Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Skis: Ash or Hickory Planks Shaped to an 8 ft Pattern, Steam-Bent Tips and a Running Groove (Boy Mechanic, 1919)
Woody

Dibuat oleh

Woody

13. November 2026NO
5
0
0
0
0

Skis: Ash or Hickory Planks Shaped to an 8 ft Pattern, Steam-Bent Tips and a Running Groove (Boy Mechanic, 1919)

Stillman Taylor's skis from The Boy Mechanic, Book 3 (1919): "far easier than snowshoe construction, since each runner is made from a single piece of plank". Ash or hickory is cut to his 8 ft pattern, thinned from the top only, the tips steamed to a 6 in bend, a centre groove cut, and the skis oiled and waxed.
Menengah
About 1 week

Instruksi

1

Fig. 5 in centimetres, and the wax

Memuat notebook Jupyter…
2

Read The Boy Mechanic, Book 3

"Either hickory or ash will give satisfaction, because both are heavy woods, as well as strong and flexible." For a man of good height, 7 to 8 ft is the right length.
3

Get and choose the wood

Get two ash or hickory planks about 9 ft long and 2 in thick, from the outside of the lower trunk, with the grain running as in his Fig. 6, A/D (in ash choose open, widely spaced grain). Or split a sound, straight tree about 10 in across and clear of knots for 10 ft: axe a straight groove about 1 in deep along each side and drive small wood wedges along it; hew only enough off the outside to make the flat running surface.

Material untuk langkah ini:

Papan Kayu KerasPapan Kayu Keras2 buah

Alat yang dibutuhkan:

Gergaji TanganGergaji Tangan
Meteran GulungMeteran Gulung
4

Lay out and saw

Make a paper pattern from his Fig. 5 (8 ft ski): 3-3/8 in wide at the heel, 3-1/8 in at the foot, 4 in at the bend, rounding to the toe. Trace it on the plank and saw out; on green wood make the width about 1/4 in greater for shrinkage.

Material untuk langkah ini:

Papan Kayu KerasPapan Kayu Keras1 buah

Alat yang dibutuhkan:

PensilPensil
Gergaji TanganGergaji Tangan
Meteran GulungMeteran Gulung
5

Plane to thickness

Plane the running surface perfectly smooth, grain straight from point to heel. Work the thickness down from the top side only, never the bottom: about 1/2 in at the heel, 3/4 in at the foot and 1/2 in at the bend.

Alat yang dibutuhkan:

Ketam tanganKetam tangan
Ketam lengkungKetam lengkung
6

Steam the tip

Lay the ski over a wash boiler of boiling water and soak the tip by mopping it with the water on a cloth tied to a stick. Bend gradually over many treatments to a good 6 in bend (it finishes near 5 in, as the wood straightens a little as it dries). Hold it in a rough frame over a short log, or lash or cleat the tips to the bench, as in his Fig. 7. The arch under the foot is easily put in, and easily straightened when cold if overdone.

Alat yang dibutuhkan:

Panci BesarPanci Besar
Alat pelAlat pel
Klem batangKlem batang
7

Binding hole, balance and groove

Put in the hole for the foot binding. If the wood was left long, trim the heel so the ski balances when lifted by the toe straps (he sees no advantage in weighting a light heel with lead). Cut a groove in the exact centre of the running surface, about 1/8 in deep and 3/8 to 1/2 in wide, from the heel to the start of the bend, with a grooving plane or a small gouge.

Material untuk langkah ini:

Tali KulitTali Kulit2 buah

Alat yang dibutuhkan:

Bor tanganBor tangan
Pahat kayuPahat kayu
Pahat LengkungPahat Lengkung
Gergaji TanganGergaji Tangan
8

Finish and wax

Sandpaper top and bottom and rub down with linseed oil with a little paraffin or beeswax in it; oil and wax the running surface (spar varnish on the tops if you want gloss). For a hard wax, melt 10 oz of beeswax with 5 oz of rosin, stir in 1 oz of turpentine and pour into small boxes. Rub it on and go over it with a hot flatiron; too much wax makes climbing hard.

Material untuk langkah ini:

AmplasAmplas1 buah
Minyak Biji RamiMinyak Biji Rami1 buah
Lilin parafinLilin parafin1 buah
Malam LebahMalam Lebah1 buah
Damar pinusDamar pinus1 buah
TerpentinTerpentin1 buah

Alat yang dibutuhkan:

Panci BesarPanci Besar
Setrika besiSetrika besi
Kuas lebarKuas lebar
9

Troubleshooting

Ski troubleshooting.

Flow

Loading...
10

History and honest limits

From "How to Make Skis" by Stillman Taylor, in **The Boy Mechanic, Book 3**, Popular Mechanics, 1919 (Project Gutenberg 71856; checked on the archive.org scan boymechanic0003unse, pp. 27-30). His text gives the groove as 3/8 to 1/2 in wide; Fig. 5 shows 3/8 in. He does not describe the binding. The tools and metric figures are ours.

Bahan

8
  • Placeholder
  • Placeholder
  • 1 buah
    Placeholder
  • Placeholder
  • Placeholder
  • Placeholder
  • Placeholder
  • 1 buah
    Placeholder

Alat yang Diperlukan

13
  • Placeholder
  • 1 vendor sell this, none ship to you yet
    Placeholder
  • 1 vendor sell this, none ship to you yet
    Placeholder
  • Placeholder
  • Placeholder
  • Placeholder
  • Placeholder
  • Placeholder
  • Placeholder
  • Placeholder
  • Placeholder
  • Placeholder
  • Placeholder

Cetak biru ini membuat

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...