SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Twisted-Strip Egg Beater: Faces Beat and Edges Cut
James P. McLean and Philemon A. Morley, Brooklyn, New York · Public domain (expired patent)
Martin

Dibuat oleh

Martin

6. Oktober 2026NO
6
0
0
0
0

Twisted-Strip Egg Beater: Faces Beat and Edges Cut

A wire beater passes through the egg and leaves a wake without much froth. James P. McLean and Philemon A. Morley of Brooklyn received US 28,760, dated 19 June 1860, for an egg beater of corrugated or twisted strips of tin turned inside a can by a large and a small cog gear set between the double heads of its lid: "by means of twisted or corrugated strips of metal the gelatin mass is beaten by the flat surfaces as well as being broken or cut by the sharp edges thereof." This rung works out how much of a twisted face pushes, then prints the gears and a cage of twisted strips, builds the lid drive on a can, and times a beating.
Menengah
About 4 hours, plus printing

Instruksi

1

How a twisted face beats

Memuat notebook Jupyter…
2

A geared wire beater before it

The embedded blueprint beats with bent wires. McLean and Morley use twisted strips with faces and edges.
3

Read US 28,760

"The superiority of our arrangement of egg beaters over those that are in common use, is that by means of twisted or corrugated strips of metal the gelatin mass is beaten by the flat surfaces as well as being broken or cut by the sharp edges thereof, hence the action is analogous to the motion produced by the hand and spoon, whereas an ordinary wire beater simply passes through the egg like the rudder of a boat, leaving a simple wake behind it without producing an immediate fomentation as is the case with our beater."
4

Print the gears and cage

Print the 36-tooth gear (/uploads/blueprints/twisted-strip-egg-beater-gear-36.stl), the 12-tooth gear (/uploads/blueprints/twisted-strip-egg-beater-gear-12.stl) and the cage of four twisted strips (/uploads/blueprints/twisted-strip-egg-beater-cage.stl). Print in PETG at 0.2 mm layers, 30 % infill, 4 walls.

Material untuk langkah ini:

Filamen PETGFilamen PETG1 buah

Alat yang dibutuhkan:

Pencetak 3D filamen (FDM)Pencetak 3D filamen (FDM)
5

Make the double lid

Cut two plywood disks to the can's mouth. Space them 20 mm apart on three M5 screws with nuts, and drill both for the crank shaft and the cage shaft 48 mm apart.

Material untuk langkah ini:

Lembaran kayu lapisLembaran kayu lapis1 buah
Sekrup mesinSekrup mesin1 buah
Mur Segi EnamMur Segi Enam1 buah
Ring RataRing Rata1 buah

Alat yang dibutuhkan:

Gergaji CopingGergaji Coping
Bor Tanpa KabelBor Tanpa Kabel
Set Mata BorSet Mata Bor
Kunci InggrisKunci Inggris
Jangka Sorong Digital 6 InciJangka Sorong Digital 6 Inci
6

Fit the shafts and gears

Epoxy the large gear on a crank shaft of 5 mm rod with a bent handle, and the small gear on the cage shaft, both between the heads. Epoxy the cage on the cage shaft's lower end.

Material untuk langkah ini:

Batang Baja LunakBatang Baja Lunak1 buah
Epoksi dua komponenEpoksi dua komponen1 buah

Alat yang dibutuhkan:

Gergaji BesiGergaji Besi
Ragum MejaRagum Meja
Tang Berujung RataTang Berujung Rata
7

The patent drawing

US 28,760 drawing sheet, public domain (expired patent).
Langkah 7 - Image 1
8

Beat egg whites

Put two egg whites in the can, fit the lid, and crank about once a second; time to stiff peaks.
Langkah 8 - Image 1

Material untuk langkah ini:

KalengKaleng1 buah
TelurTelur2 buah

Alat yang dibutuhkan:

StopwatchStopwatch
9

Gears that skip, a cage that scrapes

Twisted-strip egg beater troubleshooting.

Flow

Loading...
10

History and honest limits

**James P. McLean** and **Philemon A. Morley** of Brooklyn, assignors to P. A. Morley, received US 28,760, dated 19 June 1860. Their Fig. 2, for bakers, puts the strips on a vertical water-tight cylinder turning round a stationary handle, driven by a hand wheel whose rubber band grips the cylinder's grater-like funnel top instead of cog wheels. They claimed the twisted beaters in combination with the cylinder. **Honest limits.** FDM prints hold food in their layer lines, so wash well and replace when worn. Printed strips and plywood heads stand in for tin. Your times are the result.

Bahan

9
  • 4
    Filamen PETG
    1 buah
    Placeholder
  • 5
    Lembaran kayu lapis
    1 buah
    Placeholder
  • 5
    Sekrup mesin
    1 buah
    Placeholder
  • 5
    Mur Segi Enam
    1 buah
    Placeholder
  • 5
    Ring Rata
    1 buah
    Placeholder
  • 6
    Batang Baja Lunak
    1 buah
    Placeholder
  • 6
    Epoksi dua komponen
    1 buah
    Placeholder
  • 8
    Kaleng
    1 buah
    Placeholder
  • 8
    Telur
    2 buah
    Placeholder

Alat yang Diperlukan

10

Blueprint terkait

Blueprint ini berbagi pengetahuan — teknik, bahan, atau prinsip

Counter-Rotating Egg Beater: One Wheel, Two Beaters Turning Opposite Ways

Counter-Rotating Egg Beater: One Wheel, Two Beaters Turning Opposite Ways

oleh MartinNO

MAKANAN & MINUMAN

6
0
0
0
0
0
Stepped Spiral Egg Beater: A Stepped Dasher Spun in a Square Box

Stepped Spiral Egg Beater: A Stepped Dasher Spun in a Square Box

oleh MartinNO

MAKANAN & MINUMAN

6
0
0
0
0
0
Gear Trains: Idlers, Compounding and Hitting a Given Ratio

Gear Trains: Idlers, Compounding and Hitting a Given Ratio

oleh MartinNO

Mekanika

25
0
0
0
0
0

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...