bottom folds, and solder the bottom and seams.

Material untuk langkah ini:

Patri timah-timbalPatri timah-timbal1 buah

Alat yang dibutuhkan:

Palu KayuPalu Kayu
PasakPasak
Solder ListrikSolder Listrik
FluksFluks
4

Hollow the top and make the cover

Hollow the top on the block: sink the four sides a little, hollow the corners with a bullet-faced hammer, flatten each side along the block edge, even the shoulder and smooth it all over. Pare the edges, mark the flange with an edging machine, set it down square with a hatchet stake and mallet, and take up an edge to fit over the body. Cut the cover hole with circular snips and fit a narrow wired rim, worked over inside. Make the cover: solder its cone rim to fit the wired rim, throw off a flange, hollow the cover disc and seam it on, and fix the knob.

Material untuk langkah ini:

Kawat besiKawat besi1 rim
Patri timah-timbalPatri timah-timbal1 buah
Logam tidak diketahuiLogam tidak diketahui1 cover knob

Alat yang dibutuhkan:

Palu perataPalu perata
Balok Kayu KerasBalok Kayu Keras
PasakPasak
Palu KayuPalu Kayu
Gunting sengGunting seng
Solder ListrikSolder Listrik
FluksFluks
5

Handle, top and spout

Cut two handle uprights from stout brass or copper band (Fig. 196), drill them for rivets and for the spindle that carries the wooden handle, and bend them to shape. Rivet them to the top and solder over the rivet heads inside. Pene the top down onto the body and solder along each edge. Push the spout through its hole from inside until its large end butts against the front, and solder it strongly from inside.

Material untuk langkah ini:

Lembaran KuninganLembaran Kuningan1 handle uprights
Batang KuninganBatang Kuningan1 spindle
GagangGagang1 wood
Paku keling tembagaPaku keling tembaga1 number not given
Patri timah-timbalPatri timah-timbal1 buah

Alat yang dibutuhkan:

Bor tanganBor tangan
Palu kelingPalu keling
Palu KayuPalu Kayu
Solder ListrikSolder Listrik
FluksFluks

Bahan

9

Alat yang Diperlukan

17

Cetak biru ini membuat

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...