कला
सौंदर्य और कल्याण
हस्तशिल्प
संस्कृति और इतिहास
मनोरंजन
पर्यावरण
खाद्य और पेय
रिवर्स इंजीनियरिंग
विज्ञान
खेल
प्रौद्योगिकी
पहनने योग्य

Electronic Analytical Balance: a Coil Current in Place of Weights (Akers et al., 1977)
The equal-arm balance with its weights replaced by electricity. The pan sits on a coil in the gap of a permanent magnet. A load pushes it down; capacitor rings sense the smallest movement, and a servo drives just enough current through the coil to lift it back to its rest position. That current is the weight.
Result: a balance that reads the weight in grams or ounces on a digital display, with no weights to handle, and tare by its circuit.
Source: C. B. Akers and others (Arbor Laboratories), US Patent 4,034,819 (1977). Unknown: the resolution, capacity, magnet type, materials and sizes; the circuits are given as blocks only. Picture: patent drawing.
उन्नत
2 weeks
निर्देश
1
1
Build the magnet circuit
Build the magnet circuit
Stack permanent magnets into a column with a soft iron core. Enclose them in an annular outer housing with end caps, shaped so the field crosses a narrow annular air gap at a constriction. Keep the whole structure symmetrical about its vertical axis. Mount it on a support plate fixed to an upright, such as a housing panel on a base. Not given: the magnet type, materials and sizes.
इस चरण के लिए सामग्री:
चुंबक1 column
लोहे की गोल छड़1 soft iron core
अज्ञात धातु1 housing and end caps
अज्ञात सामग्री1 support plate, panel, baseआवश्यक उपकरण:
पेचकस सेट
अज्ञात माप2
2
Hang the coil in the gap
Hang the coil in the gap
Wind the coil tightly round the middle of a light bobbin that surrounds the core, the coil sitting in the air gap. Tabs at both ends of the bobbin pass out through holes in the end caps to suspension frames. Hang the frames from thin springy cantilevers fixed to the upright, so the bobbin can only move a short way straight up and down. Keep the bobbin and its suspension as light as possible. Put the weighing pan on top. Ours: enamelled wire.
इस चरण के लिए सामग्री:
इनैमल-लेपित ताँबे का तार1 coil
अज्ञात सामग्री1 bobbin, frames, cantilevers
तराज़ू का पलड़ा1 टुकड़ाआवश्यक उपकरण:
अज्ञात माप3
3
Fit the capacitor rings
Fit the capacitor rings
Mount four capacitor rings inside the outer housing, two above and two below the air gap, facing matching rings on the bobbin. Cross-connect them so a tilt of the bobbin cancels out and only up-and-down movement shows. Connect them to a signal generator: as the bobbin moves, one set's capacitance rises and the other's falls, and the difference becomes the control voltage.
इस चरण के लिए सामग्री:
अज्ञात धातु1 rings
इंटीग्रेटेड सर्किट (IC)1 sensing circuit
जोड़ने का तार1 टुकड़ा
सोल्डर तार1 a littleआवश्यक उपकरण:
टाँका लगाने की छड़4
4
Close the servo loop and read the current
Close the servo loop and read the current
Feed the control voltage to a d.c. servo that drives current through the coil, through a flexible lead, until the bobbin is back at its rest position. Pass that current through a large stable resistor, a thermal resistor that corrects for temperature and a calibration potentiometer: the voltage across them stands for the weight. A separate circuit (comparators, saw-tooth generator, oscillator and counter) turns it into a count read out as grams or ounces. Tare is ordinary circuit logic. Ours: a segment LCD; check with calibration weights.
इस चरण के लिए सामग्री:
इंटीग्रेटेड सर्किट (IC)1 servo and counting circuits
प्रतिरोध2 stable resistor, thermal resistor
विभवमापी1 calibration
सेगमेंट एलसीडी पैनल1 display
सोल्डर तार1 a littleआवश्यक उपकरण:
टाँका लगाने की छड़
अंशांकन बाटों का सेटसामग्री
12- 1 columnप्लेसहोल्डर
- 1 soft iron coreप्लेसहोल्डर
- 1 ringsप्लेसहोल्डर
- 1 bobbin, frames, cantileversप्लेसहोल्डर
- 1 coilप्लेसहोल्डर
- 1 टुकड़ाप्लेसहोल्डर
- 1 servo and counting circuitsप्लेसहोल्डर
- 1 टुकड़ाप्लेसहोल्डर
- 2 a littleप्लेसहोल्डर
- 2 stable resistor, thermal resistorप्लेसहोल्डर
- प्लेसहोल्डर
- 1 displayप्लेसहोल्डर
कनेक्टेड ब्लूप्रिंट सामग्री
यह ब्लूप्रिंट बनाता है
संबंधित ब्लूप्रिंट
ये ब्लूप्रिंट ज्ञान साझा करते हैं — तकनीक, सामग्री या सिद्धांत
CC0 पब्लिक डोमेन
यह ब्लूप्रिंट CC0 के तहत जारी किया गया है। आप बिना अनुमति माँगे इस कार्य को किसी भी उद्देश्य के लिए कॉपी, संशोधित, वितरित और उपयोग करने के लिए स्वतंत्र हैं।
उनके ब्लूप्रिंट के माध्यम से उत्पाद खरीदकर मेकर का समर्थन करें जहाँ वे मेकर कमीशन कमाते हैं जो विक्रेताओं द्वारा निर्धारित होता है, या इस ब्लूप्रिंट का नया संस्करण बनाएँ और राजस्व साझा करने के लिए इसे अपने ब्लूप्रिंट में कनेक्शन के रूप में शामिल करें।


