همکاری
هنر
زیبایی و سلامت
صنایع دستی
فرهنگ و تاریخ
سرگرمی
محیط زیست
غذا و نوشیدنی
مهندسی معکوس
علوم
ورزش
فناوری
پوشیدنی‌ها
Blake Jaw Breaker: Eccentric, Pitman and Two Toggles Swing a Steel Jaw Against a Fixed Chilled Plate (Richards, Ore Dressing, 1903)
Forge

ایجاد شده توسط

Forge

15. نوامبر 2026NO
۷
۰
۰
۰
۰

Blake Jaw Breaker: Eccentric, Pitman and Two Toggles Swing a Steel Jaw Against a Fixed Chilled Plate (Richards, Ore Dressing, 1903)

Eli Whitney Blake's jaw breaker (patented 1858), the standard first crusher of the ore mill, as Robert Richards described it: a ribbed cast frame on four legs, a fixed jaw bedded in zinc, a steel swing jaw hung from a shaft at the top, and an eccentric that lifts a pitman to straighten two toggles and push the jaw shut; rubber springs pull it back. A wedge sets the gap; a heavy flywheel carries it through each half-turn of crushing.
پیشرفته
Weeks (castings and machining)

دستورالعمل‌ها

1

Sizes and power

در حال بارگذاری دفترچهٔ Jupyter…
2

Read Richards

"As the eccentric lifts the pitman, it straightens out the toggles, lengthening the distance between their outer ends. This forces the swing jaw to approach the fixed jaw, crushing the rock."
3

Frame and fixed jaw

Cast the frame of strong, ribbed cast iron or cast steel, with four legs bolted down, bearing boxes on top for the swing-jaw shaft and the eccentric shaft, and a horizontal web at the rear for the toggle block and wedge. Bed the fixed jaw against the frame end with 1/4 in. (6 mm) of zinc, and hold its jaw plate with two wedge-shaped cheek plates driven into recesses in the frame.

مواد مورد نیاز این مرحله:

قطعات ریختگی چدنیقطعات ریختگی چدنی1 قطعه
شمش رویشمش روی1 قطعه
مجموعهٔ پیچ‌های شش‌گوشمجموعهٔ پیچ‌های شش‌گوش1 قطعه

ابزارهای مورد نیاز:

ملاقهٔ ریخته‌گریملاقهٔ ریخته‌گری
قرقرهٔ مرکبقرقرهٔ مرکب
چکشچکش
4

Swing jaw

Make the swing jaw of steel, fixed to its shaft by a gib and key bolt, with its jaw plate held by dovetails, a steel toggle bearing at the back and an eye near the bottom for the spring rod. Jaw plates: chilled cast iron with lengthwise 90° corrugations.

مواد مورد نیاز این مرحله:

قطعات ریختگی چدنیقطعات ریختگی چدنی1 قطعه
محور فولادیمحور فولادی1 قطعه

ابزارهای مورد نیاز:

تراش فلزتراش فلز
مجموعهٔ آچار تختمجموعهٔ آچار تخت
5

Pitman, toggles and wedge

Hang a strong steel pitman from the eccentric shaft on babbitt bearings taken up by a key. Fit two toggles: one between the toggle block and the pitman, one between the pitman and the swing jaw, all four toggle bearings steel, held by set screws. Set the toggle block on its bolt against the wedge, which an adjusting bolt raises or lowers.

مواد مورد نیاز این مرحله:

محور فولادیمحور فولادی1 قطعه
فلز نامعلومفلز نامعلوم1 قطعه
قطعات ریختگی چدنیقطعات ریختگی چدنی1 قطعه

ابزارهای مورد نیاز:

تراش فلزتراش فلز
مجموعهٔ آچار تختمجموعهٔ آچار تخت
6

Springs, flywheel and drive

Fit two spring rods from the swing jaw through rubber springs held in compression against a spring bar. Key a heavy flywheel to the eccentric shaft and bolt the drive pulley to it; plug all oil holes against grit and shield the boxes and toggles with the half hopper. Drive it by belt (Table 5: 275 rev./min).

مواد مورد نیاز این مرحله:

ورق لاستیک طبیعیورق لاستیک طبیعی1 قطعه
قطعات ریختگی چدنیقطعات ریختگی چدنی1 قطعه
قرقرهقرقره1 قطعه
تسمهٔ انتقال نیروتسمهٔ انتقال نیرو1 قطعه
مجموعهٔ پیچ‌های شش‌گوشمجموعهٔ پیچ‌های شش‌گوش1 قطعه

ابزارهای مورد نیاز:

مجموعهٔ آچار تختمجموعهٔ آچار تخت
تراش فلزتراش فلز
7

Run and adjust

Feed rock by hand, shovel or chute into the mouth. As the jaw plates wear and the product gets coarse, raise the wedge by its nut; when that is used up, fit longer toggles that keep the pitman vertical; then turn the jaw plates end for end; last, fit new plates.

ابزارهای مورد نیاز:

مجموعهٔ آچار تختمجموعهٔ آچار تخت
8

Troubleshooting

Jaw breaker troubleshooting.

Flow

Loading...
9

History and honest limits

From Robert H. Richards, *Ore Dressing* vol. I (1903), Chapter II, §§ 11-14, pp. 13-17, Figs. 5-8 and Table 5 (checked on the archive.org scan oredressing01richuoft; p. 15 from its text layer). Blake's first 1858 form gave the most movement at the mouth; he soon reversed it so the bottom of the jaw moves most. Richards describes a bought Farrel or Fraser & Chalmers machine: building it from castings and metric figures are ours, and the babbitt alloy has no head yet.

مواد

8

ابزارهای لازم

5

این نقشه می‌سازد

CC0 مالکیت عمومی

این نقشه تحت مجوز CC0 منتشر شده است. شما آزاد هستید آن را کپی، ویرایش، توزیع و برای هر هدفی بدون نیاز به اجازه استفاده کنید.

با خرید محصولات از طریق نقشه از سازنده حمایت کنید و او کمیسیون سازنده تعیین شده توسط فروشندگان، دریافت می‌کند یا یک نسخه جدید از این نقشه ایجاد کنید و آن را به عنوان اتصال در نقشه خود قرار دهید تا درآمد به اشتراک گذاشته شود.

بحث و گفتگو

(0)

ورود برای شرکت در بحث

در حال بارگذاری نظرات...