Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Tube-Track Pedal Saw Table: Any Portable Saw Clamped Upside Down on a Carriage Rolling Inside Slotted Tubes (Tomlinson & Bearden, 1931)
Forge

Dibuat oleh

Forge

13. November 2026NO
6
0
0
0
0

Tube-Track Pedal Saw Table: Any Portable Saw Clamped Upside Down on a Carriage Rolling Inside Slotted Tubes (Tomlinson & Bearden, 1931)

William A. Tomlinson and Howell B. Bearden of Phoenix, Arizona, received US 1,813,783, dated 7 July 1931, for a table that turns any portable power saw into a table saw. The saw is clamped upside down on a carriage, its blade through the slot of a top hinged at the rear. The carriage rolls on ball-bearing rollers inside two steel tubes slotted along their undersides. A pedal pushes it forward through the work, leaving both hands free, and a spring brings it back. With the pedal left alone it works as a fixed saw, and the saw unbolts for hand use. The patent gives no sizes; every size here is ours.
Lanjutan
About 4 days

Instruksi

1

Pedal, link and travel

Memuat notebook Jupyter…
2

Read US 1,813,783

"By using the pedal in the manner above set forth both hands of the operator will be free for manipulating the work, which is especially desirable when pattern work is to be sawed."
3

Angle-iron frame

Bolt a frame of steel angle 900 x 500 mm, 850 high: four corner legs 1, side and end bars 2, 3 halfway up and 4, 5 at the top, flat-bar diagonal braces 6 at the top corners, a cross bar 7 between the rear legs above the middle bars, and a cross bar 8 between the front legs at the bottom. Drill a vertical row of 9 mm holes 13, 25 mm apart, near the top of each leg, for the track hangers.

Material untuk langkah ini:

Besi siku baja lunakBesi siku baja lunak6 buah
Besi Strip Baja LunakBesi Strip Baja Lunak1 buah
Aneka baut segi enamAneka baut segi enam40 buah
Mur Segi EnamMur Segi Enam40 buah
Ring RataRing Rata40 buah

Alat yang dibutuhkan:

Gergaji BesiGergaji Besi
Gerinda sudutGerinda sudut
Mesin Bor DudukMesin Bor Duduk
Set Mata BorSet Mata Bor
PenitikPenitik
Siku KombinasiSiku Kombinasi
Meteran GulungMeteran Gulung
Kunci InggrisKunci Inggris
Kacamata pengamanKacamata pengaman
4

Slotted tube tracks

Cut two 900 mm lengths of 42 mm steel tube 9, 10 and cut a 10 mm slot 14 along the underside of each, stopping 20 mm short of the ends; file the slot's edges smooth. Bolt a flat-bar hanger 11 to each end of each tube and hang the tubes along the frame's sides from the legs with bolts 12 through the row of holes, at the height that suits your saw. Put a short coil spring 39 in each end of each tube as a buffer.

Material untuk langkah ini:

Pipa bulat baja lunakPipa bulat baja lunak2 buah
Besi Strip Baja LunakBesi Strip Baja Lunak1 buah
Coil SpringCoil Spring4 buah
Aneka baut segi enamAneka baut segi enam8 buah
Mur Segi EnamMur Segi Enam8 buah

Alat yang dibutuhkan:

Gergaji BesiGergaji Besi
Gerinda sudutGerinda sudut
Set KikirSet Kikir
Ragum MejaRagum Meja
Mesin Bor DudukMesin Bor Duduk
Set Mata BorSet Mata Bor
Kunci InggrisKunci Inggris
Jangka Sorong Digital 6 InciJangka Sorong Digital 6 Inci
Kacamata pengamanKacamata pengaman
5

Carriage and rollers

Cut the carriage 30 from 5 mm steel plate, as wide as between the tubes. At each corner bolt an upright flat-bar standard 31 that reaches up through a tube's slot, and on its top a short bar 33 across inside the tube carrying a 22 mm ball bearing 32 at each end on an M8 bolt with a lock nut. Slide the rollers into the tubes from the ends, the standards hanging down through the slots, and bolt them to the carriage.

Material untuk langkah ini:

Pelat baja lunakPelat baja lunak1 buah
Besi Strip Baja LunakBesi Strip Baja Lunak1 buah
Bantalan PeluruBantalan Peluru8 buah
Aneka baut segi enamAneka baut segi enam16 buah
Mur Pengunci Sisipan NilonMur Pengunci Sisipan Nilon8 buah
Ring RataRing Rata16 buah

Alat yang dibutuhkan:

Gergaji BesiGergaji Besi
Gerinda sudutGerinda sudut
Mesin Bor DudukMesin Bor Duduk
Set Mata BorSet Mata Bor
Set KikirSet Kikir
Ragum MejaRagum Meja
Kunci InggrisKunci Inggris
6

Pedal and springs

Pivot a lever 21 of steel flat bar on the front bottom cross bar 8, with an arm 22 to the side carrying the pedal 20 and a brace 23 from arm to lever. Join the lever's top to the carriage's front with a flat-bar link 24. Hook a return spring 25a from the rear cross bar 7 to the lever partway up.

Material untuk langkah ini:

Besi Strip Baja LunakBesi Strip Baja Lunak2 buah
Batang bulat baja lunakBatang bulat baja lunak1 buah
Pegas tarikPegas tarik1 buah
Aneka baut segi enamAneka baut segi enam4 buah
Mur Pengunci Sisipan NilonMur Pengunci Sisipan Nilon4 buah

Alat yang dibutuhkan:

Gergaji BesiGergaji Besi
Mesin Bor DudukMesin Bor Duduk
Set Mata BorSet Mata Bor
Ragum MejaRagum Meja
Kunci InggrisKunci Inggris
7

Mount the saw and the top

Turn the circular saw upside down on the carriage and bolt it by its base plate with bolts and wing nuts, so it lifts off for hand use; his T-bolt 34 and hook bolts 36 gripped the saw's handles, which modern saws do not suit. Make the top 42 of plywood on a steel angle frame 44, slotted along the blade's path, and hinge its rear edge to the frame so it swings up to reach the saw. Fit a catch 47 to lock it down and a folding flat-bar brace 49 to prop it up.

Material untuk langkah ini:

Gergaji bundarGergaji bundar1 buah
Aneka baut segi enamAneka baut segi enam4 buah
Mur sayapMur sayap4 buah
Lembaran kayu lapisLembaran kayu lapis1 buah
Besi siku baja lunakBesi siku baja lunak1 buah
Engsel daunEngsel daun2 buah
Kancing kaitKancing kait1 buah
Besi Strip Baja LunakBesi Strip Baja Lunak1 buah
Sekrup kayuSekrup kayu16 buah

Alat yang dibutuhkan:

Gergaji Ukir ListrikGergaji Ukir Listrik
Bor Tanpa KabelBor Tanpa Kabel
Set Mata BorSet Mata Bor
Gergaji BesiGergaji Besi
Kunci InggrisKunci Inggris
Siku KombinasiSiku Kombinasi
8

Cut

Lock the top down. Set the saw's depth so the blade stands 10 mm above the board. Place the board on the top in front of the blade, start the saw and press the pedal: the carriage rolls the running blade through it while both hands hold the work. Let the pedal up and the spring returns it. For ripping, leave the carriage still and feed the board.

Alat yang dibutuhkan:

Kacamata pengamanKacamata pengaman
Pelindung telinga (penutup telinga, SNR 30 dB)Pelindung telinga (penutup telinga, SNR 30 dB)
9

Troubleshooting

Tube-track saw table troubleshooting.

Flow

Loading...
10

History and honest limits

**William A. Tomlinson** and **Howell B. Bearden** of Phoenix, Arizona, US 1,813,783, dated 7 July 1931, filed 5 December 1928. They claimed a top with a slot, "laterally spaced longitudinally extending tubular tracks" below it, "slotted longitudinally on their lower faces", and a saw carriage with upstanding roller-carrying hangers in the tracks, their shanks through the slots. Their saw is held by its handles; ours by its base plate. Their frame is angle iron, as ours. They give no sizes; every size here is ours.

Bahan

18

Alat yang Diperlukan

15

Cetak biru ini membuat

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...