Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Sliding-Table Saw That Switches Itself: A Hand Saw Under a Table on Balls, Turned On and Off by the Stroke (Tracy, 1941)
Forge

Dibuat oleh

Forge

13. November 2026NO
8
0
0
0
0

Sliding-Table Saw That Switches Itself: A Hand Saw Under a Table on Balls, Turned On and Off by the Stroke (Tracy, 1941)

Mearl V. Tracy of Sacramento received US 2,260,421, dated 28 October 1941, for a light table saw to take onto a building job. An ordinary electric hand saw hangs under a table that slides on steel balls in channels. The work is held against a fixed fence and the table carries the saw through it. A springy finger on the table trips a snap switch, starting the saw just before it reaches the work and stopping it as the table comes back. One fence on a graduated plate serves as rip fence and mitre gauge. The patent gives no sizes; every size here is ours, and our box is plywood where his is sheet metal.
Menengah
About 3 days

Instruksi

1

Where the switch must trip

Memuat notebook Jupyter…
2

Read US 2,260,421

"The finger 25 is so disposed as to engage trigger 24 and close the switch when the table is advanced and just before the saw reaches the work under which the table slides, and to reengage the trigger and open the switch as the table retracts and approaches a fully retracted position."
3

The box frame

Make an open-topped box of 18 mm plywood 900 mm long, 450 wide and 300 high, the end panels 2 standing 40 mm lower than the sides 1, glued and screwed. Bolt a steel channel section 5 along the inside top of each side, its open face inwards, as his channels on the beams 4.

Material untuk langkah ini:

Lembaran kayu lapisLembaran kayu lapis1 buah
Profil baja kanal UProfil baja kanal U2 buah
Aneka baut segi enamAneka baut segi enam8 buah
Mur Segi EnamMur Segi Enam8 buah
Sekrup kayuSekrup kayu30 buah
Lem KayuLem Kayu1 buah

Alat yang dibutuhkan:

Gergaji Ukir ListrikGergaji Ukir Listrik
Bor Tanpa KabelBor Tanpa Kabel
Set Mata BorSet Mata Bor
Klem batangKlem batang
Siku KombinasiSiku Kombinasi
Meteran GulungMeteran Gulung
Gergaji BesiGergaji Besi
Kunci InggrisKunci Inggris
4

The sliding table

Cut the table 6 from 18 mm plywood 600 x 400 mm with a saw slot 15 down its middle, and bolt a steel channel section 7 along each side edge, its open face outwards opposite the box's channel, reaching 100 mm past the table's front for the handle. Lay 10 mm steel balls 8 between each pair of opposed channels, three a side, spaced along, and slide the table in so it runs level with the box's top. Fit a hardwood handle 9 across the angles' front ends, and stops 10, 11 and 12 to limit the stroke to 450 mm.

Material untuk langkah ini:

Lembaran kayu lapisLembaran kayu lapis1 buah
Profil baja kanal UProfil baja kanal U2 buah
Bantalan peluruBantalan peluru1 buah
Papan Kayu KerasPapan Kayu Keras1 buah
Aneka baut segi enamAneka baut segi enam8 buah
Mur Segi EnamMur Segi Enam8 buah
Sekrup kayuSekrup kayu12 buah

Alat yang dibutuhkan:

Gergaji Ukir ListrikGergaji Ukir Listrik
Bor Tanpa KabelBor Tanpa Kabel
Set Mata BorSet Mata Bor
Gergaji BesiGergaji Besi
Set KikirSet Kikir
Kunci InggrisKunci Inggris
Siku KombinasiSiku Kombinasi
5

Hang the saw under the table

Bolt the circular saw by its own base plate under the table, the blade up through the slot, the saw's depth set so the blade stands 10 mm above the thickest work. For angle cuts use the saw's own bevel adjustment, which does what his arcuate bracket 17 did. Tape or lock the saw's trigger on, so the new switch alone controls it.

Material untuk langkah ini:

Gergaji bundarGergaji bundar1 buah
Aneka baut segi enamAneka baut segi enam4 buah

Alat yang dibutuhkan:

Bor Tanpa KabelBor Tanpa Kabel
Set Mata BorSet Mata Bor
Kunci InggrisKunci Inggris
Siku KombinasiSiku Kombinasi
6

The self-acting switch

Screw a lever microswitch rated for the saw's current inside one side panel, its lever 24 pointing up into the path of the table, with an outlet for the saw's plug and a supply cord through the panel, as his switch box 22 and socket; have it wired by an electrician. Bend a finger 25 of spring steel and screw it on a bracket 26 under the table, set so that, as the table goes forward, it flips the lever on 60 mm into the stroke, and as the table comes back it flips it off 40 mm before the end. Check it with the saw unplugged: you should hear the click each way.

Material untuk langkah ini:

Mikrosakelar (digerakkan tuas)Mikrosakelar (digerakkan tuas)1 buah
Pita baja pegasPita baja pegas1 buah
Besi Strip Baja LunakBesi Strip Baja Lunak1 buah
Sekrup kayuSekrup kayu6 buah

Alat yang dibutuhkan:

Gunting sengGunting seng
Ragum MejaRagum Meja
Bor Tanpa KabelBor Tanpa Kabel
Set Mata BorSet Mata Bor
Set obengSet obeng
7

Rip fence and mitre gauge

Cut a half-round steel plate 27 to lie over the front of the box beside the saw, turn its straight edge up as a flange 28 and bolt a hardwood fence 29 to it, notched 30 for the blade. Pivot a link 31 on top of the plate and a link 32 under it at the centre of its arc; pivot a third link 33 on 31's end; take 32 and 33 back to a flange on the side of the box. Mark the plate in degrees and drill rows of holes along the arcs, and set the fence with a pin through link 31 into a hole, clamped by two wing-nut clamps 35, 36.

Material untuk langkah ini:

Pelat Baja LunakPelat Baja Lunak1 buah
Papan Kayu KerasPapan Kayu Keras1 buah
Besi Strip Baja LunakBesi Strip Baja Lunak2 buah
Batang bulat baja lunakBatang bulat baja lunak1 buah
Aneka baut segi enamAneka baut segi enam6 buah
Mur sayapMur sayap2 buah

Alat yang dibutuhkan:

Gunting sengGunting seng
Gergaji BesiGergaji Besi
Ragum MejaRagum Meja
Mesin Bor DudukMesin Bor Duduk
Set Mata BorSet Mata Bor
Busur DerajatBusur Derajat
PenggoresPenggores
PenitikPenitik
Set KikirSet Kikir
8

Cut

With the table fully back, hold a board against the fence with one hand and push the handle with the other. The saw starts by itself before the blade reaches the board, cuts through, and stops as you bring the table back.

Alat yang dibutuhkan:

Kacamata pengamanKacamata pengaman
Pelindung telinga (penutup telinga, SNR 30 dB)Pelindung telinga (penutup telinga, SNR 30 dB)
9

Troubleshooting

Sliding table saw troubleshooting.

Flow

Loading...
10

History and honest limits

**Mearl V. Tracy** of Sacramento, California, assignor of one-half to Marion M. Tracy, US 2,260,421, dated 28 October 1941, filed 18 April 1938. His one claim is the switch: a snap switch with a trigger moved one way or the other by "a resilient finger mounted on the table" that then passes and leaves the trigger, near but before each end of the stroke. He removed the hand saw's shoe and fixed its mounting block on an arcuately slotted bracket; modern saws differ, so we mount it by its base plate and use its own bevel adjustment. His box is sheet metal with the channels on bent beams; ours is plywood with steel channel sections. He gives no sizes; every size here is ours.

Bahan

15

Alat yang Diperlukan

18

Cetak biru ini membuat

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...