Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Canoe Sailing Rig: Bamboo Mast, 9 ft Lateen Sail, Clamp-In Mast Thwart and Leeboards (Boy Mechanic, 1919)
Woody

Dibuat oleh

Woody

13. November 2026NO
6
0
0
0
0

Canoe Sailing Rig: Bamboo Mast, 9 ft Lateen Sail, Clamp-In Mast Thwart and Leeboards (Boy Mechanic, 1919)

Stillman Taylor's sailing outfit for a 16 ft open canoe from The Boy Mechanic, Book 3 (1919): a 6 ft 10 in bamboo mast, a 9 ft lateen sail of cotton sheeting on two bamboo spars, a mast thwart and leeboard thwart that clamp to the gunwales with brass lantern-board hooks, and leeboards set by thumb nuts. Steer with the paddle.
Menengah
A few days

Instruksi

1

Rig sizes and sail area

Memuat notebook Jupyter…
2

Read The Boy Mechanic, Book 3

"The lateen rig is best for an open canoe, because a shorter mast is required for the same sail area ... It is not safe to rig a canoe too heavily, and the rig described has been found to be well proportioned."
3

Make the mast

Cut bamboo 1-1/2 in across to 6 ft 10 in (carpet dealers' rolling bamboo of 1-1/2 to 2 in serves). Whittle a tapered wooden plug about 3 in long to wedge firmly in the top without splitting the cane, bore a small hole through the cane 2 in from the top, and fix a screw eye into the plug for the halyard. Drive small brads through the cane into the plug, and fit a brass ferrule over the end.

Material untuk langkah ini:

Bilah bambu panjangBilah bambu panjang1 buah
Papan Kayu KerasPapan Kayu Keras1 buah
Sekrup mataSekrup mata1 buah
PakuPaku1 buah
Cincin logamCincin logam1 buah

Alat yang dibutuhkan:

Gergaji TanganGergaji Tangan
Pisau kulitPisau kulit
Bor tanganBor tangan
PaluPalu
4

Make the spars

Use two bamboo fishing rods, 1 in at the butt and 10 ft long, as gaff and boom. Fix a 1-1/2 in screw eye with a 1/2 in eye at the end of each and join the spar ends with a 1-1/2 in brass split ring and a 1-3/4 in brass S hook. Fasten the 2 in brass boom jaw on the boom with its open end 18 in from the boom's forward end.

Material untuk langkah ini:

Batang bambuBatang bambu2 buah
Sekrup mataSekrup mata2 buah
Ring belah (gantungan kunci)Ring belah (gantungan kunci)1 buah
Kait SKait S1 buah
Rahang boomRahang boom1 buah
Sekrup kayuSekrup kayu1 buah

Alat yang dibutuhkan:

Bor tanganBor tangan
Obeng pipihObeng pipih
Meteran GulungMeteran Gulung
5

Sew the sail

Lay the spars on the cloth and pencil a triangle 9 ft on each side. Sew the widths of 1 yd unbleached cotton sheeting together, lapped about 1/2 in and stitched close to both edges, preferably on a machine. Sew bights (folds) 1/2 in wide, 6 in apart, parallel with the leech. Reinforce the corners with segments of cloth. Along the edges lashed to the spars fold and sew 1 in hems, running a 1/2 in tape into the leech hem; fasten the tape to the spar at each end to take up stretch and stop a flapping leech.

Material untuk langkah ini:

Kain KatunKain Katun8 yard
Benang jahitBenang jahit1 buah
Pita kepar katunPita kepar katun1 buah

Alat yang dibutuhkan:

Mesin jahitMesin jahit
GuntingGunting
PensilPensil
Meteran GulungMeteran Gulung
6

Make the thwarts and mast step

Mast thwart: two cedar or pine boards 28 by 10 by 3/8 in and a piece 27-1/2 by 3-1/2 by 3/4 in, made as in the plate with a hole in the centre for the mast and a brass lantern-board hook at each end to clamp it to the gunwales. Mast step: a block 5 by 2-1/2 by 1 in, shaped neatly, fixed to the grating (or the ribs). Leeboard thwart: cedar or white pine 5 ft by 4 by 7/8 in, with short upright ends set at an angle to the canoe's curve so it wedges in just aft of the mast; groove the ends to the thwart and screw them on. He gives no leeboard sizes; bolt a leeboard to each end with a 3 in by 5/16 in brass bolt, washer and thumb nut so its angle can be set.

Material untuk langkah ini:

Papan kayu cedarPapan kayu cedar4 buah
Kait papan lenteraKait papan lentera4 buah
Baut komporBaut kompor2 buah
Ring RataRing Rata2 buah
Mur sayapMur sayap2 buah
Sekrup kayuSekrup kayu1 buah

Alat yang dibutuhkan:

Gergaji TanganGergaji Tangan
Gergaji CopingGergaji Coping
Ketam tanganKetam tangan
Pahat kayuPahat kayu
Bor engkol dan mata borBor engkol dan mata bor
Obeng pipihObeng pipih
7

Finish and rig

Smooth all woodwork with sharp tools, sandpaper lightly, and give three coats of spar varnish. Lash the sail to the spars, run the 1/4 in cotton-rope halyard through the screw eye at the masthead until the gaff is close to the top, and find the balance by tying the halyard at different points along the gaff. Run the halyard under the forward thwart to the stern, never tied to it, and loop the main sheet round a thwart and hold it, never made fast.

Material untuk langkah ini:

AmplasAmplas1 buah
Pernis tiang kapalPernis tiang kapal1 buah
Tambang kapasTambang kapas1 buah

Alat yang dibutuhkan:

Kuas lebarKuas lebar
GuntingGunting
8

Sailing safely

Canoe sailing.

Flow

Loading...
9

History and honest limits

From "How to Build a Canoe, Part II" by Stillman Taylor, in **The Boy Mechanic, Book 3**, Popular Mechanics, 1919 (Project Gutenberg 71856; checked on the archive.org scan boymechanic0003unse, pp. 86-88). He gives no leeboard sizes (they vary with the canoe); the list calls the leeboard bolts brass stove bolts with thumb nuts and the text carriage bolts with wing nuts. Cedar for the leeboards, the sail area and the metric figures are ours.

Bahan

21

Alat yang Diperlukan

14
  • Placeholder
  • Placeholder
  • Placeholder
  • Placeholder
  • Placeholder
  • 1 vendor sell this, none ship to you yet
    Placeholder
  • Placeholder
  • Placeholder
  • 1 vendor sell this, none ship to you yet
    Placeholder
  • Placeholder
  • Placeholder
  • Placeholder
  • Placeholder
  • Placeholder

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...