कला
सौंदर्य और कल्याण
हस्तशिल्प
संस्कृति और इतिहास
मनोरंजन
पर्यावरण
खाद्य और पेय
रिवर्स इंजीनियरिंग
विज्ञान
खेल
प्रौद्योगिकी
पहनने योग्य
Brass Sheet, Strip and Rod from an Ingot
Forge

द्वारा बनाया गया

Forge

11. अक्टूबर 2026NO
3
0
0
0
0

Brass Sheet, Strip and Rod from an Ingot

Brass from the alloying blueprint is cast into bars, then worked cold like copper: rolled or hammered for sheet and strip, drawn for rod. It work-hardens faster than copper, so it is annealed often, to a dull red, and can be quenched. Molten brass gives off white zinc-oxide smoke: melt it outdoors with the wind behind you.
मध्यवर्ती
A day

निर्देश

1

The brass

Making the brass ingot.
2

Cast bars

Outdoors, melt brass pieces in a crucible in the charcoal forge and pour them into a warmed, dry ingot mould: flat bars for sheet and strip, square bars for rod.

इस चरण के लिए सामग्री:

पीतल की सिल्लीपीतल की सिल्ली1 किलो
लकड़ी का कोयलालकड़ी का कोयला5 किलो

आवश्यक उपकरण:

लोहार की भट्ठीलोहार की भट्ठी
अग्निसह मिट्टी की घरियाअग्निसह मिट्टी की घरिया
क्रूसिबल चिमटाक्रूसिबल चिमटा
पिंड का साँचापिंड का साँचा
चमड़े का एप्रनचमड़े का एप्रन
वेल्डिंग के दस्तानेवेल्डिंग के दस्ताने
सुरक्षा चश्मासुरक्षा चश्मा
3

Anneal

Heat each bar on fire bricks to a dull red with the torch and quench it in water.

इस चरण के लिए सामग्री:

जलजल10 लीटर

आवश्यक उपकरण:

प्रोपेन टॉर्चप्रोपेन टॉर्च
अग्निसह ईंटअग्निसह ईंट
लोहार की संड़सीलोहार की संड़सी
पानी चढ़ाने की बाल्टीपानी चढ़ाने की बाल्टी
4

Roll or hammer sheet and strip

Pass the flat bar through the rolling mill, closing it a little each pass, or hammer it on the anvil. Anneal whenever it stiffens. Cut strip from the sheet with snips.

आवश्यक उपकरण:

बेलन मिलबेलन मिल
निहाईनिहाई
आड़े फन वाला हथौड़ाआड़े फन वाला हथौड़ा
चादर काटने की कैंचीचादर काटने की कैंची
डिजिटल वर्नियर कैलिपर, 6 इंचडिजिटल वर्नियर कैलिपर, 6 इंच
5

Draw rod

Hammer the square bar round, taper the end, and draw it through the drawplate with draw tongs and wax, annealing every few holes.

आवश्यक उपकरण:

निहाईनिहाई
गोल सिरे वाला हथौड़ागोल सिरे वाला हथौड़ा
इस्पात की तारखींच पट्टीइस्पात की तारखींच पट्टी
खींचने का संडासीखींचने का संडासी
बेंच शिकंजाबेंच शिकंजा
6

Clean

Soak in vinegar with salt to lift the oxide, scrub with the wire brush, rinse and dry.

इस चरण के लिए सामग्री:

सिरकासिरका0.5 लीटर
नमकनमक10 ग्रा

आवश्यक उपकरण:

कटोराकटोरा
तार-ब्रुश का सेटतार-ब्रुश का सेट
7

Troubleshooting

Brass working troubleshooting.

Flow

Loading...

सामग्री

5
  • प्लेसहोल्डर
  • प्लेसहोल्डर
  • 10 लीटर
    प्लेसहोल्डर
  • 0.5 लीटर
    प्लेसहोल्डर
  • 10 ग्रा
    प्लेसहोल्डर

आवश्यक उपकरण

22

CC0 पब्लिक डोमेन

यह ब्लूप्रिंट CC0 के तहत जारी किया गया है। आप बिना अनुमति माँगे इस कार्य को किसी भी उद्देश्य के लिए कॉपी, संशोधित, वितरित और उपयोग करने के लिए स्वतंत्र हैं।

उनके ब्लूप्रिंट के माध्यम से उत्पाद खरीदकर मेकर का समर्थन करें जहाँ वे मेकर कमीशन कमाते हैं जो विक्रेताओं द्वारा निर्धारित होता है, या इस ब्लूप्रिंट का नया संस्करण बनाएँ और राजस्व साझा करने के लिए इसे अपने ब्लूप्रिंट में कनेक्शन के रूप में शामिल करें।

चर्चा

(0)

लॉग इन करें चर्चा में शामिल होने के लिए

टिप्पणियाँ लोड हो रही हैं...