कला
सौंदर्य और कल्याण
हस्तशिल्प
संस्कृति और इतिहास
मनोरंजन
पर्यावरण
खाद्य और पेय
रिवर्स इंजीनियरिंग
विज्ञान
खेल
प्रौद्योगिकी
पहनने योग्य
Equal-Arm Balance on a Knife Edge, with a Set of Brass Weights
Penny

द्वारा बनाया गया

Penny

14. अक्टूबर 2026DK
25
0
0
4
0

Equal-Arm Balance on a Knife Edge, with a Set of Brass Weights

The oldest weighing machine is a beam with equal arms balanced on a pivot, a pan hanging from each end: put the load in one pan and known weights in the other until the beam lies level. Balances go back to the Fourth Dynasty of Egypt. A hardened knife edge makes it sensitive and a long pointer shows the smallest tilt; the weights are cast in brass and adjusted against each other. The picture: our diagram of the balance, its knife edge, pointer, pans and weights.
मध्यवर्ती
Two to three days

निर्देश

1

Beam and knife edge

File a straight beam from flat tool steel with a hole exactly in the middle and one near each end, the two end holes equally far from the centre. Forge and file a short steel knife edge, harden and temper it, and fit it through the centre hole, edge down. File a long pointer onto the beam.

इस चरण के लिए सामग्री:

चपटी टूल स्टील छड़चपटी टूल स्टील छड़1 टुकड़ा

आवश्यक उपकरण:

धातु रेतीधातु रेती
हाथ-बरमाहाथ-बरमा
डिजिटल वर्नियर कैलिपर, 6 इंचडिजिटल वर्नियर कैलिपर, 6 इंच
लोहार की भट्ठीलोहार की भट्ठी
पानी चढ़ाने की बाल्टीपानी चढ़ाने की बाल्टी
सुरक्षा चश्मासुरक्षा चश्मा
2

Stand and bearing

Make an upright stand of hardwood with a hardened steel V-block on top, shallower than the knife edge, so the beam rocks freely. Mark a zero line behind the pointer.

इस चरण के लिए सामग्री:

कठोर काठ की पट्टीकठोर काठ की पट्टी2 टुकड़े
मृदु इस्पात की छड़मृदु इस्पात की छड़0.3 m

आवश्यक उपकरण:

धातु रेतीधातु रेती
लोहार की भट्ठीलोहार की भट्ठी
पानी चढ़ाने की बाल्टीपानी चढ़ाने की बाल्टी
3

Pans

Cut two equal brass discs, dish them slightly, drill three holes in each rim and hang each from an end hole on three equal cords.

इस चरण के लिए सामग्री:

पीतल की चादरपीतल की चादर1 टुकड़ा
मोमयुक्त लिनन का धागामोमयुक्त लिनन का धागा3 m

आवश्यक उपकरण:

चादर काटने की कैंचीचादर काटने की कैंची
हाथ-बरमाहाथ-बरमा
धातु रेतीधातु रेती
4

Trim to level

With both pans empty, file the heavier side until the pointer rests on zero. Swap the pans and check again: if the pointer moves, the arms are unequal and the end holes need moving.

आवश्यक उपकरण:

धातु रेतीधातु रेती
5

Cast the weights

Melt brass and cast a row of plain cylinders a little heavy in green sand.

इस चरण के लिए सामग्री:

पीतल की सिल्लीपीतल की सिल्ली2 किलो
लकड़ी का कोयलालकड़ी का कोयला1 as required
ढलाई की रेतढलाई की रेत5 किलो

आवश्यक उपकरण:

लोहार की भट्ठीलोहार की भट्ठी
अग्निसह मिट्टी की घरियाअग्निसह मिट्टी की घरिया
क्रूसिबल चिमटाक्रूसिबल चिमटा
ढलाई का साँचा-संदूक (ऊपरी और निचला)ढलाई का साँचा-संदूक (ऊपरी और निचला)
वेल्डिंग के दस्तानेवेल्डिंग के दस्ताने
6

Adjust the weights

Balance the largest weight against a litre of water measured in the cylinder (one kilogram, our reference), filing it down until the beam is level. Make the smaller ones by balancing pairs against a larger one and against each other, filing each to level.

इस चरण के लिए सामग्री:

जलजल1 लीटर

आवश्यक उपकरण:

अंशांकित सिलिंडरअंशांकित सिलिंडर
धातु रेतीधातु रेती
7

A binary set of weights

Jupyter नोटबुक लोड हो रही है…
8

Limits

The balance's form and use are as Wikipedia describes; the sizes and the water reference are ours. Water's density changes a little with temperature, so the reference is good to a few parts in a thousand.

सामग्री

9

आवश्यक उपकरण

12

संबंधित ब्लूप्रिंट

ये ब्लूप्रिंट ज्ञान साझा करते हैं — तकनीक, सामग्री या सिद्धांत

CC0 पब्लिक डोमेन

यह ब्लूप्रिंट CC0 के तहत जारी किया गया है। आप बिना अनुमति माँगे इस कार्य को किसी भी उद्देश्य के लिए कॉपी, संशोधित, वितरित और उपयोग करने के लिए स्वतंत्र हैं।

उनके ब्लूप्रिंट के माध्यम से उत्पाद खरीदकर मेकर का समर्थन करें जहाँ वे मेकर कमीशन कमाते हैं जो विक्रेताओं द्वारा निर्धारित होता है, या इस ब्लूप्रिंट का नया संस्करण बनाएँ और राजस्व साझा करने के लिए इसे अपने ब्लूप्रिंट में कनेक्शन के रूप में शामिल करें।

चर्चा

(0)

लॉग इन करें चर्चा में शामिल होने के लिए

टिप्पणियाँ लोड हो रही हैं...