Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Garden Hand Plow From Scrap: Wheelbarrow Wheel, Ripped Spruce Handles and a Shovel-Blade Moldboard (Boy Mechanic, 1919)
Forge

Dibuat oleh

Forge

13. November 2026NO
8
0
0
0
0

Garden Hand Plow From Scrap: Wheelbarrow Wheel, Ripped Spruce Handles and a Shovel-Blade Moldboard (Boy Mechanic, 1919)

T. T. Sturgeon's hand plow from The Boy Mechanic, Book 3 (1919), "worth about $5 at an outlay of 25 cents": a 16 in wheelbarrow wheel, handles ripped from one spruce strip, iron-strap braces, an adjustable vertical strap, and a moldboard and share cut from an old shovel blade to his grid pattern.
Menengah
About 1 day

Instruksi

1

His cut list in centimetres

Memuat notebook Jupyter…
2

Read The Boy Mechanic, Book 3

"The labor of spading a garden of even moderate size is sufficient to warrant the person who undertakes the job in making a hand plow like that shown in the illustration."
3

Make the handles

Mark both handles on a 7/8 by 4 in spruce strip 5 ft long, one curved grip at each end on opposite edges. Cut the curves with a keyhole saw, then rip the board into the two handles; smooth them and trim the grips with a sharp knife. Cut a section of broomstick for the upper brace.

Material untuk langkah ini:

Papan Kayu KerasPapan Kayu Keras1 buah
SapuSapu1 buah

Alat yang dibutuhkan:

Gergaji CopingGergaji Coping
Gergaji belahGergaji belah
Pisau kulitPisau kulit
PensilPensil
4

Make the iron parts

Lower brace: iron 1/4 by 1-1/4 by 12 in, drilled for 1/4 in bolts, bent at right angles 1-1/2 in from each end, with a 1/4 in hole at the middle. Vertical support: 1/4 by 1-1/4 by 18 in, four 1/4 in adjusting holes 1 in apart at the top, three 1/4 in holes at the bottom for the moldboard, and a 5/16 in hole at the 7-1/2 in mark. Two braces 14 in long of 1/4 by 1-1/4 in, a 3/8 in hole at the front of each for the 3/8 by 10 in axle bolt and a 5/16 in hole at the other end, each 1 in from the end. Landside: 1/8 by 3/4 by 12 in.

Material untuk langkah ini:

Besi Strip Baja LunakBesi Strip Baja Lunak3 buah

Alat yang dibutuhkan:

Gergaji BesiGergaji Besi
Bor tanganBor tangan
Ragum MejaRagum Meja
PaluPalu
Kikir (Kikir Tangan)Kikir (Kikir Tangan)
Meteran GulungMeteran Gulung
5

Cut the moldboard

Draw his moldboard (Fig. 4) on cardboard ruled in 1 in squares, tracing the outline square by square, and mark the bolt holes. Trace it on an old shovel blade, using the thickest part for the point of the share. Cut it out, smooth the edges and sharpen the cutting edge. Drill for 1/4 in bolts to the vertical strap and 3/16 in bolts to the landside.

Material untuk langkah ini:

SekopSekop1 buah
Lembar mal kartonLembar mal karton1 buah

Alat yang dibutuhkan:

PensilPensil
Gergaji BesiGergaji Besi
Gerinda sudutGerinda sudut
Kikir (Kikir Tangan)Kikir (Kikir Tangan)
Bor tanganBor tangan
6

Shape and assemble

Curve the moldboard and fit it to the supports as in Figs. 1-3. Bend the 12 in landside strip under the moldboard and bolt it on. Assemble on the 16 in wheel and 3/8 in axle bolt, with wheel and landside in line (Fig. 2) and the landside's rear edge raised slightly (Fig. 3); set the vertical strap's height for the operator in its adjusting holes. Paint the plow and oil the smoothed cutting parts.

Material untuk langkah ini:

Roda gerobak sorongRoda gerobak sorong1 buah
Baut kepala bulat leher persegiBaut kepala bulat leher persegi6 buah
Mur Segi EnamMur Segi Enam6 buah
Ring RataRing Rata6 buah
Cat minyakCat minyak1 buah
Oli MesinOli Mesin1 buah

Alat yang dibutuhkan:

Ragum MejaRagum Meja
PaluPalu
Kuas lebarKuas lebar
7

Troubleshooting

Garden plow troubleshooting.

Flow

Loading...
8

History and honest limits

From "Garden Plow Made of Pick-Up Material" by T. T. Sturgeon, in **The Boy Mechanic, Book 3**, Popular Mechanics, 1919 (Project Gutenberg 71856; checked on the archive.org scan boymechanic0003unse, pp. 227-228). The moldboard shape is his Fig. 4 grid. The keyhole saw is a coping saw here; the tools and metric figures are ours.

Bahan

11

Alat yang Diperlukan

12
  • Placeholder
  • Placeholder
  • Placeholder
  • 1 vendor sell this, none ship to you yet
    Placeholder
  • Placeholder
  • Placeholder
  • Placeholder
  • Placeholder
  • Placeholder
  • 1 vendor sell this, none ship to you yet
    Placeholder
  • 1 vendor sell this, none ship to you yet
    Placeholder
  • Placeholder

Cetak biru ini membuat

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...