همکاری
هنر
زیبایی و سلامت
صنایع دستی
فرهنگ و تاریخ
سرگرمی
محیط زیست
غذا و نوشیدنی
مهندسی معکوس
علوم
ورزش
فناوری
پوشیدنی‌ها
Iron Ball Mill: Grüson Drum with a Stepped Die Ring and Two Screens (Richards, 1903)
Forge

ایجاد شده توسط

Forge

3. نوامبر 2026NO
۷
۰
۰
۰
۰

Iron Ball Mill: Grüson Drum with a Stepped Die Ring and Two Screens (Richards, 1903)

The Grüson ball mill: a drum turning on a horizontal axis, charged with chilled iron or steel balls of mixed sizes. The balls grind the ore against each other and against a stepped die ring. The ground ore passes out through a coarse and a fine screen; the oversize is carried back in. Result: a mill for fine grinding of cement, fertiliser, clay and soft ores, wet or dry. Sizes from 0.66 m to 1.83 m across. Source: R. H. Richards, Ore Dressing, vol. I (1903), § 225, Figs. 172a-b and Table 149. Unknown: dimensions beyond the table, and the materials of the side plates, screens and shaft. Picture: Richards, Figs. 172a-b.
پیشرفته
Unknown

دستورالعمل‌ها

1

Make the drum and the die ring

The drum is two side plates (b) joined round the edge by the die ring (a). The die ring is five perforated, spiral plates of chilled iron. Each plate laps the next, so they form steps: the balls drop from one step to the next, and the space under each step lets the oversize from the screens back in. Not given: the side-plate material, sizes, hole sizes.

مواد مورد نیاز این مرحله:

قطعات ریختگی چدنیقطعات ریختگی چدنی5 die plates, chilled iron
ماده ناشناختهماده ناشناخته2 side plates

ابزارهای مورد نیاز:

ابعاد نامعلومابعاد نامعلوم
آچار فرانسهآچار فرانسه
2

Put the two screens round it

Outside the die ring, fit a coarse perforated screen (c) to take the wear. It is in five parts with spaces between them and has back-deflecting holes (g). Outside that, fit a fine gauze screen (d). At the end of each section of fine screen, fix a deflector or shovel (f). As the drum turns, it carries the oversize up and back into the grinding space. Not given: the screens' metal and mesh.

مواد مورد نیاز این مرحله:

صفحه سرند سوراخ‌دارصفحه سرند سوراخ‌دار1 coarse screen, 5 parts
توری بافتهٔ سرندتوری بافتهٔ سرند1 fine screen
ماده ناشناختهماده ناشناخته5 deflectors

ابزارهای مورد نیاز:

ابعاد نامعلومابعاد نامعلوم
آچار فرانسهآچار فرانسه
3

Mount and house it

Carry the drum on a horizontal shaft in two bearings; the figures show them on masonry piers. Enclose the drum in a plate iron housing with a discharge spout (e) below, a feed hopper (h) at one end, a manhole (i) and a dust pipe (k) on top. Ours: steel sheet for the plate iron.

مواد مورد نیاز این مرحله:

محور فولادیمحور فولادی1 mill shaft
یاتاقان‌گیریاتاقان‌گیر2 قطعه
ورق فولاد نرمورق فولاد نرم1 housing, spout, hopper

ابزارهای مورد نیاز:

آچار فرانسهآچار فرانسه
ابعاد نامعلومابعاد نامعلوم
4

Fit the drive

Drive the mill by gear and pinion. In the figure, the gear is on the mill shaft and the pinion on a countershaft that carries tight and loose pulleys. A belt from the line shaft runs on the pulleys: on the tight pulley the mill turns, on the loose pulley it stops.

مواد مورد نیاز این مرحله:

چرخ‌دنده بزرگچرخ‌دنده بزرگ1 on the mill shaft
چرخ‌دنده کوچکچرخ‌دنده کوچک1 قطعه
محور فولادیمحور فولادی1 countershaft
یاتاقان‌گیریاتاقان‌گیر2 قطعه
پولی ثابت و پولی هرزپولی ثابت و پولی هرز1 قطعه

ابزارهای مورد نیاز:

تسمهٔ انتقال نیروتسمهٔ انتقال نیرو
آچار فرانسهآچار فرانسه
5

Charge the balls (size sets the charge)

Load chilled iron or steel balls in mixed sizes; mixed sizes grind better than one size. Size is the variable: No. 0 (0.660 m drum, 45 rev/min) takes 15 kg of 40 mm and 45 kg of 80 mm balls, 60 kg in all. No. 2 (1.330 m, 30 rev/min) takes 100 kg each of 100, 115 and 125 mm, 300 kg. No. 4 (1.830 m, 25 rev/min) takes 217 kg each of the same three sizes, 650 kg. The bigger the drum, the slower it turns and the heavier its charge.

مواد مورد نیاز این مرحله:

اجسام خردکننده (گلولهٔ فولادی)اجسام خردکننده (گلولهٔ فولادی)300 kg for No. 2; 60 kg No. 0, 650 kg No. 4

ابزارهای مورد نیاز:

باسکول سکویی صنعتیباسکول سکویی صنعتی
6

Grind

Feed the ore, egg-size, through the hopper and run the mill wet or dry. Power, and output per 24 hours: No. 0 takes 1/4 horse power and grinds 1,680 kg of copper ore to 15 mesh, or 840 kg of chrome iron ore to 130 mesh. No. 2 takes 2 1/2 to 3 horse power: 14,400 kg of brick bats to 20 mesh, or 1,920 kg of emery to 200 mesh. No. 4 takes 9 to 11 horse power: 12,720 kg of gold ores to 40 mesh, or 10,800 kg of chrome iron ore to 130 mesh. Wear: 1,345 kg of balls for 102,400 barrels of cement, about 0.139 lb a ton. The end plates last 18 months. Hard quartz ores wear the balls too much.

ابزارهای مورد نیاز:

تسمهٔ انتقال نیروتسمهٔ انتقال نیرو
آبآب

مواد

11

ابزارهای لازم

5

CC0 مالکیت عمومی

این نقشه تحت مجوز CC0 منتشر شده است. شما آزاد هستید آن را کپی، ویرایش، توزیع و برای هر هدفی بدون نیاز به اجازه استفاده کنید.

با خرید محصولات از طریق نقشه از سازنده حمایت کنید و او کمیسیون سازنده تعیین شده توسط فروشندگان، دریافت می‌کند یا یک نسخه جدید از این نقشه ایجاد کنید و آن را به عنوان اتصال در نقشه خود قرار دهید تا درآمد به اشتراک گذاشته شود.

بحث و گفتگو

(0)

ورود برای شرکت در بحث

در حال بارگذاری نظرات...