همکاری
هنر
زیبایی و سلامت
صنایع دستی
فرهنگ و تاریخ
سرگرمی
محیط زیست
غذا و نوشیدنی
مهندسی معکوس
علوم
ورزش
فناوری
پوشیدنی‌ها
Adjustable Bench Power Supply: Constant Voltage / Constant Current with Cross-Over Lamps (Gately, Forbro, US 3,303,411, 1967)
Ed

ایجاد شده توسط

Ed

3. نوامبر 2026FI
۴
۰
۰
۰
۰

Adjustable Bench Power Supply: Constant Voltage / Constant Current with Cross-Over Lamps (Gately, Forbro, US 3,303,411, 1967)

An all-transistor bench supply with two knobs: one sets the voltage, the other the current. It holds the set voltage until the load tries to draw more than the set current, then switches at once to holding the current, and back again, with no in-between state. Two lamps show which mode is in control. Result: an adjustable constant-voltage / constant-current DC supply with mode lamps. Source: J. R. Gately (Forbro Design), US 3,303,411 (1967). Unknown: all component values and ratings. Builds on the same inventor's 1966 current-limited supply. Picture: the patent drawing.
پیشرفته
Unknown

دستورالعمل‌ها

1

Build the raw supplies

In a case, wire the cord through a switch and fuse to two power transformers, each with rectifiers and a filter: one gives the main power to be regulated, the other the bias supplies, held steady by Zener diodes. Not given: the voltages. Ours: the case, switch and fuse.

مواد مورد نیاز این مرحله:

جعبهٔ آلومینیومیجعبهٔ آلومینیومی1 قطعه
سیم انعطاف‌پذیر با دوشاخهسیم انعطاف‌پذیر با دوشاخه1 قطعه
کلید اهرمیکلید اهرمی1 قطعه
فیوزفیوز1 قطعه
ترانسفورماتور کاهندهترانسفورماتور کاهنده2 قطعه
دیوددیود6 rectifiers
خازن الکترولیتیخازن الکترولیتی3 filters
دیود زنردیود زنر2 bias

ابزارهای مورد نیاز:

دریل دستیدریل دستی
مجموعه پیچ‌گوشتیمجموعه پیچ‌گوشتی
2

Fit the pass transistor and current bridge

Put a power transistor on a heat sink in series with the output: collector to the negative supply, emitter through a current-sensing resistor to the negative output terminal. Make the current bridge from the sensing resistor, a reference Zener, a reference resistor and the adjustable current-control resistor: the output current is proportional to its setting. A small trimming resistor sets the maximum current. Not given: the values.

مواد مورد نیاز این مرحله:

ترانزیستور قدرتترانزیستور قدرت1 series pass
گرماگیرگرماگیر1 قطعه
دیود زنردیود زنر1 current reference
رئوستارئوستا1 current control
مقاومتمقاومت1 sensing, reference, trim set
پست اتصالپست اتصال2 output + and -

ابزارهای مورد نیاز:

هویههویه
3

Build the voltage bridge

Make the voltage bridge from a reference Zener, a reference resistor, the adjustable voltage-control resistor and the load itself across the output. A small trimming resistor sets the maximum voltage. Add two resistors that feed the current bridge enough extra to cover the voltage bridge's own current and any voltmeter across the output, so low currents are still held exactly.

مواد مورد نیاز این مرحله:

دیود زنردیود زنر1 voltage reference
رئوستارئوستا1 voltage control
مقاومتمقاومت1 reference, trim, compensation set

ابزارهای مورد نیاز:

هویههویه
4

Build the amplifiers and cross-over

Give each bridge an error amplifier. Feed the two amplified errors to the bases of a pair of transistors sharing one emitter resistor: whichever base is the more negative takes control and cuts the other off, so the supply is always cleanly in voltage mode or current mode. Amplify the shared emitter signal through two more transistors to drive the pass transistor's base. Add an emitter-follower clamp on the bias line. Not given: the transistor types.

مواد مورد نیاز این مرحله:

برد مدار چاپیبرد مدار چاپی1 قطعه
مجموعهٔ ترانزیستورمجموعهٔ ترانزیستور1 error amplifiers, cross-over pair, drivers, clamp
مقاومتمقاومت1 مجموعه
پتانسیومترپتانسیومتر1 clamp divider
سیم لحیمسیم لحیم1 as needed

ابزارهای مورد نیاز:

هویههویه
5

Fit the mode lamps and use it

From the cross-over pair, drive two lamp transistors, each lighting one lamp: one for voltage mode, one for current mode. In use, set the voltage and the current limit. With a light load the voltage lamp is lit and the voltage holds; if the load tries to draw more than the set current, the supply switches to holding the current and the current lamp lights.

مواد مورد نیاز این مرحله:

مجموعهٔ ترانزیستورمجموعهٔ ترانزیستور1 two lamp drivers
سرپیچ لامپسرپیچ لامپ2 قطعه
لامپلامپ2 قطعه

ابزارهای مورد نیاز:

مجموعه پیچ‌گوشتیمجموعه پیچ‌گوشتی

مواد

19
  • جایگزین
  • جایگزین
  • 1 قطعه
    1 vendor sell this, none ship to you yet
    جایگزین
  • 1 قطعه
    جایگزین
  • جایگزین
  • 6 rectifiers
    جایگزین
  • جایگزین
  • 1 voltage reference
    جایگزین
  • جایگزین
  • 1 قطعه
    جایگزین
  • 1 voltage control
    جایگزین
  • 1 مجموعه
    جایگزین
  • 2 output + and -
    2 vendors sell this, none ship to you yet
    جایگزین
  • جایگزین
  • جایگزین
  • 1 clamp divider
    15 vendors sell this, none ship to you yet
    جایگزین
  • 1 as needed
    جایگزین
  • جایگزین
  • 2 قطعه
    جایگزین

ابزارهای لازم

3
  • جایگزین
  • جایگزین
  • 2 vendors sell this, none ship to you yet
    جایگزین

نقشه‌های مرتبط

این نقشه‌ها دانش مشترکی دارند — تکنیک‌ها، مواد یا اصول

CC0 مالکیت عمومی

این نقشه تحت مجوز CC0 منتشر شده است. شما آزاد هستید آن را کپی، ویرایش، توزیع و برای هر هدفی بدون نیاز به اجازه استفاده کنید.

با خرید محصولات از طریق نقشه از سازنده حمایت کنید و او کمیسیون سازنده تعیین شده توسط فروشندگان، دریافت می‌کند یا یک نسخه جدید از این نقشه ایجاد کنید و آن را به عنوان اتصال در نقشه خود قرار دهید تا درآمد به اشتراک گذاشته شود.

بحث و گفتگو

(0)

ورود برای شرکت در بحث

در حال بارگذاری نظرات...